Related Manuals for AEG JSV5520
Summary of Contents for AEG JSV5520
- Page 1 Favorit 45250Vi Dishwasher Posudomoe^naq ma[ina Instruction booklet Rukowodstwo po \kspluatacii...
- Page 2 Save these instructions and make sure they remain with the dish- washer if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety.
- Page 4 822 61 10-10...
-
Page 5: Table Of Contents
Instruction book ..........4-23 Safety information .............4 Disposal ................6 General information............7 Description of the appliance..........8 Prior to using for the first time.........10 Programme chart ............14 Loading the dishes............16 Using the appliance ............17 Care and cleaning............20 In the event of a fault ............22 Service ..............24-25... -
Page 6: Instruction Book
”Installation” section. Before installing the appliance, ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating can also be found on the rating plate. - Page 7 In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains, remove the fuse.
-
Page 8: Disposal
Disposal of old appliances At the end of the appliance's useful life, disconnect the electrical plug from the power supply, then cut the electrical lead at the point where it enters the appliance. Make quite sure that children will not be able to... -
Page 9: General Information
Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use. - Some types of glass can become dull after a large number of washes. Make sure you always buy articles that are dishwasher safe. -
Page 10: Description Of The Appliance
Instruction book Description of the appliance 1 Spray arm 2 Coarse filter/microfilter 3 Fine filter 4 Detergent dispenser 5 Rinse aid dispenser 6 Salt container... -
Page 11: The Control Panel
Combination buttons ”A”: In addition to selecting a programme, you can press these two buttons to adjust the setting of the water softener, switch off the buzzer and rinse aid dispenser. Control lamps: Shows that • Refilling of salt is necessary •... -
Page 12: Prior To Using For The First Time
Prior to using for the first time Adjusting the water softener To prevent the build up of lime on the dishes and in the dishwasher, the dishes must be washed with soft water i.e. water with a low lime content. -
Page 13: Filling With Salt For The Water Softener
Prior to filling with salt, please check each time that you really do have a packet of dishwasher salt in your hand. 1. Unscrew the filler cap to the salt container anticlockwise. -
Page 14: Switching The Rinse Aid Dispenser Off
Instruction book Filling the rinse aid Use of rinse aid will result in cleaner and faster drying of the load, since it helps water and soil to run off. Too much rinse aid may result in streakiness, too little may cause white spots. -
Page 15: Adjusting Rinse Aid Dosing
Adjust the dosage setting according to the hardness of the water. You can set the dosage between 1 - 6, equivalent to 1 - 6 ml rinse aid. Factory setting is 1. Begin at the lowest dosage setting and increase if necessary by turning the setting arrow with e.g. -
Page 16: Programme Chart
Water: 9 litres 7 litres 1) Noise levels vary at different stages of the wash programme as at some programme stages the dishes are washed more energetically so that they will be cleaned more thoroughly. 2) The consumption figures were determined under standard conditions. - Page 17 Instruction book Coffee cups, All types of dishes delicate items • normaly soiled • lightly soiled • lightly soiled 35 MIN GLASS 50° 50° 40° Pre-rinse Washing Washing Washing Rinse Rinse Rinse Final rinse Final rinse Final rinse Drying 150 minutes...
-
Page 18: Loading The Dishes
Instruction book Loading the dishes Always place glasses, cups and bowls upside down. Incline deep dishes (soup plates etc.) so that the water can run off when drying. Make sure that the dishes do not rest against each other. This is particularly important in regard to the cutlery basket - nested spoons, etc. -
Page 19: Using The Appliance
3. Put the correct amount of detergent into the detergent dispenser and close the dispenser lid. 4. Press in the On/Off button. All programme indicator lamps are lit. 5. Press in the required programme button (see programme chart). All other programme indicator lamps goes out. -
Page 20: Cancelling The Drying Phase
Instruction book Cancelling the drying phase In case you do not want to wait until the drying phase is completed, you can cancel it by open the door. The drying phase is now cancelled. Setting the delay start The programme start can be delayed by 3, 6 or 9 hours. - Page 21 2. Leave the dishes in the dishwasher for approx. 15 minutes after the end of the programme so that they dry better and cool down. 3. Check the filters to see if they need to be cleaned when the dish- washer has finished the programme.
-
Page 22: Care And Cleaning
Spray arm (1) It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. If the spray arm needs cleaning, unscrew the nut anti-clockwise, remove the washer and lift off the spray arm. - Page 23 If the dishwasher is placed in an environment where the temperature some- times fall below 0° C, there is a risk that the small amount of water which remains inside the parts of the dishwasher will freeze and damage it.
-
Page 24: In The Event Of A Fault
Instruction book In the event of a fault Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. Fault Check The programme will not Is the door closed properly? start. - Page 25 Is the dishwasher level? close. If the indicator lamp for the ended programme cycle is flashing, it is possible that you can solve the problem your self. When the problem is solved, press in the On/Off button and the programme continues. If the problem occurs again, contact your local service centre.
-
Page 26: Service
”In the event of a fault” because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. -
Page 27: Information For Test Centres
Service Information for test centres The salt container and rinse aid dispenser shall be filled in accordance with this instruction manual. Before conducting the measurements the dishwasher shall be operated for one or two complete cycles using detergent and a clean load. -
Page 28: Position- And Connection Instructions
230 V ~ 50 Hz Fuse 10 A Heating element 1100 W Power rating 1180 W This appliance complies with the following E.E.C. directives: – 73/23/EEC, dated 19.02.1973 – low-voltage directive. – 89/336/EEC, dated 03.05.1989 (incl. amendment – 92/31/EEC) – directive on electromagnetic compatibility. -
Page 29: Installation
Position- and connection instructions Installation Unpacking Check the dishwasher for transport damage. Never connect a damaged machine. In the case of damage, please contact your retailer. Keep all packaging away from children. Check that the following accessories are supplied with the dishwasher when you unpack it: –... - Page 30 Position- and connection instructions Position The machine is basically designed to be built into a cupboard. It is vital to ensure that the machine is positioned on a horizontal level in order for it to function properly and so that the door can be properly closed.
- Page 31 (A) diameter 35 mm, predrill the holes for the hinge brackets (B) diameter 2 mm and guide rods (C) dia- meter 5 mm. Weight of the door including handle max. 4,7 kg to get good balance.
-
Page 32: Preparing The Outer Door
Position- and connection instructions Preparing the outer door Screw the guide rods and hinges on the door into place using the predrilled holes. Mount plate Before installing the dishwasher and adjusting the door onto the cupboard, put the mount plate into its correct position on the shelf. -
Page 33: Mounting The Outer Door
2 screws provided. Fitting protective and cap strips In order to fill the gap between the cup- board and the dishwasher and to protect the cupboard above from any steam that comes out of the washer, a self-adhesive... -
Page 34: Mounting The Dishwasher
2 screws, with the washers between. 2. Put the spacers provided at the sides of the machine and screw the machine into place in the cupboard. Check that there is a space between the cupboard frame and the wooden door when it is shut. -
Page 35: Water Inlet
These features are according to current water technical safety regulations. The temperature of the water supply should not exceed 65° C and the pressure should be between 80-1000 kPa (0,8 - 10 bar). It is important to have a tap or stopcock, positioned close to the dishwasher and with easy access. -
Page 36: Water Drainage
Position- and connection instructions Water drainage To protect the dishwasher against water damage it is equipped with a water safety system. In the event of a fault the drainpump starts automatically and the remaining water inside the dishwasher is pumped out. - Page 37 Electrical connection The dishwasher is supplied with a lead and electrical plug for connection to a 230 V earthed wall socket, which should be easily accessible and protected by a 10 A fuse. Before any work is carried out on the dishwasher, it must be isolated from the electric mains supply, for example by removing the plug from the wall socket.