Viewing The Touch Screen - Yamaha CL3 Owner's Manual

Touch screen

Viewing the touch screen

The touch screen of the CL series indicates the following
information, and is broadly divided into two areas.
Main area
Function access area
1
Selected channel
This field indicates the
number, name, icon and
channel color of the channel
that is currently selected for
operation. You can also use
this field as a button to switch
channels. Pressing the left
half will select the preceding
channel, and pressing the
right half will select the next
channel.
2
Time
This area indicates the
current time.
3
Status Indicator
This area indicates the
current unit status. Normally
it indicates the name of the
user who is currently logged
in (i.e., is authenticated and
able to operate the system).
If the oscillator or talkback is enabled, this area will
indicate "OSC" or "TALKBACK. " If cue monitor is on,
this area will indicate "CUE. " In this case, the type of
signal being cue-monitored (IN/OUT/DCA/KEY
IN/EFFECT) is shown in the upper part of the cue
meter. Furthermore, this area indicates "ACCESS"
while the unit is accessing a USB flash drive attached
to the USB connector. In ALTERNATE mode, it
indicates "ALT. " During audio file playback, it
indicates "PLAY. " During recording to a USB flash
drive, it indicates "REC. "
NOTE
Do not disconnect the USB flash drive while this area is
indicating "ACCESS." Doing so may damage the data on
the USB flash drive.
20
Function access
area
1
2
4
3
5
6
7 8
9
j k
l
Owner's Manual
4
HELP
This button is used to display on-line Help in the main
area. To view the on-line Help, first you must load the
Help file from a USB flash drive.
5
SENDS ON FADER
Press this button to switch to SENDS ON FADER
mode, where you can use the faders of the top panel to
adjust the MIX/MATRIX send level. During this time,
the function access area of the touch screen will switch
to a screen that enables you to select the
send-destination MIX/MATRIX bus.
6
CH JOB (Channel Job)
Press this button to switch to CH JOB mode, where
you can make settings for channel grouping and
linking. During this time, the function access area of
the touch screen will switch to a screen that enables
you to select the function you want to operate.
7
RACK
When you press this button, the VIRTUAL RACK
screen will appear in the main area, allowing you to
edit the I/O rack, external head amps, GEQ and effect
settings. The VIRTUAL RACK screen consists of six
rack sections: GEQ 1–8, GEQ 9–16, EFFECT,
PREMIUM, I/O RACK, and EXTERNAL HA.
8
MONITOR
When you press this button, the MONITOR screen
will appear in the main area, allowing you to edit the
monitor or oscillator settings.
9
METER
Level meters that monitor the level of the STEREO
bus (L/R), MONO bus (M), and cue signal (CUE).
When you press this field, the METER screen will
appear in the main area. If you press part of the CUE
meters when the cue monitor is on, the cue monitor
will be canceled (equivalent to CUE CLEAR).
0
SETUP
When you press this button, the SETUP screen will
appear in the main area, allowing you to make basic
system settings and user-specific settings.
A
RECORDER
When you press this button, the recorder screen will
appear in the main area, allowing you to operate and
make settings of the recorder function for recording
and playing back audio files.
B
SCENE
This area indicates the number and title of the scene
that was last stored or recalled. An "R" symbol is
displayed for read-only scenes, and a lock icon is
displayed for write-protected scenes. If you edit the
parameters from their last stored or recalled state, an
"E" symbol will appear in the lower right. When you
press this field, the SCENE LIST screen will appear in
the main area, allowing you to store or recall scenes.
7
When you press a button
corresponding screen, the button will be highlighted. In
this state, pressing the button once again will return either
to the most recently recalled SELECTED CHANNEL
VIEW screen or the OVERVIEW screen.
B
through to access the