Product Dimensions; Cutout Dimensions; Clearance Dimensions - KitchenAid KECD806RBL - Pure 30 Inch Smoothtop Electric Cooktop Installation Instructions Manual

Product Dimensions

21-5/16"
(54.1 cm)
depth

Clearance Dimensions

30" (76.2 cm) min - 30" (76.2 cm) model
36" (91.4 cm) min - 36" (91.4 cm) model
when higher than 18" (45.7 cm)
See Note ** for
minimum clearances
Minimum distance
to nearest combustible
vertical surface
extending 18" (45.7 cm)
above cooktop
1" (25.4 mm)
Side clearance — 6" (15.2 cm) minimum clearance between side
of cooktop and side wall is recommended for maximum
ventilation performance.
Rear clearance — 3/4" (19.1 mm) clearance between rear edge of
cooktop and rear wall is recommended.
Motor/blower clearance — 2" (51 mm) minimum clearance
between motor and cabinet is required for proper cooling.
6" (15.2 cm) clearance is recommended for servicing access.
Note: 24" (61 cm) minimum when bottom of wood or metal cabinet is
**
protected by not less than 1/4" (6.4 mm) flame retardant millboard covered
with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking platform
and bottom of unprotected wood or sheet metal.
30-3/8" (77.1 cm) - 30" (76.2 cm) models
36-3/8" (92.3 cm) - 36" (91.4 cm) models
width
(74.6 mm)
burner box
15-5/8" (39.6 cm)
blower housing
3-ft. (91.4 cm) long
depth
power supply cable
factory installed.
21" (53.3 cm)
Do Not seal
opening depth
cooktop to countertop.
29-1/2" (74.9 cm) - 30" (76.2 cm) model
35-1/2" (90.2 cm) - 36" (91.4 cm) model
cutout width

Cutout Dimensions

29-1/2" (74.9 cm) - 30" (76.2 cm) model
35-1/2" (90.2 cm) - 36" (91.4 cm) model
2-15/16"
depth
Select required duct cutout
(see Page 4 for exhaust duct
cutout location).
countertop
Install rear
wall junction
box in shaded
area. Darker
shaded area is
preferred.
floor
Minimum base cabinet dimensions —
30" (76.2 cm) base cabinet width
24" (61 cm) base cabinet depth
25" (63.5 cm) countertop depth
Countertop opening dimensions that are shown must
be used. Given dimensions are minimum clearances and
provide required 0" (0 cm) clearance.
New installations — Follow minimum dimensions given.
Replacement installation — Be sure that front edge of
cooktop is at least 1-1/2" (38.1 mm) back from front
edge of countertop.
If cabinet has drawers, drawers will need to be
removed and drawer fronts installed on front of cabinet.
Cutout preparation:
Decorative laminate —
Chamfer all exposed edges to
prevent chipping laminate.
Cut radius corners and file to
smooth edges and to prevent
cracking.
cutout width
Countertop must be
supported within
3" (7.6 cm) of cutout.
5" (12.7 cm)
18"
(45.7 cm)
11" (27.9 cm) 8" (20.3 cm)
21" (53.3 cm)
cutout depth
2" (5.1 cm) minimum
space to front edge of
countertop
3