TECO L510s Quick Setup Manual

This is a quick set-up guide for configuring the Teco
L510s for either of the following control requirements:
This is a quick set-up guide for configuring the Teco
• Motor Parameter Setup
L510s for either of the following control requirements:
• Start/stop control – Keypad, External Switch
• Motor Parameter Setup
or PLC etc...
This is a quick set-up guide for configuring the Teco L510s for either of the following control requirements:
Start/stop control – Keypad, External Switch
•
• Wiring Diagram - 2-wire & 3 wire start/ stop
• Motor Parameter Setup
or PLC etc...
operation
• Start/stop control – Keypad, External Switch or PLC etc
• Wiring Diagram - 2-wire & 3 wire start/ stop
• Speed/frequency control – Keypad, Pot on
• Wiring Diagram - 2-wire & 3 wire start/ stop operation
operation
Keypad, External Pot.
• Speed/frequency control – Keypad, Pot on Keypad, External Pot
Speed/frequency control – Keypad, Pot on
•
Highlighted in the table below are the main parameter
Keypad, External Pot.
Highlighted in the table below are the main parameter groups that are invloved in this list of control requirements.
groups that are invloved in this list of control
Highlighted in the table below are the main parameter
requirements.
groups that are invloved in this list of control
PARAMENTER GROUP No.
requirements.
Group 00
Group 01
Group 02
Group 03
Group 04
Group 05
Group 06
Group 07
Group 08
Group 09
Group 10
Group 11
Group 12
Motor Parameter Setup:
Group 13
Motor Parameter Setup:
Short Press MODE to change to Parameter Group
Motor Parameter Setup:
Short Press MODE to change to Parameter Group
Short press </ENT to move
across, press , to
change parameter number.
Short press </ENT to move
across, press , to
change parameter number.
Hold </ENT
2s
Motor Rated Current (A)
(Defaul
t)
Hold </ENT
2s
Motor Rated Current (A)
Hold </ENT
2s
Motor Rated Speed (RPM)
(Defaul
(Defaul
t)
t)c
Hold </ENT
2s
Hold </ENT
Motor Rated Speed (RPM)
2s
Motor Rated Power (kW)
(Defaul
(Defaul )
t)c
t)c
Hold </ENT
2s
Motor Rated Power (kW)
Hold </ENT
2s
)
(Defaul Motor Rated Frequency (Hz)
t)c
(Defaul
t)c
Hold </ENT
2s
Motor Rated Frequency (Hz)
(Defaul
t)c
For additional support, please contact us at:
TECO VSD Tech Support: 0433 215 642
Email Address: vsdsupport@teco.com.au
TECO L510s - Quick Set-up Guide
TECO L510s - Quick Set-up Guide
TECO Australia and New Zealand
Description
Basic parameter
V/F Pattern selections and set up
Motor parameters
Multi function digital Inputs/Outputs
Analog signal inputs / Analog output
Present frequency selections
Auto Run (auto sequencer) function
Start/Stop command setup
Drive and motor protection
Communication function setup
PID function setup
Performance control functions
Digital display & monitor functions
Inspector and maintenance function
Hold </ENT
2s to save.
Hold </ENT
2s to save.
Hold </ENT
2s to save.
Hold </ENT
Hold </ENT
2s to save.
2s to save.
Hold </ENT
2s to save.
Hold </ENT
2s to save.
Hold </ENT
2s to save.
Page - 1
TECO L510s - QUICK SET-UP GUIDE
Start/Stop Control – Keypad,
External Switch:
Start/Stop Control – Keypad,
Start/Stop Control – Keypad, External Switch:
External Switch:
Short Press MODE to change to Parameter Group
Short Press MODE to change to Parameter Group
Short press </ENT to move
across, press , to
change parameter number.
Short press </ENT to move
across, press , to
change parameter number.
Hold </ENT 2s
(Default)
Hold </ENT
Hold </ENT 2s
(Default)
(Defaul
Keypad External Switch
Hold </ENT
2s
(Defaul
Keypad External Switch
t)
Hold </ENT
2s to save.
Hold </ENT
Hold </ENT
2s to save.
2s to save.
Hold </ENT 2s
(Default)
Hold </ENT 2s
2s
(Default)
(Default) Communication
t)
(Default) Communication
Hold </ENT
Hold </ENT
2s to save.
2s to save.
Hold </ENT
2s to save.