Altec Lansing DE9412-8A SPEAKER SYSTEM Dimensions

P
R O F E S S I O N A l
DE9412-8A
FEATURES - THE ALTEC LANSING DIFFERENCE
• 12" Two-Way High Output Speaker System
• High Fidelity 12" / 300mm Duplex
• Bass Horn Cabinet for LF control down to 500 Hz
• Excellent Broadband Efficiency – 102 dB 1 W 1 m
• High Output Performance – 127 dB continuous, 133 dB peak
• Large Format 1.4" Exit Throat HF Driver
• 90˚ x 40˚ Mantaray ™ High Frequency Horn
• Available in Charcoal Grey or White finishes
• Eyebolt suspension hardware included
GENERAL PRODUCT DESCRIPTION
Altec Lansing's new DE9412-8A two-way 12" Duplex
speaker system is designed to provide a high output solution for
reverberant spaces. The DE9412-8A is an excellent choice for
Auditoriums, Performing Arts Centers, Houses of Worship or any
application requiring high output reproduction of both music and speech
program material.
The DE9412-8A features Altec's unique 12" Duplex
component. This Duplex ® "Engine" uses a single magnet structure, with
the high frequency diaphragm on the back of the magnet and the low
frequency voice coil and cone on the front of the structure. The result of
the proximity of the voice coils is a point-source alignment. Altec
Lansing's use of this point-source Duplex
speech intelligibility by minimizing the interference from adjacent
devices that so often occurs in traditional two-way speaker systems.
The 12" Duplex "Engine" is installed in a bass horn cabinet. This
®
trapezoid enclosure provides predictable control in both the horizontal
and vertical planes to below 500 Hz (see polar charts, page 3). The use
of a bass horn cabinet insures that much of the low frequency energy is
kept off the performance area, even when the speakers are flown
overhead.
The DE9412-8A "Engine" is built around Altec's large format 1.4" exit
throat high frequency compression driver, using a 2.8" Pascalite™
aluminum alloy diaphragm. The high frequency energy is fed from the
driver through the center of the magnet structure into a 90˚ x 40˚
Mantaray ® high frequency horn. On the front of the magnet structure,
Altec uses a high efficiency 12" / 300mm cone woofer optimized for bass
horn enclosures.
The paintable trapezoid cabinet is constructed from strong 13-ply birch
plywood, with steel reinforced suspension points. Altec includes the
suspension hardware kit with each speaker. Color choices are charcoal
grey or white, with contrasting cloth covered metal grille. The DE9412-
8A has an internal 1,000 Hz passive network that can be easily switched
over to bi-amp operation. Connectors are barrier strip or Neutrik
Speakon ® connectors. Altec Lansing includes neutral grille cloth with each
subwoofer, allowing you to dye the cloth to integrate the subwoofer
into the surroundings.
For extended low frequency performance, the LF215-4A is a dual
15" / 380mm flyable subwoofer that has the same trapezoid footprint as
the DE9412-8A. Altec Lansing's model 4048A 4-in x 8-out DSP processor
has available presets for a variety of design requirements.
1000 W. Wilshire Blvd., Suite 362 • Oklahoma City, Oklahoma 73116 • Phone: 1-405-848-3108 • Fax: 1-405-848-3217 • www.altecpro.com
® Point-Source Component
® point-source
® point-source speaker
® , or coaxial, design maximizes
FREQUENCY RESPONSE
110 Hz - 15 kHz (±3 dB)
USABLE LOW FREQUENCY LIMIT (-10 dB)
85 Hz
SENSITIVITY 3
Full Range:
Low Frequency Section: 103 dB SPL, (2.83 V input)
High Frequency Section: 108 dB SPL, (2.83 V input)
POWER HANDLING
Full Range:
Low Frequency Section:
High Frequency Section:
MAXIMUM OUTPUT (1 m)
Full Range: 127 dB SPL continuous; 133 dB SPL peak
Low Frequency Section: 126 dB SPL continuous; 132 dB SPL peak
High Frequency Section: 127 dB SPL continuous; 133 dB SPL peak
COVERAGE ANGLES
90 o (horizontal) x 40
DIRECTIVITY FACTOR, Q
13.97
DIRECTIVITY INDEX, Di
11.45 dB
TRANSDUCER COMPONENTS
LF: 1x 12 in. Woofer in a Sealed Mid-Bass Horn (E1012)
HF: 1x 1.4 in. Exit Compression Driver (E1012 on a
Constant Directivity Mantaray
IMPEDANCE 7
Full Range:
Nominal:
Minimum:
Low Frequency:
Nominal:
Minimum:
High Frequency:
Nominal:
Minimum:
CROSSOVER FREQUENCY
Passive LF - HF:
HARMONIC DISTORTION
1% rated power
2nd Harmonic
3rd Harmonic
THD
10% rated power
2nd Harmonic
3rd Harmonic
THD
INPUT CONNECTIONS
2x 4 position barrier strip and 2x NL4
CONTROLS
Lowpass On/Off and Highpass On/Off switches
ENCLOSURE MATERIALS & FINISH
18 mm, 13 ply Birch Plywood Finished with Charcoal Grey
or White Catalyzed Polyurethane
SUSPENSION SYSTEM
Working Load Limit (maximum weight applied to uppermost
mounting point): tbd lbs. (tbd kg)
(12) 3/8 in.-16 Threaded Mounting Suspension Points
(3 each top & bottom and 2 each sides & back)
® DIMENSIONS
27.13 in. (H) x 24.13 in. (W) x 26.13 in. (D) x 10.13 in. (W rear)
689 mm (H) x 613 mm (W) x 664 mm (D) x 257 mm (W rear)
WEIGHT
Net
Shipping
1, 2
1, 2
102 dB SPL
4
300 W continuous; 1,200 W peak
200 W continuous; 800 W peak
75 W continuous; 300 W peak
5
6
o (vertical)
6
6
™ Horn)
8.0 Ω
6.6 Ω at 140 Hz
8.0 Ω
7.3 Ω at 290 Hz
8.0 Ω
6.5 Ω at 3,500 Hz
1,000 Hz
8
0.97%
0.31%
1.01%
2.85%
0.81%
2.80%
9
97 lbs. (44.1 kg)
116 lbs. (52.7 kg)