Advertisement
MOTORIZED FLEXSHADE
VERY LARGE MOTORIZED SHADING SYSTEM
Overview - Components
1 Headbox
2 Mounting brackets
3 Endcaps
4 Hem bar
FlexShade XL Angled Headbox
(Ceiling Mount shown)
5"
(127mm)
5"
(127mm)
SHADE
HEIGHT
Read and understand all warnings
Contents
Overview - Components .......................................................................................1
PLEASE READ - Safety Information ....................................................................2
Section 1 - Brackets .............................................................................................3
Section 2 - Endcaps ..............................................................................................3
Section 1 - Bottom Access Panel Installation/Removal .................................4
/
"
5
16
(8mm)
CAUTION
(Page 2 of this document)
XL
®
2
1
4
FlexShade XL Curved Headbox
(Surface /Wall Mount Shown)
(127mm)
SHADE
HEIGHT
before beginning installation.
Section 2 - Bottom Access Panel Installation/Removal .................................4
Section ?? - Wiring Diagrams ..............................................................................7
Section ?? - Dimensions.......................................................................................8
INSTRUCTIONS
INSTALLATION & OPERATION
3
5"
(127mm)
5"
If you have any difficulties installing or servicing your
Motorized FlexShade XL, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2024 All Rights Reserved
TOOLS
REQUIRED
Pencil
Power Drill
Tape Measure
Level
Hardware
(by Others)
|
FORM: FS_XL_Inst19
Advertisement
Table of Contents
Related Manuals for Draper MOTORIZED FLEXSHADE XL
Summary of Contents for Draper MOTORIZED FLEXSHADE XL
- Page 1 Section 1 - Bottom Access Panel Installation/Removal .........4 If you have any difficulties installing or servicing your Motorized FlexShade XL, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 FORM: FS_XL_Inst19 ©...
- Page 2 Window covering products manufactured by Draper, when properly installed, should require no operational maintenance or lubrication. Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy water.
-
Page 3: Section 1 - Preparation For Installation
MOTORIZED FLEXSHADE ® page 3 of 6 Section 1 - Preparation for Installation MOUNTING Figure 1 Caution: Before mounting shades, verify measurements on label provided with shade, and ensure unit is installed at BRACKET correct width. 1¾” 1. Make sure mounting surface is strong enough to hold FlexShade XL. (45mm) Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions. - Page 4 MOTORIZED FLEXSHADE ® page 4 of 6 ROOM SIDE Section 8 - Limit Switch Adjustments Front Section 8.1 - Standard and Quiet Motors (All procedures shown are for Standard Roll. Invert orientation for Reverse Roll) Back Section 8.1.1- Push Button Limits Caution: PUSH BUTTON LIMITS Standard right-hand...
-
Page 5: Section 9 - Dimensions
MOTORIZED FLEXSHADE ® page 5 of 6 Section 9 - Dimensions 4” 4” (102mm) (102mm) Shade Width Fabric Width 5” (127mm) 5” (127mm) ” (22mm) Section 10 - Mounting Bracket Dimensions Exterior FlexShade XL Ceiling Mounting Bracket Exterior FlexShade XL Wall Mounting Bracket 6"... -
Page 6: Section 9 - Electrical Connections
Please Note: All operating switches should be “off” before power is connected. Please Note: For low voltage wiring requirements, Draper recommends consulting with a professional low voltage electrical contractor. It is very important that shielded and stranded CAT 5 cable be used to prevent any electrical interference.
Need help?
Do you have a question about the MOTORIZED FLEXSHADE XL and is the answer not in the manual?
Questions and answers