1. Manuals
  2. Brands
  3. Oceaneering Manuals
  4. Marine Equipment
  5. C-Nav Navigator IV
  6. Hardware manual

Oceaneering C-Nav Navigator IV Hardware Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
C-NAV Navigator IV Hardware
Manual
CNAV-MAN-0064
Revision C
®
C-Nav
Positioning Solutions
oceaneering.com/cnav

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C-Nav Navigator IV and is the answer not in the manual?

Questions and answers

Related Manuals for Oceaneering C-Nav Navigator IV

Summary of Contents for Oceaneering C-Nav Navigator IV

  • Page 1 C-NAV Navigator IV Hardware Manual CNAV-MAN-0064 Revision C ® C-Nav Positioning Solutions oceaneering.com/cnav...

  • Page 2: Revision History

    C-Nav, C-Nav3050, C-Tides and C-Monitor are trademarks of Oceaneering International, Inc. “This document is the property of Oceaneering International and may not be used for any purpose unless authorized in writing by Oceaneering and which, upon demand, shall be returned. For any queries, related to Warranty and Limitation of liability, please contact your Accounts Manager for more information.”...

  • Page 3: Table Of Contents

    C-NAV Navigator IV Hardware Manual TABLE OF CONTENTS PURPOSE ............................ 5 INTRODUCTION .......................... 5 Supplied Equipment ........................5 Optional Equipment ........................5 DEFINITIONS ..........................6 Document Conventions ......................... 6 REFERENCES ..........................6 Symbols ............................6 INSTALLATION ..........................7 Installation and Mounting ......................7 General Mounting Instructions ......................
  • Page 4 C-NAV Navigator IV Hardware Manual Computer Specifications ....................... 16 Power Specifications........................16 Physical Dimensions ........................16 User Controls ..........................17 Environmental Considerations ...................... 17 Input / Output Connectors ......................17 SPECIFICATIONS OF ACCESSORIES ..................18 USB Cable ............................ 18 RS-232 COM Module ........................19 APPENDICES..........................

  • Page 5: Purpose

    PURPOSE This manual describes how to install, configure, and operate the C-NaviGator IV Control & Display unit from Oceaneering International, Inc. Sections are organized in a manner that facilitates quick operator orientation. INTRODUCTION The C-NaviGator IV offers the ultimate in performance, convenience, state of the art design, and enduring quality for our customers.

  • Page 6: Definitions

    C-NAV Navigator IV Hardware Manual DEFINITIONS Document Conventions Font Type Used for Arial Plain Text Arial Italic Setting Names ‘Arial Quoted ‘ Setting Values Arial Bold Button Names Arial Bold Italic Menu Items Arial Blue Cross Reference Arial Blue Underline...

  • Page 7: Installation

    C-NAV Navigator IV Hardware Manual INSTALLATION CAUTION: To prevent damage to chassis corners and / or breaking the front glass, please review the illustrations below before handling the units! Installation and Mounting 1. Most of our products are intended for various methods of installation or mounting (panel mounting, bracket mounting, ceiling/wall, console mounting etc.);...

  • Page 8: General Mounting Instructions

    C-NAV Navigator IV Hardware Manual 6. Space necessary for ventilation, for cable inlets, for the operating procedures and for maintenance, must be provided. 7. If the push buttons of the product are not illuminated, an external, dimmable illumination (IEC 60945 Ed.

  • Page 9: Installation Procedures (Panel Cutout/Console Mounting Kit - 15.6 Inch)

    C-NAV Navigator IV Hardware Manual Installation Procedures (Panel Cutout/Console Mounting Kit – 15.6 inch) 5.3.1 Supplied Equipment The HD 16T30 MMC – EN60945 Tested Bracket Kit suitable for console/panel mounting. Suitable for panel thickness min: 3.00 [0.12”] to over 10.00 [0.39”] mm [inch].

  • Page 10: Mounting Bracket Step By Step Instructions

    C-NAV Navigator IV Hardware Manual 5.3.4 Mounting Bracket Step by Step Instructions 1. Locate 4 pcs of Thumb screw and Mounting Socket Nut in separate form as illustrated below. 2. Location both left and right brackets, and assemble the Thumb Screws with the Mounting Socket Nut as illustrated.
  • Page 11 C-NAV Navigator IV Hardware Manual 3. Mount the right bracket on the right rear side of the unit first with 3 x M5 x 12 Countersunk Hex screws as illustrated and fasten it using a Torque Force of 3.75Nm. 4. Tilt the unit 45 degrees to allow the right bracket to enter the cutout first, then tilt it back 45 degree and slide the entire unit into the cutout evenly and carefully.

  • Page 12: Ergonomics

    C-NAV Navigator IV Hardware Manual 6. Finally, in an even way, fasten each of the 4 Thumb Screws to securely fasten the unit to the rear of the Panel Cutout. Ergonomics 1. The front surface of the display glass has an anti-reflective (AR) coating which can be scratched and damaged with improper cleaning.

  • Page 13: Configuring Dc Power In (24Vdc) Housing Connectors

    C-NAV Navigator IV Hardware Manual Configuring DC Power IN (24VDC) Housing Connectors The DC Power IN (24VDC) housing connector (2-pin) plugs into the connector area of the unit. These housing connectors are by factory default mounted on the unit. Below is a brief illustration that might be useful during configuration and installation of such connectors.

  • Page 14: Com4 Serial Input / Output

    C-NAV Navigator IV Hardware Manual COM4 Serial INPUT / OUTPUT Supports RS-232/RS-422 Full Duplex and RS-485 Half Duplex using 1 x D- SUB 9P connector (male). Fasten the cable to the connector using the provided screws on the cable housing itself. Enter BIOS to change RS protocol mode and review Pinout Assignments details for pinning/wiring.

  • Page 15: Operation

    C-NAV Navigator IV Hardware Manual OPERATION User Controls Overview The C-NaviGator IV units feature tactile user controls on the front frame. 7.1.1 Power On/Off + Power LED Status To turn the unit on, verify that the Power LED/Status is illuminated in red (indicates that suitable power is connected) and press the power button and hold until the Power LED/Status changes to green.

  • Page 16: Tft Characteristics

    C-NAV Navigator IV Hardware Manual TFT Characteristics Characteristics Specifications Native Resolution 1920 x 1080 (FHD) Pixel Pitch (RGB) 0.17925 (H) x 0.17925 (V) mm Response Time 35ms (tr+tf) (typical) Contrast Ratio 1500:1 (typical) Light Intensity 400 cd/m (typical) Viewable Angle 85 deg.

  • Page 17: User Controls

    C-NAV Navigator IV Hardware Manual User Controls Behind Front Bezel - Glass Display Control™ (GDC) IP66 • Power On / Off, Brightness Control (- / +), Light Sensor (not visible) • Power LED, ECDIS LED, Buzzer (75-85db) Environmental Considerations Type...

  • Page 18: Specifications Of Accessories

    C-NAV Navigator IV Hardware Manual SPECIFICATIONS OF ACCESSORIES USB Cable USB Cable (Type A plug to Chassis mount Type A receptacle) suitable for installations that feature a secure fastening connection from external equipment with standard Type A ports to the C-NaviGator IV standard USB Type A ports.

  • Page 19: Rs-232 Com Module

    C-NAV Navigator IV Hardware Manual RS-232 COM Module Features: • 2 independent channels (If a card is replaced most operating systems will not change COM port number) • Outputs are short circuit protected Specifications: Internal USB to 2 channel x RS-232 non isolated...

  • Page 20: Appendices

    C-NAV Navigator IV Hardware Manual APPENDICES 10.1 Mechanical Drawings 10.2 Pin Assignments CNAV-MAN-0064 C-Nav DOC-TEM-28-NUM Rev A Uncontrolled copy when printed Revision C Page 20 of 24...
  • Page 21 C-NAV Navigator IV Hardware Manual CNAV-MAN-0064 C-Nav DOC-TEM-28-NUM Rev A Uncontrolled copy when printed Revision C Page 21 of 24...
  • Page 22 C-NAV Navigator IV Hardware Manual CNAV-MAN-0064 C-Nav DOC-TEM-28-NUM Rev A Uncontrolled copy when printed Revision C Page 22 of 24...
  • Page 23 C-NAV Navigator IV Hardware Manual IMPORTANT NOTES: Requires soldering and assembly. It is expected that the technician has experience in electronics, soldering and assembling cables and connectors. If in doubt buy molded off the shelf cabling. CNAV-MAN-0064 C-Nav DOC-TEM-28-NUM Rev A Uncontrolled copy when printed...

  • Page 24: Approvals & Certifications

    C-NAV Navigator IV Hardware Manual 10.3 Approvals & Certifications https://www.hattelandtechnology.com/view_product?id=295%21main_category%3DMarine+&+Offshore=#Type %20Approvals 10.4 Declaration of Conformity CNAV-MAN-0064 C-Nav DOC-TEM-28-NUM Rev A Uncontrolled copy when printed Revision C Page 24 of 24...

Table of Contents