Casio XW-P1 User Manual page 44

Sounding Arpeggio Phrases Automatically
Menu Layer
1 2
Step Edit >Ent
TYPE
NOTE
VELO
6.
After the TYPE, NOTE, and VELO settings are the way you want, press
menu screen.
7. bq
Use the up (q) and down (w) buttons to move the item selection cursor (0) to "Parameter", and
bq
then press ENTER.
8. bo
Use the dial or the
• The table below shows the contents of the parameter editing menu.
Menu Layer
1 2
Parameter >Ent
Max Step
Step Size
NoteLngth
Groove
Grv.Type
Velocity
Hold Pedal
9.
After you finish arpeggio parameter editing, save it as described below.
7
• Press WRITE to display the screen for saving arpeggio data. Save the arpeggio by performing the same operation as
that for saving a user tone (page E-12).
• For information about deleting data you saved, see page E-71.
■ Saving Arpeggio Data on an External Device
• Memory card (page E-73)
• Computer (page E-79)
E-42
Specifies the relative position in the arpeggio pattern where the keyboard notes will play starting
from the lowest note played (which is L1).
• If the number of keys pressed is less than the number of configured type (L) settings (i.e. if you
press only three keyboard keys for an arpeggio pattern that includes settings for L1 through L6),
the arpeggio pattern will repeat, playing the keyboard key notes one octave higher.
• At any point the above causes the range of one higher octave to be exceeded, arpeggio play will
return to the L1 note automatically.
Specifies the relative position in the arpeggio pattern where the keyboard notes will play starting
from the highest note played (which is U1).
• If the number of keys pressed is less than the number of configured type (U) settings (i.e. if you
press only three keyboard keys for an arpeggio pattern that includes settings for U1 through
U6), the arpeggio pattern will repeat, playing the keyboard key notes one octave lower.
• At any point the above causes the range of one lower octave to be exceeded, arpeggio play will
return to the U1 note automatically.
Specifies how many of the notes played on the keyboard, starting from the highest note played,
should be played simultaneously.
• When the number of keys pressed is less than the polyphony (P) value specified here, only the
notes that are played are sounded.
Shifts the notes produced by pressing keys in semitone steps.
Changes the velocity of pressed keys.
bq
minus (–) and plus (+) buttons to change the parameter settings.
Description
Maximum step. Can be edited only by step type.
Step size. Specifies the note length between steps.
Note length. Specifies the length of the note that is sounded as
a percentage of the step size. (100% for the same length as
the original, 50% for half the original.)
Groove. Specifies the timing of the off-beat step. (50% for
even. Larger values increase the length of the first half of the
note.)
Groove type. Specifies the note length when the Groove
setting is anything besides 50%.
Velocity. Specifies the velocity of an input arpeggio. Specifying
KeyOn inputs a velocity value in accordance with the degree
of key pressure applied.
Hold pedal. Specifies on/off switching for hold used by a pedal. On, Off
Description
1 to 16
2, 6,
1 to 100%
10 to 90%
Norml: Plays back at the actual percentage of the
step length.
Short: Adjusts to a short step in accordance with the
step.
KeyOn, 1 to 127
L1 to L8
U1 to U8
P2 to P5
–24 to +24
–64 to +63
bq
EXIT to return to the arpeggio
Settings
, 7, , 8
Settings