Initial Burn Setup - Pelpro FPP, IPP Owner's Manual

I
NITIAL
IT IS CRITICAL FOR THE CORRECT OPERATION OF YOUR STOVE THAT THE BURN
GRATE, AIR INLET DAMPER, COMBUSTION FAN SPEED, AND
A HIGH QUALITY FIRE
characteristic is a poor quality and inefficient flame. A poor flame produces less heat, increases sooting and may
cause a smoky exhaust. If a poor flame exists for any period of time, clean your stove and exhaust system.
Note: if log option is purchased, do not install until initial setup is complete
START APPLIANCE AS PER LIGHTING
FEED RATE
let stove run for approx. 10 minutes before turning the stove to the # 4 setting (or High), to
4
begin to make fine
and "OFF" for 3-5 seconds. Adjust the
factory sends all units out with the damper wide open to accommodate a wide range of
3
installations and elevations.
AIR INLET DAMPER
2 damper as needed to obtain a fire that is brisk
enough to carry ash out of the grate, but not so
brisk that it carries pellets out as well (known as
"Pop corning"). Normally you should find that the
1
damper will need to be closed two-thirds to three
quarters, but will vary with length of vent run, pellet
quality and elevation. The best way to set this is at
START
the
FEED RATE
When you are pleased with the burn and how the appliance is operating, you
FEED RATE
are now ready to set the board up at LOW setting.
4
Set
approx. 10 minutes before making any adjustments. The AUGER
CYCLE indicator should be "OFF" for approx 9 – 14 seconds
3
between auger turnings (light ON). If "Pop corning" is taking place
at this setting adjust the
2
COMBUSTION FAN SPEED (Draft):
because of prevailing conditions pertinent to your specific
installation, or even different batches of pellet fuel, the
1
COMBUSTION FAN SPEED
decrease the amount of air moving through the grate for the
cleanest burn. Fan speed can be adjusted by adjusting the
START
trim pod
CLOCKWISE to DECREASE
FEED RATE
FUEL RATE:
changed by adjusting the
COUNTER CLOCKWISE
should note the amount of time the light on the
the fuel feed motor is not running). Lengthening the time this light stays "OFF" lowers the fuel feed and
shortening the "OFF" time increases the fuel feed . Factory Setting #1 light "OFF" is approx. 9-11 seconds,
#4 light "OFF" is 3-4 seconds.
Can
adian Comfort Industries
Copyright 2004
A
PPLIANCE
1 & 4 FUEL RATE BE SET CORRECTLY!
should burn with a brisk, yellow flame.
adjustments. AUGER CYCLE indicator
:
FUEL SETTING #4.
FUEL RATE to #1 or LOW
COMBUSTION FAN SPEED.
COUNTER CLOCKWISE to INCREASE
Fuel rate at the Lowest (number 1) and highest (number 4) settings can be
#1 or #4 TRIM PODS located on the control panel. To
and to LOWER turn CLOCKWISE. To assist in knowing what changes you made, you
AUGER CYCLE
V04
www.pelprostoves.com
B
URN
A flame exhibiting a lazy, orange or sooty
INSTRUCTIONS,
AIR INLET DAMPER. This will have to be set, as the
Slide open or close
setting. Again let this burn for
In a few instances
may be adjusted to increase or
the speed and
the speed of the combustion fan.
stays "OFF". (Note: The light stays "off" when ever
28
S
ETUP
should be lit "ON" for 3 seconds
Rubber
Stove Back Panel
GrometT
Decrease
FINE TUNE ADJUSTMENTS
1
FAN
INCREASE fuel rate turn trimmer
PELPRO OWNERS MANUAL
Dansons Group Inc.
Air Inlet
Slide Rod
Right Hand
Side Panel
Increase
4
FAN