Vimar WELL-CONTACT PLUS 32131.G Manual

WELL-CONTACT PLUS
32131.G-32133.G-32134.G
32131.G: XT control device KNX standard with 2 push buttons, also configurable as 1 rocker button, LED with status function and visible in darkness with brightness
control, central label to customise symbols, black - 1 front module.
32133.G: XT control device KNX standard with 2 push buttons customisable with labels, also configurable as 1 rocker button, proximity function, labels with status
function and visible in darkness with brightness control, central label to customise symbols, black - 1 front module.
32134.G: XT control device KNX standard with 4 push buttons customisable with labels, proximity function, labels with status function and visible in darkness with
brightness control, black control - 1 front module.
CHARACTERISTICS.
• Power supply: supplied with electrified XT mounting frame art. 32602.x, 32603.x, 32604.x, 32613.x o 32614.x and related node art. 32101
• Maximum absorption from the BUS:
- 32131.x: 7.5 mA
- 32133.x, 32134.x: 12.5 mA
• Red LED and configuration/reset push button
• Operating temperature: -5 °C ÷ +45 °C (indoor use)
• Occupies 1 front module size 30.5 mm
• Brightness on standby levels selectable from the related parameters
• Rear connection to the electrified mounting frame 32602.x, 32603.x, 32604.x, 32613.x or 32614.x
• Protection degree: IP20
2 backlighting push buttons that can also be configured as 1 rocker switch
Central backlighting label
Upper and lower white LED for status indication
Upper and lower label for status indication
4 backlighting push buttons
4 labels for status indication
Proximity function
CONFIGURATION.
Device and related parameter configuration occurs using the ETS software.
All the updated ETS databases can be downloaded from the "Software" section of the www.vimar.com website.
INSTALLATION RULES.
• Installation must be carried out by qualified persons in compliance with the current regulations regarding the installation of electrical equipment in the country where the products are installed.
• The device should be installed on electrified XT mounting frames with:
- 2 modules art. 32602.x (for 2-module mounting box)
- 3 modules art. 32603.x and 32613.x (for 3-module rectangular mounting box)
- 4 modules art. 32604.x and 32614.x (for 4-module rectangular mounting box)
REGULATORY COMPLIANCE.
EMC directive. RoHS directive.
EN IEC 60669-2-1, EN 50491-2, EN IEC 63044, EN IEC 63000 standards.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
WEEE - User information
The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be collected separately from other waste. The user must therefore hand the equipment at the end of its life cycle over to the appropriate municipal centres
for the differentiated collection of electrical and electronic waste. As an alternative to independent management, you can deliver the equipment you want to dispose of free of charge to the distributor when purchasing a new appliance of an equivalent type. You can also
deliver electronic products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to electronics distributors with a sales area of at least 400 m
conscious disposal of the old equipment helps to prevent any possible negative impact on the environment and human health while promoting the practice of reusing and/or recycling materials used in manufacture.
32131-33-34 01 2410
art. art. art.
32131.G 32133.G 32134.G
 
 




 
. Proper sorted waste collection for subsequent recycling, processing and environmentally
2
Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com