Table of Contents
Advertisement
Quick Links
IMPORTANT: This manual contains assembly rules, installation steps and guidelines, and use and maintenance
instructions for Isokern XCELUX SEE-THRU Series gas appliances with X-Ventiso-Meridian Fan System. This manual must
become the property of and be reviewed by all current and future users of this product. It is the responsibility of the
distributor, general contractor, and the installer of this product that the instructions in this manual are followed exactly
and, further that the allowed gas log appliance used in this product be installed in strict accordance with the gas log
manufacturer's listing and explicit installation and operation instructions.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warning exactly could
result in serious injury, death, or property damage.
•
Do not store or use gasoline or other
flammable vapors
vicinity of this or any other appliance.
—
WHAT TO DO IFYOU SMELL GAS
•
Do not try to light any appliance.
•
Leave the building immediately.
•
Do not touch any electrical switch; do
not use any phone in your building.
•
Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
•
If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
THESE FIREPLACES ARE DESIGNED FOR USE WITH:
PROPANE (LP) OR NATURAL GAS (NG), ONLY
Contents of this manual may change without prior notification.
and liquids in the
Do not install the Isokern XCELUX SEE-THRU Series Gas
Fireplace in a manufactured home or mobile home or
recreational vehicle.
PFS Report No. F24-349
USA: ANSI Z21.50 - 2019
Issued: February 2025
Revision 000
©2025 Earthcore Industries, LLC
Advertisement
Table of Contents
Related Manuals for EarthCore iSokern XCELUX SEE-THRU 82X48ST
Summary of Contents for EarthCore iSokern XCELUX SEE-THRU 82X48ST
- Page 1 Issued: February 2025 call the fire department. Revision 000 — Installation and service must be performed ©2025 Earthcore Industries, LLC by a qualified installer, service agency or the gas supplier. THESE FIREPLACES ARE DESIGNED FOR USE WITH: PROPANE (LP) OR NATURAL GAS (NG), ONLY...
-
Page 2: Table Of Contents
Registration Card ·································································· 71 X-VENTISO-Meridian Damper –General Information ············ 35 Warranty ················································································ 72 X-VENTISO-Meridian Fan and Adapter – General Information ······························································ 36 ANSI Z21.50 LISTING LABEL The latest revision of this manual may be obtained at the Earthcore website: https://www.earthcore.com/installation- manuals/... -
Page 3: General Information
The Isokern XCELUX SEE-THRU Series and its approved components are safe when installed according to this installation manual and when operated as recommended by the manufacturer. Unless you use Earthcore Industries, LLC approved components tested for this appliance, you may cause a fire hazard or serious injury. Before you begin the installation of this appliance, read these instructions completely. -
Page 4: Safety Instructions
These include pregnant women, people with heart or lung diseases or anemia, people at high altitude or under the influence of alcohol. Earthcore Industries strongly recommends the use of a carbon monoxide detector/alarm device wherever gas fired appliances are in use. - Page 5 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Safety Instructions 11) Do not use the Isokern XCELUX SEE-THRU Series fireplace to cook food or burn paper or other objects. 12) Do not use any solid fuels - wood, coal, paper, cardboard, etc. - in this fireplace. Use only the gas type listed on the fireplace’s burner rating plate.
-
Page 6: Isokern Xcelux See-Thru Series 48" (82X48St)
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Isokern XCELUX SEE-THRU Series 48” (82X48ST) Requires X-VENTISO-Meridian Fan System for proper operation TOP VIEW 12" B-VENT PIPE (12" I.D./13" O.D.) W/ DOWN- DRAFT DIVERTER; X-VENTISO-MERIDIAN FAN SYSTEM REQUIRED. - Page 7 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Isokern AAA Series 48” Components (82X48ST) Requires X-VENTISO-Meridian Fan System for proper operation Component Part# Description Component Part# Description Top Plate Smoke Dome (Qty: 1)
-
Page 8: Isokern Xcelux See-Thru Series 60" (82X60St)
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Isokern XCELUX SEE-THRU Series 60” (82X60ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally Requires X-VENTISO-Meridian Fan System for proper operation 12"... - Page 9 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Isokern XCELUX SEE-THRU Series 60” Components (82X60ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally...
-
Page 10: Isokern Xcelux See-Thru Series 72" (82X72St)
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Isokern XCELUX SEE-THRU Series 72” (82X72ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally Requires X-VENTISO-Meridian Fan System for proper operation 12"... - Page 11 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Isokern XCELUX SEE-THRU Series 72” Components (82X72ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally...
-
Page 12: Isokern Xcelux See-Thru Series 96" (82X96St)
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Isokern XCELUX SEE-THRU Series 96” (82X96ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally... - Page 13 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Isokern XCELUX SEE-THRU Series 96” Components (82X96ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally...
-
Page 14: Isokern Xcelux See-Thru Series 120" (82X120St)
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Isokern XCELUX SEE-THRU Series 120” (82X120ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally... - Page 15 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Isokern XCELUX SEE-THRU Series 120” Components (82X120ST) Steel angle: 6” x 6” x 1/2” cut to span firebox opening. This item is not included in the components and can be sourced locally...
-
Page 16: Required Clearance To Combustibles
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Required Clearance to Combustibles IMPORTANT: “Combustibles” are defined as “normal construction materials” such as: wood framing materials, particle board, mill board, plywood paneling, plywood sub-flooring and wood flooring. -
Page 17: Calculating Flooring Loads
XCELUX SEE-THRU – 96: @ 108-1/4” x 28” = 21.04 sq. ft. • XCELUX SEE-THRU – 120: @ 131-3/4” x 28” = 25.62 sq. ft. Earthcore is not responsible for structural floor support details for this fireplace system. Unless otherwise noted all floor framing drawings in this manual are merely illustrations to indicate the presence of an underlying floor system. -
Page 18: Flooring Systems
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Flooring System NONCOMBUSTIBLE FLOORS XCELUX SEE-THRU Fireplaces must be built upon a concrete support slab with no wood underpinnings. Proper reinforced concrete support slab for fireplace installations may include the following types: 1. - Page 19 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System COMBUSTIBLE FLOOR BLOCK LAYOUT FIGURE 5 FIGURE 6 TABLE 2 TABLE 1 CMU BLOCK ISOKERN MODEL ISOKERN #133 SPACING CMU BLOCK MINIMUM MINIMUMR FRONT QUANTITY...
-
Page 20: Rough Framing Dimensions
For all “raised hearth” construction - even where concrete blocks are used to create the raised platform, it is still mandatory to use the Isokern base plate. Be sure to Earthcore Adhesive the concrete block platform together. All CMU used for base plate support should be rated ASTM 90. -
Page 21: General Assembly Instructions
Earthcore Adhesive is then squeezed from a grout bag onto the contact surfaces of the Isokern components as they are fitted together. NOTE: It is important that a ½” bead of Earthcore Adhesive is piped onto all the components’ contact surfaces, about ½” in from all edges (Figure 9). -
Page 22: Isokern Xcelux See-Thru Installation
1) Apply Earthcore Adhesive to the joints between each baseplate part and ensure to set each base plate in a full bed of Earthcore Adhesive on a level support surface (Figure 11). See page 17 for information regarding the supporting floor system. - Page 23 Earthcore Adhesive already applied to the proper areas on the base plate. 3) Continue assembly of the consecutive courses of the firebox side walls. Apply Earthcore Adhesive to the top of each layer of side wall components before setting the next course in place (Figure 13). Look for some Earthcore Adhesive to squeeze out along the joints of all contact surfaces as a sign that the joint is thoroughly sealed with the approved Earthcore Adhesive.
- Page 24 When properly installed, the angle iron will protrude ½” beyond the front edge of the side wall components (Figure 12). NOTE: It is not necessary to apply Earthcore Adhesive between angle and Isokern sidewall components. NOTE: The steel angle should not be longer than the width of the firebox.
- Page 25 Begin by setting the rear Damper Beam components into place. Next, set the Damper End Blocks into place atop the sidewalls in a bed of Earthcore Adhesive. Be sure to apply Earthcore Adhesive to the contact surfaces of each Damper End Block component where it will meet the front and back damper beam lintel components. Next, set the front Damper Beams into place.
- Page 26 February 2025 Isokern XCELUX SEE-THRU Installation 7) Set the rear smoke dome component(s) across the damper beam in a bed of Earthcore Adhesive and flush with the back face of the rear damper beam lintel. Apply Earthcore Adhesive along the top of the front damper beam along its entire length; bead should be 3” from the front edge.
-
Page 27: Assembled Xcelux See-Thru Units
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Assembled XCELUX SEE-THRU Units Assembled 48” XCELUX SEE-THRU (82X48ST) Assembled 60” XCELUX SEE-THRU (82X60ST) Assembled 72” XCELUX SEE-THRU (82X72ST) - Page 28 Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Assembled XCELUX SEE-THRU Units Assembled 96” XCELUX SEE-THRU (82X96ST) Assembled 120” XCELUX SEE-THRU (82X120ST)
-
Page 29: Combustion Air Kits, Gas & Electrical Line Feed
All XCELUX SEE-THRU fireplaces require a 1-1/2”- 2” hole be drilled into the sidewall for the installation of 3/4” hard-piped gas FIGURE 20 supply to the XL Burner. Ensure all holes are filled with Earthcore Adhesive after installation (Figure 21). ELECTRICAL LINE FEED All XCELUX SEE-THRU fireplaces require a ¾-1”... -
Page 30: B-Vent Metal Chimney - General Information
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 B-Vent Metal Chimney - General Information The XCELUX SEE-THRU Series fireplaces are tested and listed for use only with the specified factory-built metal B-Vent chimney system as detailed in this manual. All XCELUX SEE-THRU fireplace systems require 12” Metal-Fab Type-B Gas Vent Chimney System with Anchor Plate with Down-Draft Diverter. - Page 31 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System B-Vent Metal Chimney - General Information • Connect only one fireplace per chimney. Follow the fireplace safety manual for maximum efficiency and safety. Do not over fire. Any damage to the fireplace or chimney can possibly void the warranty.
-
Page 32: B-Vent Metal Chimney And Components
4 feet 75 feet *Maximum of two 90° offsets. **Maximum offset angle of 90° per offset. ***Sum of all offsets shall not exceed 180° in a run. NOTE: Contact Earthcore representative for total distances exceeding the table minimums / maximums. -
Page 33: General Information
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System X-VENTISO-Meridian Fan System - General Information • IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. • IMPORTANT: INSTALLATION AND MAINTENANCE ARE TO BE PERFORMED ONLY BY QUALIFIED PERSONNEL WHO ARE FAMILIAR WITH LOCAL CODES AND REGULATIONS AND WHO ARE EXPERIENCED WITH THIS TYPE OF EQUIPMENT. -
Page 34: General Information
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 X-VENTISO-Meridian System: Components X-VENTISO 350 Rain XV-350RC X-VENTISO- Collar XV-MERD- Meridian Control CTLR Panel X-VENTISO – Meridian Damper Assembly NOTE: Outer shell/ heat shield is XV-MERD- required for 2”... -
Page 35: X-Ventiso-Meridian Damper -General Information
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System X-VENTISO-Meridian Damper Assembly- General Information The X-VENTISO Meridian Damper Assembly (Figure 22) is a mechanical gas damper that is controlled with the Meridian Control Panel in the XCELUX SEE-THRU fireplace series. The damper closes when the appliance is not in use to prevent conditioned air from escaping through the chimney, and opens right before the appliance burner fires up. -
Page 36: General Information
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 X-VENTISO-Meridian-350 Fan and Adapter - General Information The X-VENTISO-Meridian-350 Fan (Figure 23) is a high temperature exhaust fan that maintains the necessary draft for the XCELUX SEE-THRU series. It has been rated for all high temperature chimney, flue, and grease duct applications up to 2100 CFM, but has specific Molex connections for usage with the Meridian Control Panel. -
Page 37: X-Ventiso-Meridian Control Panel -Installation
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System X-VENTISO-Meridian Control Panel - Installation 1) Determine a suitable location for installation of the Meridian Control Panel. Care should be taken to determine the best location for the Meridian control panel prior to installation. - Page 38 Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 X-VENTISO-Meridian Control Panel - Installation 2) After deciding upon a suitable location for installation of the Meridian Control Panel and ensuring that two 120 VAC/15A outlets have been installed, install the four mounting feet on the back of the Meridian Control Panel enclosure.
-
Page 39: Selecting Horizontal Or Vertical Venting System
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Selecting Horizontal or Vertical Venting System With the XCELUX SEE-THRU fireplace and Meridian Control Panel installed; identify the exterior termination type and location and determine vent routing. Care should be taken to identify obstacles that will require offsets, proper floor and wall protection at flue penetrations, and exterior termination locations/ clearances. -
Page 40: Vent Installation-Vertical Termination Systems
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Vent Installation: Vertical Termination Systems This section covers the installation of vertical termination systems. Vertically terminating chimneys may have the damper mounted either “inline” (located in the middle of the flue run) or at the termination of the flue run. If your installation utilizes a horizontal termination, proceed to section “Vent Installation: Horizontal Termination System”. - Page 41 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Vent Installation: Vertical Termination Systems EXPLODED VIEW FIGURE 32 Vertical Termination with Damper at Termination 1) After mounting of the Anchor Plate and at least 12” of vertical pipe; continue the installation of the chimney by installing sections of 12”...
-
Page 42: Vent Installation-Horizontal Termination Systems
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Vent Installation: Horizontal Termination Systems This section covers the installation of horizontal termination systems. It is important to remember that horizontally terminating systems must utilize the damper “inline” in an accessible location for servicing. The damper cannot be installed at a horizontal termination. - Page 43 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Vent Installation: Horizontal Termination Systems 1) After mounting the Anchor Plate with Down-Draft Diverter and at least one 12” section of B-vent pipe, continue the installation of the chimney by installing sections of 12” B-vent pipe to the location of the XVENTISO-Meridian Damper Assembly.
-
Page 44: Room Pressure Probe
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Vent Installation: Stack Pressure and Room Pressure Probes The vent installation of the XVENTISO-Meridian Fan System is not complete until installation of the required pressure probes. -
Page 45: Firebrick Installation - General Information
Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Firebrick Installation - General Information Earthcore/ Isokern requires the XCELUX SEE-THRU Series fireboxes be lined with a minimum one and one-eighth (1-1/8”) thick firebrick (“Split”) for the sidewalls. One continuous first layer of one and one-eight (1-1/8") thick firebrick (“Split”) to cover entire hearth floor. -
Page 46: Firebrick Installation - Xcelux See-Thru Fireplace
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Firebrick Installation - XCELUX SEE-THRU Fireplace 1) Start the “Split” firebrick at the front edge of the floor of the Isokern firebox, proceeding inward toward the back. Let the floor brick gap approximately 1/2”... -
Page 47: Flush Wall Finish Detail
Isokern firebox. Be sure to fill this gap with Earthcore Adhesive in conjunction with placement of the code required noncombustible finish facing material that is set across the top of the firebox opening. -
Page 48: Clearances To Combustible Trim
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Clearance to Combustible Trim NOTE: “Clearance to Combustible Trim” are those distances required to ensure that a fireplace mantel or facing will not catch fire. In most cases the distances should also be adequate to prevent any discoloration or warping due to heat. -
Page 49: Isoflames Xl Linear Burner - Safety Instructions
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Isoflames XL Linear Burner - Safety Instructions WARNING!!!: This appliance assembly contains burner orifices specifically for the input gas specified on the burner and box, as well as the BTU rating specified in this manual. Modifying or failure to use the factory orifice may cause property damage, personal injury, or loss of life. - Page 50 Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Isoflames XL Linear Burner - Safety Instructions It is imperative that the unit’s control areas, burners and circulation air passages be kept clean. Keep all combustible material, gasoline, and other flammable liquids at a safe distance from the fireplace. Do not use the appliance where these items are used or stored.
- Page 51 These include pregnant women, people with heart or lung diseases or anemia, people at high altitude or under the influence of alcohol. Earthcore Industries strongly recommends the use of a carbon monoxide detector/alarm device wherever gas fired appliances are in use.
-
Page 52: Isoflames Xl Linear Burner - Components List
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Isoflames XL Linear Burner - Components List Top view Bottom view ⑦ ⑧* ⑨* TABLE 6 Item Description Part No. Main Burner Assembly (natural gas) -
Page 53: Isoflames Xl Linear Burner - Specifications
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Isoflames XL Linear Burner - Specifications Burner Specifications Minimum Fireplace Dimension (in) Width Nat. Gas L.P. Gas Burner Model Depth Height Front Rear High High ISFXLB36 17.5... -
Page 54: Gas Line & Valve Box Installation
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Gas Line & Valve Box Installation This appliance must be connected to the gas line in accordance with local codes and/or the National Fuel Gas Code, ANSI Z223.1. -
Page 55: Valve Box & Burner Wiring Diagram
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Valve Box & Burner Wiring Diagram FIGURE 44 FIGURE 45... -
Page 56: Burner Installation
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Burner Installation IMPORTANT: Prior to installation: Shut off main gas supply to fireplace. 1) The ISOFLAMES XL Linear Burner system shall be installed by qualified professional service technician. To ensure proper performance of the appliance the owner’s installation manual must be followed carefully. - Page 57 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Burner Installation BURNER (ISFXLB96 shown) BURNER CAVITY FIGURE 49 FIGURE 50 PILOT ASSEMBLY 3/4” hard pipe must extend 3” TOP BRICK LAYER from sidewall for models ISFXLB36/48/60/72 Within 3”...
- Page 58 Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 36” Burner Connection - ISFXLB36 (N/P) 48” Burner Connection – ISFXLB48 (N/P) ISFXLB48 SECTION 60” Burner Connection – ISFXLB60 (N/P) ISFXLB60 SECTION WARNING: Failure to position the parts in accordance...
- Page 59 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System 72” Burner Connection – ISFXLB72 (N/P) For Isokern XCELUX SEE-THRU 82X96ST ISFXLB72 SECTION 96” Burner Connection – ISFXLB96 (N/P) For Isokern XCELUX SEE-THRU 82X120ST ISFXLB96...
-
Page 60: Remote Control System
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Remote Control System SYNCHRONIZE REMOTE TO CONTROL MODULE FOR THE FIRST TIME Insert the three (3) provided XCELUX batteries into the battery bay in the remote. Correctly align polarity (+/–). - Page 61 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Remote Control System TEMPERATURE INDICATOR DISPLAY With the system in the “OFF” position, press the “Thermostat” Key and the “Mode” Key at the same time (Figure 52). Look at the LCD screen on the Remote to verify that a °C or °F is visible to...
-
Page 62: Burner Lighting Instructions
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Burner Lighting Instructions INSTALLER INSTRUCTIONS It is required that the set of safety instruction labels that have been supplied with the appliance be affixed to the operation and control points of the appliance. -
Page 63: Full System Initialization
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Full System Initialization Once the burner system and the XVENTISO-Meridian Fan System have been wired correctly, and the remote synchronized to the ignition module, a full system check is required. -
Page 64: Air Switch
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Troubleshooting The Meridian Control Panel has 4 main types of alarms. Their name, description, and possible causes can be found in the table below. Possible Causes... - Page 65 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Troubleshooting Earthcore Industries Technical Support: 1-800-642-2920 KW at (817)-393-4029 Probable Issue Possible Solution Cause • Verify power at the outlets • Verify wiring connections No power Mechanical draft system •...
-
Page 66: Glass Media Options
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Glass Media Options EC-BLRK BLACK LAVA PEBBLE • • • • •... -
Page 67: Appendix-A: Xventiso Meridian Connection Diagram
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Appendix A X-VENTISO Meridian Fan System: Connection Diagram Meridian 350 Fan and Meridian Damper Assembly: Adapter: 4-pin Molex to Damper Assembly 3–pin Molex to Fan... -
Page 68: Notes
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 NOTES:... - Page 69 Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System NOTES:...
- Page 70 Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 NOTES:...
-
Page 71: Registration Card
Earthcore Industries February 2025 Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System Registration Card Please tear along dash lines and send to: Earthcore Industries ATTN: Technical Department 6899 Philipps Industrial BLVD Jacksonville, FL 32256 Name:__________________________________________________ Date of Purchase_________________________________________... -
Page 72: Warranty
Earthcore Industries Isokern XCELUX SEE-THRU Linear Open-Front Gas Fireplace with X-Ventiso Fan System February 2025 Warranty & Disclaimer...
Need help?
Do you have a question about the iSokern XCELUX SEE-THRU 82X48ST and is the answer not in the manual?
Questions and answers