Table of Contents
Advertisement
Shooting
Special Recording
(continued)
Clip Continuous Rec (continued)
4
Resume recording. (Recording 2)
● Press the [REC] button again to resume recording. The
display changes from STBYC (yellow text) B RECC .
● The card slot status indicator continues to blink in green.
5
Pause recording.
● Press the [REC] button again to pause recording. The
display changes from RECC B STBYC (yellow text).
● The card slot status indicator continues to blink in green.
6
Resume recording. (Recording 3)
● Press the [REC] button again to resume recording. The
display changes from STBYC (yellow text) B RECC .
● The card slot status indicator continues to blink in green.
7
Press and hold the [REC] button or press the user
button that is assigned with Rec Stop to stop the
recording. (A Page 19)
● Recording stops and the display changes from
RECC B STBYC . A clip is generated.
● The card slot status indicator lights up in green.
8
Press the [REC] button again.
● The status display changes from STBYC B RECC and
the card slot status indicator blinks in green.
● A new clip is generated from here.
Memo :
● The following operations cannot be performed while
recording is paused (STBYC, yellow text).
• Clip Review operation (A Page 28)
• Switching SDHC/SDXC card slots
• Switching operation mode (A Page 13)
Note :
● Do not remove the SDHC/SDXC card during recording
(RECC, red text) or recording pause (STBYC, yellow text).
● To remove the SDHC/SDXC card in Clip Continuous
mode, press the user button assigned with Rec Stop or
press and hold the [REC] button, check that STBYC
(white text) is displayed and the card slot status indicator is
lighted in green before you remove the card.
● When the SDHC/SDXC card becomes full during recording,
recording stops and STOP is displayed.
● When the power is turned off during recording or recording
pause, recording stops and power is cut off after a clip is
generated.
● If the power is cut off due to low battery power, a proper clip
may not be generated.
Frame Rec
In normal recording, when the recording stops, the image and
accompanying data from the start till the end of the recording
are recorded as one clip on the SDHC/SDXC card.
In this mode, recording starts with every press of [REC], and
only the specfied number of frames is recorded. The
recording can be written to the media as a single clip until it
is stopped.
Memo :
● Audio cannot be recorded.
● Until a specified amount of recordings is accumulated, the
file will not be written to the media.
● If the specified amount is not reached when recording is
stopped, normal recording is performed and frames are
added to the ending of the clip until the amount is
reached. (Padding)
● After the specified number of frames is recorded and written
to the media, recording will be performed until the same
number is accumulated again.
Press [REC]
(Frame Rec starts)
Press [REC]
Recording resumes
Pause
Pause
Recording of specified number of frames in [Rec Frames]
Actual clip recorded to media
Specified amount of data
1
Set [Rec Mode] to Frame Rec .
● Set [Main Menu]B[Record Set]B[Rec Mode] to Frame
Rec . (A Page 64)
● The status display changes from STBY B STBYF .
2
Set the number of frames to record in [Rec Frames].
Set using [Main Menu]B[Record Set]B[Rec Frames].
(A Page 64)
3
Start recording.
● Press the [REC] button to record only the number of frames
specified in [Rec Frames] and pause.
● The status display changes from
STBYF B RECF B STBYF (yellow text).
● The card slot status indicator blinks in green.
Press and hold [REC]
(Frame Rec stops)
Press [REC]
Recording resumes
Normal recording
(Padding data)
Pause
Advertisement
Table of Contents
