Download Print this page

Operation - Black & Decker HSMC1321 Instruction Manual

Hide thumbs Also See for HSMC1321:

Advertisement

Available languages

Available languages

use (Figure F). If the seal is missing or damaged contact your
nearest authorized repair agent. Do not use the appliance.

CAUTION: Ensure that the hose is securely fastened
before using the handheld steam cleaner.
Attaching Other Accessories to the Hose (Fig. G)
1. For accessories other than the steam nozzle, align the
 33 
lugs 
on the hose with the recesses on the accessory.
2. Press the accessory onto the hose and twist clockwise until
the accessory is fully seated and clicks into place.
Attaching Steam Jet Nozzle (Fig. H)
 34 
1. Press in the clips 
 on the steam jet nozzle 
2. Align the two keys on the inside flange of the steam jet
nozzle with the two slots at the end of the hose
3. Firmly press the steam jet nozzle onto the hose such that
it is fully seated, and release the clips.
4. To remove, press the clips and pull the steam jet nozzle
away from the hose.

WARNING: Inspect the seal on the steam nozzle of
the hose before each use (Figure H). If the seal is missing or
damaged contact your nearest authorized repair agent. Do
not use the appliance.

CAUTION: Ensure that the hose and/or steam nozzle is
securely fastened before using the handheld steam cleaner.
Attaching Pad to Squeegee (Fig. F, G, I)

WARNING: Burn hazard. Do not use the squeegee and
pad on clothes that are being worn.

CAUTION: Wait until steam cleaner cools down to attach
or remove the squeegee pad (approximately five minutes).
NOTE: The squeegee pad 
window squeegee.
NOTE: To ensure the steamer is safe for a fabric, first test it in an
inconspicuous area of the item you are to use it on.
 11 
1. Attach the hose 
to the steam cleaner as described
for Figure F.
 36 
2. Attach the squeegee 
Figure G.
3. Hook the squeegee pad 
squeegee and stretch it to the other side of the squeegee as
shown in Figure I. Ensure the pad fully covers the squeegee.
Removing Accessories from the Hose
• For accessories other than the steam nozzle, turn
handheld steamer off, unplug, and allow to cool down.
Then twist accessory counterclockwise then pull away from
the hose.
Attaching the Carpet Glider (Fig. J)
1. Place carpet glider on the floor.
2. Lightly press the steam mop with attached cleaning
 21 
pad 
down onto the carpet glider 
into place.
Removing the Carpet Glider

CAUTION: Always wear suitable shoes when changing
the carpet glider on your steam mop. Do not wear slippers or
open‑toed footwear.
1. Return the handle tube 
the steam mop to 'OFF', and unplug.
2. Wait until steam mop cools down (approximately five
minutes). Place the front of your shoe onto the carpet glider
 37 
removal tab 
and press down firmly.
3. Lift the steam mop up off the carpet glider.
 24 
 11 
 35 
works only with the
to the hose as described for
 35 
around one side of the
 28 
until it clicks
 6 
to the upright position, turn
Filling the Water Tank (Fig. K)
NOTICE: Fill the water tank with regular tap water.
NOTICE: In areas of very hard water, the use of deionized
water is recommended.

WARNING: Do not overfill the tank.
1. Ensure that the appliance is switched off and the power
cord is disconnected from the power supply.
2. Open the filler cap 
3. Fill the water tank with water.
4. Close the filler cap.
.
NOTICE: Always empty the water tank after use.
NOTICE: Fill the water tank with clean tap water (do not use
.
any additives or chemicals).

WARNING: When filling, detach from main unit and
maintain in a horizontal position.

WARNING: Your water tank has a 17 fl oz (0.5 liter)
capacity. Do not overfill the tank.
NOTICE: Ensure the filler cap is firmly secured.

OPERATION


CAUTION: FOR FLOOR AND HANDHELD USE ONLY;
DO NOT USE THE UNIT UPSIDE DOWN.
Switching ON/OFF (Fig. A)
NOTICE: It takes approximately 15 seconds for the steam
mop to heat up.
• To switch the appliance on, press the ON/OFF button 
turn the SmartSelect™ dial 
• To switch the appliance off, turn the SmartSelect™ dial to
off, then press the ON/OFF button.
NOTICE: Never leave the steam mop in one spot on any
surface for any period of time. Do not store with a wet
pad as this can damage your floor. Always place the steam
mop with the handle tube 
stationary and make sure the steam mop is turned off and
unplugged when not in use.
NOTICE: Always empty the water tank after use.
SmartSelect
The steam mop is equipped with a SmartSelect™ steam
 3 
dial 
which shows various hard surface cleaning
applications. To change the application, turn the
SmartSelect™ steam dial until the correct operating mode
for your particular hard floor surface is selected.
NOTICE: The dial has an "off" position. There will be no steam
flow when the dial is turned to this position.
NOTICE: For garments and carpet, set the dial to the Wood/
Laminate setting.
NOTICE: Do not use on any unsealed hard floor surfaces.
Additionally, on surfaces that have been treated with wax
or some no‑wax floors, the sheen may be removed by the
heat and steam action. It is always recommended to test an
isolated area of the surface to be cleaned before proceeding.
We also recommend that you check the use and care
instructions from the floor manufacturer.
 4 
by pulling up (Figure K).
 3 
 to the desired setting.
 6 
in the upright position when
TM
Dial (Fig. A)
ENGLiSh
 1 
, then
9

Advertisement

loading
Need help?

Need help?

Do you have a question about the HSMC1321 and is the answer not in the manual?

Questions and answers

This manual is also suitable for:

Hsmc1361Hsmc1361sgpkHsmc1361sgpHsmc1321apb