Further information and explanations are available online: Table of contents 1 Safety ........... 4 7 Programmes ...... 19 1.1 General information.... 4 7.1 Information for test institutes ... 20 1.2 Intended use...... 4 7.2 Favourite ...... 20 1.3 Restriction on user group.. 4 7.3 Intelligent ......
Page 3
20 Transportation, storage and 13.2 Unsuitable detergents ... 31 disposal ........ 52 13.3 Information on detergents .. 31 20.1 Removing the appliance .. 52 13.4 Adding detergent.... 31 20.2 Protect appliance from frost.. 53 14 Tableware ........ 32 20.3 Transporting the appliance ... 53 14.1 Damage to glass and table- 20.4 Disposing of old appliance ...
en Safety 1 Safety Observe the following safety instructions. 1.1 General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2 Intended use Only use this appliance: ¡...
Page 5
Safety en WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating cur- rent only via a properly installed socket with earthing.
en Safety Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. ▶ Check that there is a distance of at least 5 cm between the ap- pliance and installation lines.
Page 7
Safety en Highly caustic alkaline or highly acidic cleaning agents in conjunc- tion with aluminium parts in the interior of the appliance may cause explosions. ▶ Never use highly caustic alkaline or highly acidic cleaning agents, in particular commercial or industrial products, in con- junction with aluminium parts (e.g.
en Safety WARNING ‒ Risk of burns! The blow opening of the Zeolith container becomes hot and can cause burns. ▶ Never touch the blow opening of the Zeolith container. 1.6 Damaged appliance WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. ▶...
Safety en Children may become trapped in the appliance and suffocate. ▶ Use the childproof lock if fitted. ▶ Never let children play with or operate the appliance. WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk.
en Preventing material damage Modified or damaged water hoses Preventing material damage 2 Preventing material may result in material damage and damage to the appliance. damage Never kink, crush, modify or cut ▶ through water hoses. Preventing material damage 2.1 Safe installation Only use the water hoses supplied ▶...
Childproof lock en So as not to scratch the finish on ▶ Environmental protection and saving energy 4 Environmental protec- the appliance, do not use sponges with a rough surface or abrasive tion and saving energy cleaning agents. To prevent corrosion, do not use Environmental protection and saving energy ▶...
en Installation and connection During the drying phase, moisture Sensor set- Description from the interior of the dishwasher is ting stored in the mineral and heat energy Sensitive Adjusts the pro- is released. The heat energy is blown gramme strength for out into the interior of the dishwasher effective removal of with dry air.
Installation and connection en marks on the appliance. These 5.3 Drainage connection marks will disappear after the first Connect your appliance to drainage wash cycle. connection so dirty water is dis- The delivery consists of the following: charged via the wash cycle. ¡...
en Installation and connection 5.5 Electrical connection Connecting the appliance to the electricity supply Notes ¡ Follow the Safety instructions → Page 4. ¡ Please note that the water safety system is only functional if there is a power supply. Insert the non-heating appliance plug of the power cable into the appliance.
Familiarising yourself with your appliance en Familiarising yourself with your appliance 6 Familiarising yourself with your appliance Familiarising yourself with your appliance 6.1 Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with E number and FD num- ber → Page 54.
Page 16
en Familiarising yourself with your appliance Detergent dispenser Add detergent to the detergent dispenser. → "Detergent", Page 30 Bottom basket Bottom basket → Page 24 Dispenser for special salt Add the special salt to the dispenser for special salt. → "Water softening system", Page 26 Lower spray arm The lower spray arm washes the table- ware in the bottom basket.
Familiarising yourself with your appliance en 6.2 Controls You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. With some buttons you can perform different functions. 3 4 5 6 7 8 ON/OFF button and reset Switching on the appliance...
en Familiarising yourself with your appliance Setting buttons Changing the basic settings→ "Chan- ging basic settings", Page 39 Timer programming Setting timer programming → Page 35 Remote Start → "Remote Start ", Page 41 Start button Starting the programme → Page 35 Programme buttons and addi- Programmes tional functions → "Programmes", Page 19 Additional functions → "Additional functions", Page 22...
Page 19
Programmes en Programmes 7 Programmes You can find an overview of the pro- ted. The running time will change if Programmes grammes that can be selected here. the rinse aid system is switched off Different programmes, which can be or rinse aid needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
Programmes en Tip: You can use the Home Connect app to download additional pro- grammes and save them to the button. Saving Favourite on the appliance Press . Press the right programme button. Press the button for the relevant additional function. Press for 3 seconds.
en Additional functions Additional functions 8 Additional functions You can find an overview of the additional functions that can be selected here. Additional functions Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration. You can se- lect certain additional functions depending on the programme.
Features en Press in the levers on the right and Features 9 Features left on the outside of the basket. You can find an overview of the pos- Features sible features of your appliance and how to use them here. These features depend on the model of your appliance.
en Features 9.2 Knife shelf 9.4 Bottom basket Use the shelf for knives and long Arrange pans and plates in the bot- items of cutlery. tom basket. Cutlery basket 9.3 Etagere Large plates up to a diameter of 34 cm can be arranged in the bottom Use the cutlery shelf and space un- basket as shown.
Before using for the first time en 9.5 Folding prongs 9.6 Cutlery basket Use the folding prongs to position Arrange cutlery in the cutlery basket, tableware securely, e.g. plates. always without sorting it and with the sharp points downwards. You can fold the prongs down to po- sition pans, bowls and glasses better.
en Water softening system Press repeatedly until the display To remove any marks from water shows the required setting. or other residues, we recommend you operate the appliance without Note: If you select Initial start-up tableware before using it for the Home Connect here, make further first time.
Water softening system en Note: Set the water hardness determ- ATTENTION! ined on your appliance. Detergent may damage the water softening system. → "Setting the water softening sys- tem", Page 27 Only fill the dispenser of the water ▶ softening system with special dish- With a water hardness of 0 - 8 °E you can dispense with special salt for washer salt.
en Water softening system 11.4 Switching off the water 11.5 Regeneration of the wa- softening system ter softening system If you find the special salt refill indic- In order to obtain fault-free function of ator irritating, e.g. when using com- the water softening system, the appli- bined detergents with salt replace- ance performs regeneration of the ment substances, you can switch the...
Rinse aid system en Close the lid of the dispenser for Rinse aid system 12 Rinse aid system rinse aid. a The lid clicks into position. Rinse aid system 12.1 Rinse aid 12.2 Setting the amount of For optimum drying results, use rinse rinse aid aid.
en Detergent Press repeatedly until the The dosage can be adjusted to the display shows 0. level of soiling. To save the settings, press Liquid detergent approx. 3 seconds. Liquid detergent works faster and is a The rinse aid system is switched recommended for shorter pro- off and the rinse aid refill indicator grammes without PreRinse.
Detergent en 26 °E. With a water hardness above washing and drying results we re- 26 °E you will need to add special commend using special salt from a salt and rinse aid. For the best wash- water hardness of 17 °E. ing and drying results we recom- ¡...
en Tableware Close the lid of the detergent dis- 14.1 Damage to glass and penser. tableware Only put glasses and china in the dishwasher if it is marked as dish- washer-safe by the manufacturer. Avoid damage to glass and table- ware. Cause Recommenda- tion The following...
Tableware en allowing steam to escape and water Cause Recommenda- to leak out around the door. This tion could damage your kitchen units. Highly caustic al- If you are using kaline or highly highly caustic al- acidic cleaning kaline or highly solutions, in par- acidic cleaning ticular commer-...
en Basic operation To save resources, do not pre- 14.3 Removing tableware rinse tableware under running wa- ter. WARNING Observe the following when arran- Risk of injury! ging tableware: Hot tableware can cause burns to the – Put heavily soiled tableware in skin.
Basic operation en The Eco 50° programme is set by Press repeatedly until the default. display shows the right time. The Eco 50° programme is espe- Depending on the setting of the cially environmentally friendly and time display, the end of the pro- ideal for normally soiled tableware.
en Basic operation will help prevent excess pressure building up in the appliance and stop the appliance door bursting open. Open the appliance door carefully. Press . a The programme is saved and the appliance switches off. Press to resume the pro- gramme.
Basic settings en Basic settings 16 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 16.1 Overview of basic settings The basic settings depend on the features of your appliance. Basic setting Selection Description Time setting 00:00 - 24:00 Set the current time.
Page 38
en Basic settings Basic setting Selection Description Water connection Cold water Set cold water or hot water connec- Hot water tion. Only set the appliance to hot water if this can be prepared with little energy and a suitable installation is available, e.g.
Basic settings en Basic setting Selection Description Door Opening Single push ¡ Electric door opening is activated Child-proof lock with the setting "Single push". You Push deactivated open the appliance door by press- ing on the upper middle section of the appliance door once. ¡...
en Home Connect To save the settings, press served when operating the appliance approx. 3 seconds. via the Home Connect app. → "Safety", Page 4 16.3 Setting the time 17.1 Setting up the To open the basic settings, press Home Connect app for approx. 3 seconds. Press repeatedly until the display Install the Home Connect app on shows "Time setting".
Cleaning and servicing en ¡ Security certificate of the Wi-Fi 17.3 Remote Start communication module (to ensure You can use the Home Connect app a secure data connection). to start the appliance with your mo- ¡ The current software and hardware bile device. version of your appliance.
Dishwasher Care and Ma- ance to malfunction. To avoid such chine Cleaner for Dishwashers online faults and reduce odours, we recom- at https://www.neff-home.com/store mend cleaning your appliance at reg- or from customer service. ular intervals. Easy Clean is a programme which re-...
Cleaning and servicing en Running Easy Clean 18.5 Filter system Notes The filter system removes coarse ¡ Run the Easy Clean programme soiling from the dishwashing cycle. without any tableware in the dish- washer. ¡ Only use machine care products and machine cleaners specially designed for dishwashers.
en Cleaning and servicing Pull down the micro filter to re- Insert the filter system into the ap- move. pliance and turn the coarse filter clockwise. Make sure that the arrow mark- ‒ ings match up. Press the locking catches gether and lift the coarse filter out ...
Page 45
Cleaning and servicing en Pull up the lower spray arm to re- move. Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign objects. Insert the lower spray arm. a The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
This will avoid unneces- sary costs. Tip: You can find further information and explanations on troubleshooting on- line by scanning the QR code in the table of contents and on our website www.neff-home.com. WARNING Risk of electric shock! Incorrect repairs are dangerous.
Page 47
Troubleshooting en Fault Cause and troubleshooting E:3200 or indicator Water tap is jammed or furred up. for water supply lights Turn on the water tap. ▶ The flow rate must be at least 10 l/min when the water supply is open. The filters in the water connection of the supply or AquaStop hose are blocked.
Page 48
en Troubleshooting Fault Cause and troubleshooting E:6103 lights up. Wa- Not an appliance fault. Siphon connection is still ter is not drained. closed or the wastewater hose is kinked or blocked. Check the connection to the siphon and open if ne- cessary.
Page 49
Troubleshooting en Fault Cause and troubleshooting All LEDs lit up or Electronics have detected a fault. flashing. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted. If the problem occurs again: Switch off the appliance. ‒ Pull out the mains plug or switch off the fuse in ‒...
Page 50
en Troubleshooting Fault Cause and troubleshooting Remnants of food on Clean the filters. ▶ tableware. → "Cleaning filters", Page 43 Filters are inserted incorrectly and/or not engaged. Insert the filters properly. → "Filter system", Page 43 Engage the filters. Washing programme selected too weak. Select a more intensive washing programme. ▶...
Page 51
Troubleshooting en Fault Cause and troubleshooting Removable streaks Detergent residue is present in the final rinse. Lid of are present on the detergent dispenser is blocked by tableware items glasses, glassware and will not open fully. with a metallic appear- Arrange tableware in the top basket tableware so ance and cutlery.
en Transportation, storage and disposal Insert the pump cover and press 19.1 Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned.
Customer Service en 20.2 Protect appliance from 20.4 Disposing of old appli- frost ance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely.
en Customer Service Customer Service for a period of at 21.2 AQUA-STOP guarantee least 10 years from the date on In addition to warranty claims against which your appliance was placed on the seller under the purchase agree- the market within the European Eco- ment and in addition to our manufac- nomic Area.
Technical specifications en Technical specifications 22 Technical specifications Technical specifications Weight Max.: 60 kg Voltage 220 - 240 V, 50 Hz or 60 Hz Power rating 2000 - 2400 W Fuse 10 - 16 A Water pressure ¡ min. 50 kPa (0.5 bar) ¡ max. 1000 kPa (10 bar) Inlet rate Min. 10 l/min Water temperature Cold water.
Conformity essential requirements and other rel- A detailed Declaration of Conformity evant provisions of Directive can be found online at www.neff- 2014/53/EU. home.com/uk among the additional A detailed RED Declaration of Con- documents on the product page for formity can be found online at your appliance.
Page 57
Declaration of Conformity en The manufacturer, BSH Hausgeräte GmbH deems that it has complied with ¡ provision 5.1-1 of ETSI EN 303 645 v2.1.1 and, where relevant, provision 5.1-2 of ETSI EN 303 645 v2.1.1; ¡ provision 5.2-1 of ETSI EN 303 645 v2.1.1;...
Page 60
BSH Hausgeräte GmbH Carl-Wery-Straße 34 81739 München, GERMANY Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton, Milton Keynes MK12 5PT United Kingdom *9001960761* 9001960761 040723 650 P5...
Need help?
Do you have a question about the S299ZB803E and is the answer not in the manual?
Questions and answers