Fly Wing Bell-206L Scale Helicopter Quick Start Manual
  1. Manuals
  2. Brands
  3. Fly Wing Manuals
  4. Toy
  5. Bell-206L Scale Helicopter
  6. Quick start manual

Fly Wing Bell-206L Scale Helicopter Quick Start Manual

Hide thumbs

Advertisement

Table of Contents

Bell-206L Scale Helicopter
Smart He l i
uic Start Guide
V2.5

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Bell-206L Scale Helicopter and is the answer not in the manual?

Questions and answers

Related Manuals for Fly Wing Bell-206L Scale Helicopter

Summary of Contents for Fly Wing Bell-206L Scale Helicopter

  • Page 1 Bell-206L Scale Helicopter Smart He l i uic Start Guide V2.5...

  • Page 2: Flight Environment Requirements

    1.Check whether the main blades ,tail blades, helicopter body and landing skids are damaged or distorted, please replace them with the genuine Fly Wing RC parts. 2.Check whether the flight control linkages and fuselage are fixed firmly, and whether the GPS unit is correctly fixed on the helicopter tail boom (horizontally placed, straight line behind the main mast ) H1 Unit is fixed firmly on the double sided foam pad either at the front or at the back of the main mast.
  • Page 3 and other functions will not be available. lease make a reasonable judgment on the flight condition by naked eye observation, and set the corresponding flight and return altitude according to the flight environment. Disclaimer： The remote control model is not a toy. This product is o u tab e to adults o a e e e e ce...
  • Page 4 About transmitter using FS-i6S transmitter which is 2.4GHz, 1km* control Bell-206L distance Please don't touch your transmitter menu it has been factory set, if the setting is changed incorrectly, you will not be able to start the helicopter. * For the first time, you need to connect a computer to activate this function The maximum communication distance is measured in the experimental environment for reference only.

  • Page 5: Install Canopy

    ssemble Airwolf Scale Helicopter 1.Insert blade Insert the blade as shown in the figure until there is slight resistance when the blade folds. 2. Install canopy Insert the canopy pin into the body hole, pull the pull rod backwards, install the upper hatch cover, and push the pull rod pin back into the hole in the front of the canopy.
  • Page 6 Operate Airwolf Scale Helicopter 1. Starting transmitter Hold the two power buttons at the same time for two seconds to turn on the transmitter. If the transmitter shows any warning please flip the motor run switch to top position motor off action then turn the mode switch to position.
  • Page 7 . eady to fly lease place the helicopter in a flat open outdoor area with user facing the tail. mode unlock take off take mode as an example ● 1 Turn the transmitter motor run switch ove the helicopter to the outdoor open to stop position, dial mode switch to environment without trees and buildings, and GPS, and the H1 light is flashing yellow.

  • Page 8: Home Mode

    nlock take off in mode take mode as an example ● ove the helicopter to the outdoor open ial the motor run switch to stop position, dial environment without trees and buildings. ower the mode switch to position, on, and the H1 flight control light is solid blue. nlock as shown in the figure and hold for uring the blue light is flashing, ial motor switch stick to run position,and the helicopter motor will...
  • Page 9 sers can increase or decrease the return voltage according to the flight demand, or turn off the low • power return function. It is recommended to set the return voltage between 3.65 V and 3.75 V, which will affect the actual flight duration and return distance When the transmitter signal is normal, the transmitter can be used to control the landing position during the return landing.

  • Page 10: Compass Calibration

    6. Compass calibration ompass is easy to be disturbed by strong electric field, strong magnetic field and strong electromagnetic field, which will lead to abnormal compass and even cause flight accidents. egular calibration can make the compass works at its best. alibration precautions 1.
  • Page 11 7. . Model 1/Model 2 change 1、When the helicopter is powered off, press hort press the wrench icon to enter the and hold the screen lock icon for about menu seconds to unlock the screen nter the Y T menu and click sticks mode elect the corresponding mode on the right side of the screen and press the arrow in the upper left corner to return...
  • Page 12 FLY WING Youtobe Facebook 宜 F lywingRC. com WWW. 一...

Table of Contents