Related Manuals for Stealth Products ADI Basic Release Hardware
Summary of Contents for Stealth Products ADI Basic Release Hardware
- Page 1 Back Support ADI Basic Release Hardware Owner’s Manual - Maintenance Guide ADI Basic Release Hardware for Aluminum Backs...
-
Page 2: Customer Satisfaction
For further assistance, or more advanced applications, please contact your supplier or Stealth Products at (512) 715-9995 or toll free at (800) 965-9229. Always keep the operating instructions in a safe place so they may be referenced as necessary. -
Page 3: Important Information
Warranty Our products are designed, manufactured, and produced to the highest of standards. If any defect in material or workmanship is found, Stealth Products will repair or replace the product at our discretion. Any implied warranty, including the implied warranties of merchantability and fitness for a particular purpose, shall not extend beyond the duration of this warranty. -
Page 4: Warning Labels
Stealth Products does not hold responsibility for final integration of final assembly of product to end user. Stealth Products is not liable for user death or injury. -
Page 5: Table Of Contents
Customer Satisfaction ..............1 Important Information..............2-3 Warranty ...................... 2 Supplier Reference................... 2 Warning Labels..................3 Limited Liability..................3 Table of Contents ................4 Parts and Accessories ..............5 Tools Required for Installation and Adjustment ......5 Parts Required ................... 5 Torque Specifications................ -
Page 6: Parts And Accessories
Parts and Accessories Tools Required for Installation and Adjustment • 4mm allen wrench • 10mm wrench • Torque wrench Parts Required • Top Latch, 2 each (A) • Bottom Catch, 2 each (B) • Back Support Shell, Cushion and Cover, 1 each (C) •... -
Page 7: Installation Instructions
Installation Instructions Step 1 Fasten top slide latches and bottom catches to wheelchair back posts: 1. Remove existing wheelchair back according to the original manufacturer's instructions. 2. Visually determine the desired height of your new ADI back support. Mark on each back post the needed location to attach the left and right bottom catch. -
Page 8: Step 2 - Installation
Installation Instructions Step 2 Removing and attaching back support to back posts: To Remove Hardware: 1. Press left and right top latch release button to unlocked position. 2. Tilt back support forward at a slight angle and lift out of the way from the wheelchair. -
Page 9: Step 3 - Adjustment
Installation Instructions Step 3 Adjustment of height, angle, and depth to user's preference. Height Adjustment 1. With a 4mm allen wrench, loosen the top slide latch and the bottom catch. 2. Position the back along the back canes at the desired height. 3. - Page 10 Installation Instructions Angle Adjustment 1. On each side of the hardware, loosen the top and bottom bolts using a 4mm allen wrench and a 10mm wrench. 2. Adjust the back support to achieve desired user angle.. 3. After final adjustments are complete, tighten all screws to the proper torque specification.
-
Page 11: First-Time Use
First Time Use Dealer Assistance During first time use by the client, it is advised that the dealer or service technician assists and explains the set-up to the customer (the user and/or the attendant). If needed, the dealer may make final adjustments. ADI backs may not fit every chair. -
Page 12: Maintenance
Maintenance Cleaning • Use a soft cloth to clean the back shell. • Hand wash the foam pad cover with mild, soapy water or detergent and let dry. • Foam pad should NOT get wet. DO NOT immerse foam in water. WARNING DO NOT wash or machine dry. -
Page 13: Notes
Notes... - Page 14 Notes...
- Page 15 Notes...
- Page 16 © 2020, Stealth Products, LLC Stealth Products, LLC · info@stealthproducts.com · www.stealthproducts.com (800) 965-9229 | (512) 715-9995 | 104 John Kelly Drive, Burnet, TX 78611 P116D215R6__US__BasicReleaseADI.afpub Oct 30, 2023...
Need help?
Do you have a question about the ADI Basic Release Hardware and is the answer not in the manual?
Questions and answers