Subscribe to Our Youtube Channel
Related Manuals for Total TJSLI8501 Series
Summary of Contents for Total TJSLI8501 Series
- Page 1 PRODUCT MANUAL LITHIUM-ION JIG SAW TJSLI8501x, TJSLI85011y, TJSLI85012y (x=blank, E, 5, 6, 7, 9) (y=blank, E, S, 1, 2, 3, 4, 5, 6, 7, 8, 9)
-
Page 2: General Safety Warnings
Original Instructions GENERAL SAFETY WARNINGS Warning! risk of electric shock if your body is earthed or grounded. Read all safety warnings and all c) Do not expose power tools to rain instructions. or wet conditions. Water entering a power tool will increase the risk of Failure to follow the warnings and electric shock. - Page 3 c) Prevent unintentional starting. any adjustments, changing accesso- Ensure the switch is in the off-po- ries, or storing power tools. Such pre- sition before connecting to power ventive safety measures reduce the risk source and/or battery pack, pick- of starting the power tool accidentally. ing up or carrying the tool.
- Page 4 BATTERY TOOL SAFETY WARNINGS Save these instructions may cause irritation or burns. e)Do not use a battery pack or tool that Warning! is damaged or modified. Damaged or modified batteries may exhibit un- Only use genuine original batter- predictable behavior resulting in fire, ies.Use of non-genuine batter- explosion or risk of injury.
- Page 5 Important safety instructions for (2)Avoid storing battery cartridge in a battery cartridge container with other metal objects such as nails, coins, etc. 1. Before using battery cartridge, read all instructions and cautionary mark- (3)Do not expose battery cartridge to ings on (1) battery charger, (2) bat- water or rain.
- Page 6 THE SYMBOLS IN INSTRUCTION MANUAL Volts Hertz n。 No load speed Rated speed /min Per minute Beats per minute Impacts per minute Oscillations per minute Revolutions per minute Amp hours Safety alert. Please only use the accessories supported by the manufacturer. CE conformity.
- Page 7 THE SYMBOLS IN INSTRUCTION MANUAL Do not destroy battery by fire. Do not expose battery to water. Waste electrical products should not be disposed of with house- hold waste.Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
-
Page 8: Additional Safety Warnings
ADDITIONAL SAFETY WARNINGS Cordless jig saw safety Warning! Warning! 1. Hold power tool by insulated 10. Do not leave the tool run- gripping surfaces, when per- ning. Operate the tool only when forming an operation where the hand-held. cutting accessory may contact 11. -
Page 9: Specified Conditions Of Use
SPECIFIED CONDITIONS properly maintained. OF USE b) Injuries and damage to property to due to broken accessories that are suddenly dashed. The power tool is intended for making separating cuts and cut-outs in wood, plastic, metal, ceramic plates and Warning! rubber while resting firmly on the work- piece. -
Page 10: Specifications
SPECIFICATIONS Components list 1. Switch push button 5. Parallel guide 2. Trigger switch 6. Battery pack 3. Pendulum action switch 7. Base plate 4. Blade holder Accessories 5 pcs Jig saw 1 pcs Parallel guide 1 pcs Hex key... -
Page 11: Technical Specifications
SPECIFICATIONS Technical specifications TJSLI8501x, TJSLI85011y, TJSLI85012y Model (x=blank, E, 5, 6, 7, 9), (y=blank, E, S, 1, 2, 3, 4, 5, 6, 7, 8, 9) Length of stroke 20mm wood 80mm Max. cutting capacities Mild steel Strokes per minute 0-2400/min Rated voltage D.C. - Page 12 OPERATION PICTURE Button Red indicator Battery Cutting action cartridge changing lever Lock-off button Switch trigger Lock-off button Bolt Blade holder Roller Bolt Blade Hex wrench Cutting line Base...
- Page 13 OPERATION PICTURE Hex wrench Base Bolt Starting hole Hex wrench Bolt Rip fence Fence guide...
-
Page 14: Operation
OPERATION Caution cutting stroke and greatly increases cutting speed. Always be sure that the tool is To change the cutting action, just turn switched off and the battery car- the cutting action changing lever to the tridge is removed before adjust- desired cutting action position. -
Page 15: Electric Brake
Caution Caution • Before inserting the battery • Use only B type blades. Using cartridge into the tool, always blades other than B type blades check to see that the switch causes insufficient tightening of trigger actuates properly and the blade, resulting in a serious returns to the "OFF"... - Page 16 Installing or removing saw Warning! blade If the tool is operated continu- Warning! ously until the battery cartridge has discharged, allow the tool to • Always clean out all chips or rest for 15 minutes before pro- foreign matter adhering to the ceeding with a fresh battery.
-
Page 17: Metal Cutting
Cutouts Metal cutting Cutouts can be made with either of two Always use a suitable coolant (cutting methods A or B. oil) when cutting metal. Failure to do so will cause significant blade wear. Boring a starting hole (see Dia I) The underside of the workpiece can be For internal cutouts without a lead-in greased instead of using a coolant. - Page 18 MAINTENANCE&MALFUNCTIONS Possible malfunctions and methods of their eliminations Malfunction Probable causes Actions ● Switch failure Disconnect the When the machine is ●The power cord or wiring is broken, machine from turned on, the electric power cord plug malfunction; the mains and motor does not work.
- Page 19 TOTAL TOOLS WORLD MADE IN CHINA T0323.V02 TOTAL TOOLS CO., PTE. LTD. No. 45 Songbei Road, Suzhou Industrial Park, China.
Need help?
Do you have a question about the TJSLI8501 Series and is the answer not in the manual?
Questions and answers