Nordyne 04LD-091A-14-R-DV Installation & Operation Instructions
Nordyne 04LD-091A-14-R-DV Installation & Operation Instructions

Nordyne 04LD-091A-14-R-DV Installation & Operation Instructions

Direct vent oil fired warm air furnaces

Advertisement

Quick Links

Installation & Operation Instructions
Oil Fired Warm Air Furnaces
INFORMATION CONTAINED IN THIS MANUAL PERTAINS TO OIL
FIRED DIRECT VENT FURNACES EQUIPPED WITH A MANUFACTURER
INSTALLED BLOCKED VENT SAFETY CONTROL SYSTEM (PRESSURE
SWITCH).
Do not store or use gasoline or other flammable liquids or vapors in
the vicinity of this, or any other appliance.
NORDYNE INC.
Homeowner Caution
Be sure to keep area around vent terminal free
of snow, ice, and debris
ALL INSTALLATIONS MUST MEET ALL LOCAL,
PROVINCIAL/STATE, AND FEDERAL CODES
WHICH MAY DIFFER FROM THIS MANUAL
Read this manual completely before
installation. These instructions must be
kept with the furnace for future reference.
R
Direct Vent
IMPORTANT
FOR YOUR SAFETY:
P/N# 240005236, Rev. C [03/2010]

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 04LD-091A-14-R-DV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Nordyne 04LD-091A-14-R-DV

  • Page 1 FOR YOUR SAFETY: Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this, or any other appliance. NORDYNE INC. Homeowner Caution Be sure to keep area around vent terminal free of snow, ice, and debris...
  • Page 2: Table Of Contents

    TaBle of ConTenTs 1. DIRECT VENTING OF NORDYNE OIL FIRED FURNACES ..................3 2. VENT TERMINAL LOCATION ..........................3 3. VENT TERMINAL INSTALLATION ........................5 4. VENT TERMINAL RISER KIT ..........................5 5. DIRECT VENT INTAKE AIR PIPE INSTALLATION ....................5 6. VENTING INSTALLATION - DIRECT VENT ......................6 7.
  • Page 3: Direct Venting Of Nordyne Oil Fired Furnaces

    Venting Materials and Fittings: structure. so that the bottom of the vent termination opening is less For components available from Nordyne, please see Table 1. than 1 foot (0.3 m) above any surface that may support snow, ice, or debris.
  • Page 4 figure 2 - Canada : Vent Terminal location figure 3 - United states: Vent Terminal locations...
  • Page 5: Vent Terminal Installation

    IMPORTANT: OUTDOOR AIR FOR COMBUSTION MUST BE 3. VenT TeRminal insTallaTion USED. This applies to the standard Direct Vent Oil Vent Terminal. Select the The oil burners approved for use with ducted outdoor air for location of wall penetration that conforms to the code for exterior combustion is the Beckett AFII.
  • Page 6: Venting Installation - Direct Vent

    WARNING METAL EDGES ARE EXTREMELY SHARP. • DO NOT ENCLOSE VENT. This Double Wall Vent is available in kits, from your NORDYNE • DO NOT ROUTE VENT THROUGH WALLS, FLOORS OR Dealer. See venting components matching guide in this document.
  • Page 7: Operation Of Oil Burners

    Using the chart below, select the appropriate air dial setting accord- figure 8 - Pressure Tubing Connections on Units With Vestibule ing to the required firing rate. This initial setting should be adequate to start the burner. Final adjustments will be required once the burner has been started.
  • Page 8: Blocked Vent Safety Shut Off System

    Technologies 1158-120 have an adjustable fan off time of 2, 3, 4 or 6 The components of this BVS consist of a pressure switch and bypass minutes displayed in the installation manual. The fan off delay time timer. starts when the burner motor is de-energized at the end of a call for Beckett AFII heat.
  • Page 9 where the furnace switch is located, and the switch "on" and figure 11 -Typical appliance Connector with test port "off" positions if not obvious. where the oil shut-off valve from the oil storage tank is located. to keep the area around the vent terminal free of snow, ice, and debris.
  • Page 10: Parts Identification

    TaBle 1 -Z-fleX VenTing ComPonenTs/maTCHing gUide Z-fleX VenTing ComPonenTs/ maTCHing gUide ITEMS AVAILABLE FROM NORDYNE ITEMS PACKED TERMINATION STD or FIELD SUPPLIED WITH FURNACE MODEL YOUR CHOICE of RISER COMPONENTS ITEM ITEM ITEM Oil Vent Terminal 555691 3" x 10' Vent 555688A 5"...
  • Page 11: Afii Burner With Blocked Vent Safety (Bvs) Operation

    afii BURneR WiTH BloCKed VenT safeTy (BVs) oPeRaTion...
  • Page 12 BeCKeTT afii BURneR TRoUBlesHooTing- ConTinUed...
  • Page 13 BeCKeTT afii BURneR TRoUBlesHooTing- ConTinUed...
  • Page 14 BeCKeTT afii BURneR TRoUBlesHooTing- ConTinUed...
  • Page 15: Becket Afii System And General Troubleshooting

    BeCKeT afii sysTem and geneRal TRoUBlesHooTing...
  • Page 16 BeCKeT afii sysTem and geneRal TRoUBlesHooTing - ConTinUed...
  • Page 17 BeCKeT afii sysTem and geneRal TRoUBlesHooTing - ConTinUed...
  • Page 18: Homeowner's Reference Table

    HomeoWneR's RefeRenCe TaBle...
  • Page 19: Notes

    noTes:...
  • Page 20 Installation & Operation Instructions Direct Vent Oil Fired Warm Air Furnaces NORDYNE INC.

This manual is also suitable for:

04hd-091a-14-f-dv

Table of Contents