Advertisement
Quick Links
I N S T A L L A T I O N I N S T R U C T I O N S
Interactive Flat Panel Over Whiteboard Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
WBM4E
Advertisement
Related Manuals for CHIEF WBM4E
Summary of Contents for CHIEF WBM4E
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Interactive Flat Panel Over Whiteboard Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description WBM4E...
- Page 2 AN ACCESSORY is the secondary Chief • bare 8" thick solid concrete or 8" x 8" x 16" concrete product which is attached to a primary Chief product, and may block wall; or have a component attached or setting on it.
- Page 3 Installation Instructions WBM4E DIMENSIONS DIMENSIONS: INCHES [MILLIMETERS]...
- Page 4 WBM4E Installation Instructions TOOLS REQUIRED FOR INSTALLATION 5/32" 1/8" - wood stud 7/16" (included) 5/16" - concrete, brick 7/16" 1/2" 1/2" PARTS WBM Hardware Kit Lag Bolt and Washer Kit Hardware Kit with Tapping Screws G (4) B (4) F (2)
- Page 5 WBM4E ASSEMBLY AND INSTALLATION WARNING: ELECTRICAL SHOCK, EXPLOSION AND The WBM4E will allow an interactive flat panel display to be FIRE HAZARD! CUTTING OR DRILLING INTO installed over an existing chalkboard/whiteboard. The WBM4E ELECTRICAL CORDS, CABLES OR GAS PLUMBING CAN...
- Page 6 Figure 3 Installing to a Concrete or Concrete Block Wall inner NOTE: The WBM4E may be attached to an 8" concrete wall or hole an 8" x 8" x 16" concrete block wall. Determine the center of the chalkboard/whiteboard. NOTE: The two outside WBM4E wall brackets on the wall assembly (ZZ) must be mounted a maximum of 42"...
- Page 7 Installation Instructions WBM4E Attach one lower wall bracket (Z) to each of the leg NOTE: If necessary, adjust the upper cross bracket so that assemblies using one 1/4-20 x 1/2" flat head cap screw (K) interactive flat panel will be at the desired height.
- Page 8 WBM4E Installation Instructions Attaching Uprights Assembly to Wall Assembly Move the slide nut to the outer most position on the wall (P) x 4 assembly (ZZ). (See Figure 9) IMPORTANT ! : USE TWO PEOPLE FOR LIFTING! The uprights/cross brackets assembly is heavy.
- Page 9 BEFORE completing attachment to wall. NOTE: The lower part of the WBM4E must be attached to the wall using the correct hardware for the wall type. It may be attached to a wood stud wall or to a concrete or concrete block wall.
- Page 10 WBM4E Installation Instructions Holding plastic straps on drywall anchor (DD), pull anchor away from wall until channel rests flush behind wall. (See Figure 15) Slide plastic cap on anchor (DD) towards wall until flange of cap is flush with wall. (See Figure 15)
- Page 11 Installation Instructions WBM4E Adding Covers Open the lower flaps of the wall bracket cover (W) outward. (See Figure 19) Slide the cover downward, hooking the top of the wall bracket covers (W) onto the tabs on top of wall assembly brackets.
- Page 12 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Chief, a products division of Asia Pacific A Office No. 918 on 9/F, Shatin Galleria Milestone AV Technologies 18-24 Shan Mei Street...
Need help?
Do you have a question about the WBM4E and is the answer not in the manual?
Questions and answers