Connecting Other Audio Components; Connecting Am/Fm Antennas - Pioneer VSX-1021-K Operating Instructions Manual

Connecting other audio components

This receiver has both digital and analog inputs, allowing you to connect audio components for
playback.
When you set up the receiver you'll need to tell the receiver which input you connected the compo-
nent to (see also The Input Setup menu on page 25 ).
CD-R, MD, DAT, etc.
AUDIO IN
R ANALOG L
HDMI IN 1 VIDEO 1 IN BD IN DVD IN DVR/BDR IN
ASSIGNABLE 1
VIDEO AUDIO
CONTROL
ZONE 2 DVR/BDR CD-R/TAPE ZONE 2
IN
OUT
TV/SAT VIDEO 1
OUT
IN IN OUT
MONITOR
OUT
IR
IN
DVR/
OUT
BDR
OUT IN DVD IN IN
IN 1
(DVD)
ASSIGN
ABLE
IN 2
(DVR/
BDR)
IN
MONITOR
OUT
Y P P TV/SAT VIDEO 1 DVD
B R
COMPONENT VIDEO
! If you're connecting a recorder, connect the analog audio outputs to the analog audio inputs on the
recorder.
! If your turntable has line-level outputs (i.e., it has a built-in phono pre-amp), connect it to the CD
inputs instead.
Select one
AUDIO OUT DIGITAL OUT
ANALOG
R L COAXIAL OPTICAL
LAN (10/100) COAXIAL ASSIGNABLE
OUT
IN IN
IN 1 IN 2
DC OUTPUT 1 2
OPTICAL
for WIRELESS LAN
ASSIGNABLE
(OUTPUT 5 V 0.6 A MAX)
( DVD ) ( CD ) ( TV/SAT ) ( DVR/BDR )
ADAPTER PORT
L
(OUTPUT 5 V
OUT
0.1 A MAX)
R
ANTENNA
CD FM UNBAL
75
L
AM LOOP
SIRIUS A FRONT CENTER SURROUND SURROUND BACK / ZONE 2
IN
R L R L R L (Single)
R
IN
L
IN
R
SUBWOOFER
CAUTION: ATTENTION:
SELEC
SPEAKER IMPEDANCE ENCEINTE D'IMPEDANCE DE
PRE OUT SPEAKERS
Class 2 Wiring SELEC
6 -16 . 6 -16 .

Connecting AM/FM antennas

Connect the AM loop antenna and the FM wire
antenna as shown below. To improve reception
and sound quality, connect external antennas
(see Connecting external antennas on page 19 ).
1 2
3
ANTENNA
5
FM UNBAL
75
AM LOOP
fig. a fig. b fig. c
1 Pull off the protective shields of both
AM antenna wires.
2 Push open the tabs, then insert one
wire fully into each terminal, then release
the tabs to secure the AM antenna wires.
3 Fix the AM loop antenna to the
attached stand.
To fix the stand to the antenna, bend in the
direction indicated by the arrow (fig. a) then clip
the loop onto the stand (fig. b).
! If you plan to mount the AM antenna to a
wall or other surface, secure the stand with
screws (fig. c) before clipping the loop to the
stand. Make sure the reception is clear.
4 Place the AM antenna on a flat
surface and in a direction giving the best
reception.
Connecting your equipment
5 Connect the FM wire antenna into the
FM antenna socket.
For best results, extend the FM antenna fully
and fix to a wall or door frame. Don't drape
loosely or leave coiled up.
Connecting external antennas
To improve FM reception, connect an external
FM antenna to FM UNBAL 75 W.
75 coaxial cable
4
ANTENNA
FM UNBAL
75
AM LOOP
To improve AM reception, connect a 5 m to 6 m
(16 ft. to 20 ft.) length of vinyl-coated wire to the
AM LOOP terminals without disconnecting the
supplied AM loop antenna.
For the best possible reception, suspend hori-
zontally outdoors.
Outdoor antenna
Indoor antenna
(vinyl-coated wire)
ANTENNA
FM UNBAL
75
5 m to 6 m AM LOOP
(16 ft. to 20 ft.)
03
19
En