Table of Contents
Advertisement
Quick Links
8-ports Unmanaged Industrial Ethernet Switch
Introduction:
IT-ES308-IU-1F are a smart plug-and-play industrial Ethernet
switch, which can provide economical solution for your Ethernet.
Its dustproof fully sealed structure(protective case of IP30 level),
over-current, over-voltage and EMC protected redundant double
power input as well as built-in intelligent alarm design can help
system main tenancy personnel monitor the network operation,
which can work reliably in harsh and dangerous environment.
IT-ES308-IU-1F supports 7 TP ports and 1 fiber ports
(IT-ES308-IU-1F: 7-port 10/100Base-Tx, 1-port 100Base-FX).
TP(RJ45) support 10/100Base-T(X), Full/Half duplex mode, and
auto
MDI/MDI-X
single-/multi-mode, SC/ST/FC connector for optional.
Packing List:
The IT-ES308-IU-1F switch is shipped with following items.
1. Ethernet switch IT-ES308-IU-1F (plus terminal block) ×1
2. Hardware Installation Guide ×1
3. Product Warranty Statement ×1
4. DIN-Rail setting fittings ×1
IT-ES308-IU-1F
Hardware Installation Guide
connection;
100Base-FX
1
supports
Advertisement
Table of Contents
Related Manuals for Intellisystem IT-ES308-IU-1F Series
Summary of Contents for Intellisystem IT-ES308-IU-1F Series
- Page 1 IT-ES308-IU-1F 8-ports Unmanaged Industrial Ethernet Switch Hardware Installation Guide Introduction: IT-ES308-IU-1F are a smart plug-and-play industrial Ethernet switch, which can provide economical solution for your Ethernet. Its dustproof fully sealed structure(protective case of IP30 level), over-current, over-voltage and EMC protected redundant double power input as well as built-in intelligent alarm design can help system main tenancy personnel monitor the network operation, which can work reliably in harsh and dangerous environment.
-
Page 2: Panel Layout
Features: 1. Advanced Ethernet switch technical 2. IEEE802.3/802.3u/802.3x/802.3d,store and forward 3. 10/100M, F/H duplex, MDI/MDI-X auto negotiation 4. Broadcast storm protection 5. Relay output warning for power failure and port break alarm 6. Redundant 24VDC power input (12V～48VDC) 7. Designed for industrial applications. IP30 protection, rugged high-strength metal case Panel Layout: IT-ES308-IU-1F (7 TP ports and 1 fiber port):... - Page 3 Back panel 1. Grounding screw 2. Terminal block (4 bits) for PWR1/PWR2 input, terminal block (2 bits) for relay output 3. Power, port alarm enable switch (ON is enable) 4. Heat dissipation orifices 5. DIN-Rail locating kit 6. Screw hole for wall mounting kit 7.
-
Page 4: Communication Connector
Communication connector: IT-ES308-IU-1F series have 7 10/100BaseT(X) Ethernet ports (RJ45) and 1 100BaseFX (SC/ST type connector) fiber ports. 10/100BaseT(X) Ethernet port The pinout of RJ45 port display as below, connect by UTP or STP. The connect distance is no more than 100m. 100Mbps is used 100Ωof UTP 5, 10Mbps is used 100Ωof UTP 3, 4, 5. - Page 5 MDI (straight-through cable) RJ45 MDI-X (Cross over cable) RJ45 (RX+) (TX+) (RX-) (TX-) (TX+) (RX+) (TX-) (RX-) 100BaseFX port 100Base-FX full-duplex SM or MM port, SC/ST/FC type .The fiber port must be used in pair, TX (transmit) port connect remote switch’s RX (receive) port;...
-
Page 6: Led Indicator
LED Indicator: LED indictor light on the front panel of IT-ES308-IU-1F .the function of each LED is described in the table as below. System indication LED State Description Power1 is being supplied to PWR1 Power1 is not being supplied Power2 is being supplied to PWR2 Power2 is not being supplied When the alarm is enabled,... -
Page 7: Power Input
attached to the Fault contacts form an open circuit when: (1) IT-ES308-IU-1F have lost power from one of the DC power inputs, One of the ports for which the corresponding Port alarm DIP Switch is set to ON is not properly connected. If neither of these two conditions occur, the alarm circuit will be closed. -
Page 8: Installation
Installation： Before installation, confirm that the work environment meet the installation require, including the power needs and abundant space. Whether it is close to the connection equipment and other equipment are prepared or not. Installation require as below 1. Avoid in the sunshine, keep away from the heat fountainhead or the area where in intense EMI. -
Page 9: Wiring Requirements
Wiring Requirements： Be sure to disconnect the power cord before installing and/or wiring your Ethernet Switch. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. If the current goes above the maximum ratings, the wiring could overheat may causing serious damage to your equipment. -
Page 10: Specifications
Specifications: Interface RJ45 Ports: 10/100BaseT(X) auto connection, F /H duplex or force work mode, and support MDI/MDI-X connection Fiber Ports: 100BaseFX ports (SC/ST/FC connector, optional) Single-mode: 20, 40, 60, 80, 100,120Km, optional Multi-mode: 2Km Wavelength: 1310 nm, 1550nm Alarm output interface： One relay alarm output. Support power, port link and network alarm Indicator: Power, Port link, abnormity alarm indication Technology... - Page 11 Approvals EMI：FCC Part 15, CISPR (EN55022) class A EMS: EN61000-4-2(ESD), EN61000-4-3(RS), EN61000-4-4(EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11 Shock: IEC 60068-2-27 Free Fall: IEC 60068-2-32 Vibration: IEC 60068-2-6 Warranty: 5 years Certifications:...
Need help?
Do you have a question about the IT-ES308-IU-1F Series and is the answer not in the manual?
Questions and answers