TRIBIT AquaEase BTS11 - Speaker Manual

Package Contents

Product Illustration

Tips: Support micro SD card up to 32G, support file system format FAT32.

How to Charge the Speaker

Connect the other end of charging cable to a charging adapter and connect the charging cable to the USB-C charging port on the Bluetooth speaker.

Note:
During charging, the indicator light is always on in red.
When the speaker is fully charged, the red indicator light goes off.
When using in wet or watery environment, please plug the silicone plug tightly to avoid water in the charging port.

Button Control

Note: If the Tribit AquaEase Speaker is unable to be powered off due to unknown reasons, you can forcibly turn it off by pressing and holding the power button for 8 seconds and then the speaker will re-start automatically.

2. Bluetooth Connection
   

   	Press and hold the Bluetooth button for 1s	The speaker will automatically enter into Bluetooth pairing mode.	The blue indicator light will flash rapidly.
   	Press twice	Micro SD card playback mode	White light is always on

Tribit AquaEase:

• Automatically re-connects to the last paired device.
• Connects 2 bluetooth devices at the same time.
• Memories 8 bluetooth devices.

Note: When 2 devices are connected to the Tribit AquaEase speaker, device A and device B cannot play simultaneously---only one speaker at a time.

3. Multifunctional Button (MFB)
   

Music Mode	Press once	Play / Pause
	Press twice	Next track
	Press three times	Previous track
	Press and hold for 1 second	Activate voice assistant
Phone Conversation	Press	Answer / end a call
	Press and hold for 1 second	Reject a call
	Press and hold for 1 second (during a call)	Pause the current call and answer an incoming call
	Press (during a three-way calling)	Switch between the 2 calls.
	Press and hold for 1 second (during a three-way calling)	End the call with the caller not in the line.

4. Volume
   

	Press	Increase the volume
	Press and hold	Continuously increase the volume
	Press	Decrease the volume
	Press and hold	Continuously decrease the volume

5. Time setting
   

	Press and hold for 5 second	Enter time settings
	Press	Confirm settings
	Press	Time mode switching

6. Ambient Light
   

   Press

   Switch / Turn off the light effect.

1. Make sure speaker A and speaker B are both are turned on.
2. Press and hold the Bluetooth button on speaker A for 5 seconds to enter the stereo pairing mode. ( Speaker A is the primary speaker.)
3. Press and hold the Bluetooth button on speaker B for 1 seconds to enter the stereo pairing mode. (Note: If this speaker is already in pairing mode, there is no need to perform this operation)
4. When you hear the prompt, "Stereo Mode", the stereo pairing is successful.
   When entering the Stereo Mode, the primary speaker reads, "left Channel" and the secondary speaker reads, "Right Channel".

Note: Stereo mode is only available when there are 2 Tribit AquaEase speakers. And make sure the firmware of both speakers have been upgraded to the latest version through the APP.

8. Reset
   If malfunction occurs, you can try to reset the speaker ( press and hold the volume + button and volume - button at the same time for 5 seconds ) to remedy issues. Once reset, all the old data has been wiped, and you need to pair the speaker to your Bluetooth device anew.
   

Specifications

Customer Service

• An 12-month Warranty
• For more services and information, please Email to support@tribit.com.

Safety Precautions

• Do not place the speaker in a place where it is easy to fall.
• IPX7 is tested under strictly controlled laboratory conditions. Water resistance may diminish over time under daily use. To prevent damage to the product from liquids, do not immerse the product in water.
• Do not disassemble, repair or modify this product by yourself.
• Keep the speaker away from extreme temperatures.
• Do not use the speaker in an outdoor thunderstorm environment.
• Do not use any corrosive cleaners or other chemical solutions to clean the speaker.