Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cair Vibe
Summary of Contents for Cair Vibe
- Page 1 Smart Technology, Made to Care Vibe Quick Reference Guide we-cair.com...
-
Page 2: Table Of Contents
Page 9 - Option 3 - Strobe On/Off ● ● Page 10 - Option 4 - Factory Reset ● Page 11 - Option 5 - Turn the Vibe Off ● Page 12 - Option 6 - Exit Configuration Menu ● Page 13 - Switching Off Page 14 - Walk Test Mode ●... -
Page 3: How It Works
The Vibe consists of the main unit, a vibrating pillow pad and a power cable. The Vibe supports up to 24 devices and is easy to program. This guide will explain how to enter the programming menu, which is guided by audible announcements. -
Page 4: Switching On
Port 1. The device can now be connected to the mains power. The Vibe will automatically turn on once connected to power and the power LED on the front of the Vibe will illuminate. The power LED will pulse slowly while the unit is charging and is solid when fully charged. -
Page 5: Adjusting The Volume
Vibe Adjusting the Volume To adjust the volume of the device, press the ‘Next’ button underneath the device. Use the ‘Next’ button to navigate through the sound options. The options “low”, “medium” and “high” will be announced. Once you have arrived at your desired option, the unit will remain at that sound level. -
Page 6: Entering The Configuration Menu
‘Select’ button underneath the device for 5 seconds. After 5 seconds, a beep will be heard; you can now release the button and the Vibe will announce “Configuration menu, press next to continue”. Select ‘Next’ to move through the options. -
Page 7: Option 1 - Add A Sensor
Vibe Option 1 - Add a Sensor The unit will announce “Option 1 - Add Sensor. To add a sensor press select”. If a sensor is to be programmed, press ‘Select’. The announcement will prompt you to activate the sensor. Activate the sensor, then follow the voice commands to select the location and sound. -
Page 8: Option 2 - Remove A Sensor
If a sensor is to be removed, press ‘Select’. The announcement will prompt you to activate the sensor. Activate the sensor, the unit will announce “sensor removed”. The device has now been removed from the Vibe and you will return to the configuration menu. Press ‘Next’ to move to the next option. -
Page 9: Option 3 - Strobe On/Off
Vibe Option 3 - Strobe On/Off The unit will announce “Option 3 - Strobe on/off” (depending on whether it is enabled or disabled). Press ‘Select’ to toggle between the on and off options then press ‘Next’ to move to the next option. -
Page 10: Option 4 - Factory Reset
Vibe Option 4 - Factory Reset The unit will announce “Option 4 - Factory reset. To reset the unit to factory settings, please follow the instructions in the programming guide”. To reset the unit, press ‘Select’ 5 times. The unit will announce “factory reset completed”... -
Page 11: Option 5 - Turn The Vibe Off
Vibe Option 5 - Turn the Vibe Off The unit will announce “Option 5 - Turn the Vibe off. To turn the Vibe off, please follow the instructions in the programming guide”. To turn off the unit, press ‘Select’ 5 times. The unit will announce “shutting down, please wait”. -
Page 12: Option 6 - Exit Configuration Menu
Vibe Option 6 - Exit Configuration Menu The unit will announce “Option 6 - Exit configuration menu”. To exit the menu, press ‘Select’ and the unit will announce “goodbye” and the unit is ready to be used. Smart Technology, Made to Care... -
Page 13: Switching Off
Once the LEDs at the front of the unit have gone off, the unit is safe to disconnect from the mains power. If the Vibe is disconnected from the mains power due to a power cut or before switching off, the unit will announce “Mains power off” repeatedly. To stop this announcement, press the strobe button. -
Page 14: Walk Test Mode
The nominal Walk Test mode will be active for 60 seconds. On reception of a registered sensor, the Vibe will beep and the strobe will flash, confirming that it is within range of the Vibe. To exit Walk Test mode, press the strobe button or let the unit automatically timeout;... -
Page 15: Changing The Protocol
Press ‘Select’ when the Vibe announces the desired protocol number. The Vibe will announce the newly selected protocol number and a beep confirms the protocol menu has been exited. If you do not press ‘Select’, the Vibe will timeout and no changes will be made and a failure beep will be heard. -
Page 16: Fault Conditions
Vibe Fault Conditions When a fault is present, the amber fault LED on the front of the Vibe will illuminate. For more information on the type of fault, briefly press the ‘Select’ button whilst the amber fault LED is illuminated, and the unit is not in use. -
Page 17: Sensor / Trigger Low Battery
LED. The LED will remain lit until the Vibe receives an activation from the sensor after the battery has been addressed, or the unit has been reset. For more information on the trigger/sensor type and ID, briefly press the ‘Select’... -
Page 18: Battery Issues
Vibe Battery Issues If the Vibe is operated in temperatures less than 5°C or above 50°C the unit will not charge the battery. Under these conditions, the amber fault LED will illuminate. This will also happen if the battery is faulty or has been removed. Briefly pressing the ‘Select’... -
Page 19: Mains Failure And Unit Low Battery
To stop this announcement press the strobe button. At a predetermined level the battery will be cut off and the Vibe will be placed in a low power mode that can only be exited by powering the Vibe up again. -
Page 20: Soft Reset
Vibe Soft Reset In the unlikely event that the Vibe becomes unresponsive, press and hold both the ‘Next’ and ‘Select’ buttons for at least 10 seconds, until all the LEDs on the front of the unit illuminate. Then release the buttons and the Vibe will reset. -
Page 21: Smart Technology
Thank you Smart Technology, www.we-cair.com Made to Care 01422 399155 hello@we-cair.com...
Need help?
Do you have a question about the Vibe and is the answer not in the manual?
Questions and answers