NAD C 326BEE Owner's Manual
Hide thumbs Also See for C 326BEE:

Advertisement

C 326BEE
®
Stereo Integrated Amplifier
Owner's Manual

Advertisement

Table of Contents
loading

Summary of Contents for NAD C 326BEE

  • Page 1 C 326BEE ® Stereo Integrated Amplifier Owner’s Manual...
  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Save theSe inStructionS for later uSe. 14 outdoor antenna grounding - If an outside antenna or cable system follow all warningS and inStructionS marked on the is connected to the product, be sure the antenna or cable system is audio equipment.
  • Page 3 Changes or modifications to this equipment not expressly approved by warning NAD Electronics for compliance could void the user’s authority to operate TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS this equipment.
  • Page 4: Notes On Environmental Protection

    Serial no.: ........NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited...
  • Page 5: Getting Started

    If the unit is not going to be used for some time, disconnect the plug from the AC socket. Should water get into your NAD C 326BEE, shut off the power to the unit and remove the plug from the AC socket. Have the unit inspected by a qualified service technician before attempting to use it again.
  • Page 6: Identification Of Controls

    IDENTIFICATION OF CONTROLS front panel 1 StandbY: With the rear panel POWER switch set to ON position, 4 remote SenSor: Point the SR 8 remote control at the remote press this button to switch ON the C 326BEE from standby mode. sensor and press the buttons.
  • Page 7 (media plaYer): Selects a line-level source connected to the MP 9 tone controlS: The NAD C 326BEE is fitted with BASS and TREBLE sockets as the active input.
  • Page 8: Rear Panel

    Outputs” to this input. as a surround-sound decoder. In normal use, this should be connected to the Main In sockets with the links supplied. To connect your NAD C 326BEE 4 diSc input: Input for additional line level input signals such as CD, to external processor or amplifier sections, remove first these links.
  • Page 9: Power Drive

    In normal use, this should be connected to and “R-” ensuring that the “R+” is connected to the “+” terminal on your PRE OUT sockets with the links supplied. To connect your NAD C 326BEE loudspeaker and the “R-” is connected to the loudspeaker’s “-” terminal.
  • Page 10 Sr 8 remote control USING THE SR 8 REMOTE CONTROL The SR 8 remote control handset handles the key functions of the C 326BEE as well as other NAD Stereo Receivers, Integrated Amplifiers and Preamplifiers. It has additional controls to remotely operate NAD CD Players, AM/FM Tuners and dedicated AM/FM/DAB Tuners.
  • Page 11 Speaker B terminals. Press both buttons to engage both speakers. These buttons are compatible only with specific NAD Receiver or Tuner models and do not apply to the C 326BEE. 10 tone dft: Tone controls are enabled or disabled by pressing this button.
  • Page 12: Troubleshooting

    REFERENCE troubleShooting condition poSSible cauSeS poSSible SolutionS No sound. • Power AC lead unplugged or power not • Check if AC lead is plugged in and power switched ON. switched ON. • Tape Monitor selected. • De-select Tape Monitor mode. • Mute on.
  • Page 13: Overall Specifications

    REFERENCE SpecificationS POWER AMPLIFER SECTION main in, Speaker out Continuous output power into 8 Ω and 4 Ω (Stereo) >50 W (ref. rated THD, 20 Hz-20 kHz, both channels driven) Rated THD (CCIF IMD, DIM 100) <0.009 % (ref. 20 Hz - 20 kHz) Clipping power >65 W (ref.
  • Page 14 ©2008 nad electronicS international a diviSion of lenbrook induStrieS limited All rights reserved. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International C 326BEE Owner’s Manual Issue 1-11/08...

Table of Contents