CALI lipLEDs LLED8600-RPM Installation Manual

Mounting Bracket (LLED8600-RPM-EC)
(LLED8600-RPM-MB)
Aluminum Extrusion
(LLED8600-RPM)
Clear Lens
(LLED8600-RPM-CL)
FEATURES
APPLICATIONS
LAMP TYPE
LENS
VIEWING ANGLE
MOUNTING
WEIGHT
CONSTRUCTION
LENGTH
LISTING
INSTALLATION
ELECTRICAL
DIMMING
MAXIMUM RUN
(Based on 5 Amps)
MAXIMUM RUN
(Based on 4 Amps for Class II)
VOLTAGE
DRIVER
TEMPERATURE RATINGS
PRODUCT INFORMATION
• For accent, decorative, surface, recessed, or pendant lighting
• 24 volts DC for easy and safe installation
• Long life, energy efficient LEDs
• Can be ordered to specific lengths for when exact dimensions are known
Example: 10 x 10'6"
• Plug and light system
• Lead wires are typically 36" long and exit on one end
CALIFORNIA ACCENT LIGHTING, INC.
2820 E. Gretta Lane, Anaheim, CA 92806
ph. 800.921.CALI (2254) | fx. 714.535.7902 | info@calilighting.com | calilighting.com
© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.
2020.2.5 Rev 1
End Cap
3' Power Lead
20/5 Gauge Wire
(LLED8600-PC)
RGBW LightStrip
(LLED8600)
Accent, Decorative, Surface, Recess, Pendant Lighting
Color Changing LEDs: Red, Green, Blue, White
Clear, 50% Semi-Frosted, or 100% Frosted
120°
Mounting Channel or Mounting Clips (Sold Separately)
0.378 lbs per foot
Aluminum Extrusion
Built to Order
Dry, Wet, or IP67 Location
UL2108, CSA C22.2 #9
UL8750, CSA250
Link to Installation Instructions
DMX-512
21' (5.5W)
26' (4.5W)
17' (5.5W)
21' (4.5W)
24VDC
Remote (Sold Separately)
Operating / Startup: -20° to 48°C (-4° to 120°F)
Storage: -40° to 76°C (-40° to 170°F)
LLED8600-RPM
READ ENTIRE GUIDE BEFORE STARTING INSTALLATION
IMPORTANT NOTICE:
VERIFY CORRECT LUMINAIRE WAS RECEIVED WITH
CORRECT COLOR TEMPERATURE, VOLTAGE, AND WATTAGE BEFORE CUTTING OR
INSTALLING. CALI WILL NOT BE RESPONSIBLE IF INCORRECT LUMINAIRE IS INSTALLED.
END VIEW
.94"
.92"
Clear Lens (CL)
50% Semi-Frosted Lens (SF)
100% Frosted Lens (F)
ELECTRICAL
• LipLEDs products require a 24 Volt DC remote electronic transFORMER (TRA-E)
• To calculate transformer size, determine Watts per Foot.
Example: 4.5W per Foot
• Determine Length in Feet.
Example: 14'
• Calculate Load: Multiply Watts per Foot x Length in Feet
Example: 4.5W x 14'= 63W
• Choose a transFORMER from catalog.
Example: TRA80-E
• Determine maximum distance using Maximum Wire Length Table on transformer page.
Example: 63 watts is between 60W and 80W. Using #14 wire, maximum distance is 66' from
transFORMER to first LED
INSTALLATION RECOMMENDATIONS
• LipLEDs LED tape must be mechanically attached directly to mounting surface using mounting
clips or channels.
• Conduit raceway should be sleeved at one end for low voltage wires going to transFORMER.
INSTALLATION TOOLS REQUIRED
• Electric Hammer Drill
• 14.4 to 28 Volt Cordless Drill
• Phillips Bits
• Utility Knife
• Electrical Cord
• Marker
• Wire Stripper
Page 1 of 17
INSTALLATION
Overview
• Long Nose Pliers
• Drill Bits - Concrete or Wood
• Electrical Three Ways
• Safety Glasses
• Measuring Tape
• Chalk Line
lipLEDs
RGBW
™