Subscribe to Our Youtube Channel
Related Manuals for SMART FSE-510-W
Summary of Contents for SMART FSE-510-W
- Page 1 SMART electric height-adjustable floor stand User guide FSE-510-W (FS5-2) Was this document helpful? smarttech.com/docfeedback/171919...
- Page 2 © 2019–2024 SMART Technologies ULC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
- Page 3 Contents Chapter 1 About the stand Features Components Accessories Chapter 2 Assembling the stand Environmental requirements Considerations when assembling the stand Chapter 3 Using the stand Calibrating the stand Moving the stand Raising and lowering the stand Chapter 4 Troubleshooting the stand Resolving general issues Recalibrate the stand Resetting the stand after a surge...
- Page 4 Chapter 1 About the stand Features Components Control panel Accessories Features The SMART electric height-adjustable mobile stand has the following features: Feature Description Powered height With its 26" (65 cm) of electric-powered height adjustment, you can easily adjustment adjust the height of a mounted display with the press of a button.
- Page 5 Chapter 1 About the stand Components The stand consists of the following components: Description Vertical VESA mounting brackets Dual-locking 4” casters [Not shown] Back cover (rear surface) Control panel You can raise and lower the stand with the control panel. It’s located on the right side of the stand, but you can remove and attached it to a mounted display.
- Page 6 The maximum allowable load is 11 lb. (5 kg). Camera bracket Use the camera bracket to mount a compatible camera on the stand. Note The camera bracket is not compatible with 86" (218 cm) SMART Board GX (V2) or 86" (218 cm) SMART Board 6000S (V3) displays. docs.smarttech.com/kb/171919...
- Page 7 Chapter 2 Assembling the stand Environmental requirements Considerations when assembling the stand The stand requires assembly. Consult the SMART electric height-adjustable mobile stand illustrated installation instructions (smarttech.com/kb/171906) included with the stand for assembly instructions. Warning Failure to follow the installation instructions included with the stand could result in personal injury or product damage.
- Page 8 Chapter 2 Assembling the stand Considerations when assembling the stand Warning Two people are required to safely assemble the stand and to mount or remove the display. Lock the casters before installing or working with the display on the stand or adjusting its height. Notes You require ample work space to assemble the stand.
- Page 9 Chapter 3 Using the stand Calibrating the stand Calibrating the stand Moving the stand Raising and lowering the stand Unlocking the height-adjustment safety lock Raising and lowering the stand manually Using the Electric Stand app Setting and using favorite positions Calibrating the stand Calibrating the stand After assembling the stand, you must calibrate it before you start to use it.
- Page 10 Chapter 3 Using the stand 3. Press the Down button and lower the stand to the lowest position. 4. Press the Down button again and hold for five seconds. The stand lowers then bounces up slightly. 5. Release the Down button. Moving the stand Warning Do not move the stand while external cables are connected or when the power is on.
- Page 11 Chapter 3 Using the stand 7. Carefully push the center point of the legs to move the stand. Do not push on the upper part of the stand, as this might cause it to tip over. 8. After the stand is moved, lock the caster brakes and secure the stand in place. 9.
- Page 12 Chapter 3 Using the stand Unlocking the height-adjustment safety lock On FSE-510 stands, the stand’s height-adjustment mechanism locks automatically after 20 seconds of inactivity. Unlock the height-adjustment lock before you raise or lower the stand. To unlock the stand’s height adjustment Press and hold the up and down buttons on the control switch for four seconds.
- Page 13 1. Ensure the stand is connected to the display with a USB cable. 2. On the display, go to where the display’s apps are located. 3. Tap the SMART Electric Stand icon to open the app. When you first open the app the settings cog is red, indicating it's locked 4.
- Page 14 1. Raise or lower the stand to the height you want to set as the favorite position. 2. On the display, go to where the display’s apps are located. 3. Tap the SMART Electric Stand icon to open the app. When the app is opened, the cog wheel is red, showing that it's locked.
- Page 15 Unplug the power cable for the stand. Wait 15 minutes and then reset the stand. Recalibrate the stand (see below) The display doesn’t fit Ensure you’re using the mounting plate supplied with the SMART on the stand. display. If you’re using the stand with a third-party display, ensure the stand supports the display’s dimensions and weight.
- Page 16 Chapter 4 Troubleshooting the stand Recalibrate the stand If the stand lowers but does not move when you try raising it, or if you replace the controller, you may need to calibrate the stand again. To calibrate the stand 1. Connect the stand to a power outlet. 2.
- Page 17 Chapter 4 Troubleshooting the stand Resetting the stand after a surge If the stand loses power from a surge, you must reset it to restore power. 1. Ensure the stand is connected to a power outlet. 2. Push the round, black reset button beside the AC power inlet. Power will be restored to the stand.
- Page 18 Chapter 4 Troubleshooting the stand docs.smarttech.com/kb/171919...
- Page 19 Use the stand only for it’s intended use as described in these instructions. Do not use attachments not recommended by SMART Technologies. Do not operate the stand if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or if it has been dropped into water.
- Page 20 This means while only trained personnel should operate the display, it is not expected that constant supervision will be maintained, and the stand may be left unattended. Use only SMART-supplied mounting hardware or hardware that is designed to properly support the weight of the mounted display and accessories.
- Page 21 Do not use the stand if the power cord is damaged. Replace a damaged power cord only with a new cord provided by SMART Technologies or a qualified service technician. Do not modify or make changes to the control unit or hand switches.
- Page 22 Important information Refer all servicing to qualified service personnel. Servicing is required when the stand has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the stand, the stand has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Page 23 Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier: FS5-2 Responsible Party – U.S. Contact Information SMART Technologies Inc. 2401 4th Ave, 3rd Floor Seattle, WA 98121 compliance@smarttech.com docs.smarttech.com/kb/171919...
- Page 24 2. ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. EU Declaration of Conformity Hereby, SMART Technologies ULC declares that the FS5-2 complies with Directive 2014/30/EU. The full text of the EU and UK declaration of conformity is available at the following Internet address: smarttech.com/compliance...
- Page 25 SMART Technologies smarttech.com/support smarttech.com/contactsupport docs.smarttech.com/kb/171919...
Need help?
Do you have a question about the FSE-510-W and is the answer not in the manual?
Questions and answers