MyQ 050DCJCWFSD Replacement

Receiver Logic Board Replacement
Model 050DCJCWFSD
To prevent possible SERIOUS INJURY or DEATH:
• Disconnect ALL electric and battery power BEFORE performing ANY
service or maintenance.
To prevent damage to the receiver logic board, DO NOT touch printed
circuit board of replacement receiver logic board during installation.
ALWAYS wear protective gloves and eye protection when changing the
battery or working around the battery compartment.
WARNING: This product can expose you to chemicals
including lead, which are known to the State of California to
cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada's license-
exempt RSSs. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between
users/bystanders and device.
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help
Before you begin.
Your new myQ serial number is located on the replacement
®
label with your replacement logic board. You will need this new myQ
operator to the network. You will also have a STEP SAVER SETUP label that must be adhered to your
end panel directly under the yellow LEARN button for future identification. This second label indicates
your board has been updated, and a new Product Label should be placed over the current Product
Label. Your product may look different.
SERIAL NUMBER / NUM. DE SÉRIE / NUM. DE SERIE
FCC ID:
IC: 2666A -
IFETEL Cert no.:
MAC ADDRESS / ADRESSE MAC / DIRECCIÓN MAC
CONTAINS / CONTENIR / CONTENER :
PART NO. / NUM. DE PIÈCE / NOM. DE PART: DATE / FECHA: FCC ID:
IC:
1.
Disconnect power.
3.
Remove the battery cover.
Disconnect the battery (optional
accessory). Remove the battery
and set aside (B).
serial number to connect your
®
2.
6.
7.
4.
8.
Label wires for reinstallation.
Disconnect the wires from the
quick connect terminals (C).
5.
Remove the receiver logic board
cover (D).
9.
1
Open the front panel (A).
10.
Adhere the new myQ
number label over the original
label on the logic board cover.
11.
Reconnect the wires to the quick
connect terminals (C).
12.
Install the battery (B) (optional
accessory) and connect the
battery connectors. Install the
battery cover (B).
13.
Reconnect power.
14.
Reprogram the travel and test the
safety reversal system (see pages
2 and 3).
15.
Unplug the wire harnesses from the
Program any accessories you may
receiver logic board (E).
have such as remote controls,
keyless entries, or myQ
Remove the four screws securing
LED Lights (see page 4).
the receiver logic board, remove and
16.
discard (F).
Use the myQ
new myQ
Install the receiver logic board and
your account or Login to your
connect the wire harnesses. Ensure
myQ
®
the wire harnesses are connected
myqbusiness.com) and remove
properly. Route the antenna through
the original myQ
the channel in the cover. Install
operator. Then, follow the steps to
receiver logic board cover.
program the DDO8900W operator
Adhere the STEP SAVER SETUP
in order to relearn it to your myQ
label on the end panel directly below
Business account.
the yellow Learn Button. Adhere the
new Product Label over the existing
product label (D).
serial
®
® Remote
app to add the
®
serial number to
®
Business account (www.
serial # for this
®
®