HIKVISION P Series Quick Start Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Controller
  5. P Series
  6. Quick start manual

HIKVISION P Series Quick Start Manual

Led controller
Hide thumbs
Table of Contents

Advertisement

Quick Links

LED Controller (P Series)
Quick Start Guide
0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HIKVISION P Series

Summary of Contents for HIKVISION P Series

  • Page 1 LED Controller (P Series) Quick Start Guide...
  • Page 2 Document, which may include licenses obtained from third parties. ● Any part of the Document, including text, pictures, graphics, etc., belongs to Hikvision. No part of this Document may be excerpted, copied, translated, or modified in whole or in part by any means without written permission.
  • Page 3 LED Controller (P Series) • Quick Start Guide HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
  • Page 4 LED Controller (P Series) • Quick Start Guide Preface Applicable Models This manual is applicable to the P series LED controller. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text.
  • Page 5 LED Controller (P Series) • Quick Start Guide  Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.  Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas.

  • Page 6: Table Of Contents

    LED Controller (P Series) • Quick Start Guide TABLE OF CONTENTS Chapter 1 Introduction ....................... 1 Overview ................................1 Appearance ................................1 1.2.1 Front Panel ..............................1 1.2.2 Rear Panel ..............................4 Chapter 2 Installation ....................... 10 Safety Precautions .............................. 10 Install the Device in the Rack ..........................

  • Page 7: Chapter 1 Introduction

    LED Controller (P Series) • Quick Start Guide Chapter 1 Introduction Overview The LED controller (hereinafter referred to as the device) can be used with the full-color display units to achieve the seamless jointing of the video wall in any dimensions. It is applicable to the meeting rooms, studios, gyms, airports, banks, advertisements, family cinemas, etc.
  • Page 8 LED Controller (P Series) • Quick Start Guide No. Name Description mode, the device is running normally.  Slow flashing: The system is in soft shutdown process.  On: The device is in self-test picture mode.  Off: A device exception occurs or the device is not powered on.
  • Page 9 LED Controller (P Series) • Quick Start Guide No. Name Description You can use the broadcast software to export the program file to the USB flash drive and insert the USB flash drive into the device to play the programs.

  • Page 10: Rear Panel

    LED Controller (P Series) • Quick Start Guide No. Name Description  Normal status: Press the button to increase brightness. Button +  Self-test status: Press the button to switch to the next self-test picture. Signal souce button Press and hold the button to enter or exit self-test.
  • Page 11 LED Controller (P Series) • Quick Start Guide Rear Panel of 2K LED Controller with 6 Outputs No. Name Description Debugging network port (LAN) Connects to the network cable for device debugging. Output network port (DATA Connects to the LED display.
  • Page 12 LED Controller (P Series) • Quick Start Guide No. Name Description controller to the network port of a computer. After the LED controller is activated, remove the network cable connecting the LED controller and computer, and then connect the computer and LED controller to the same wireless network.
  • Page 13 LED Controller (P Series) • Quick Start Guide No. Name Description  Connects to the DVI port of the display device to check the signal source status. DVI loop output port (LOOP)  Connects to the DVI IN port of the next LED controller for signal loop output.
  • Page 14 LED Controller (P Series) • Quick Start Guide No. Name Description Connect to the GENLOCK OUT port of the next LED controller. Sync input port (GENLOCK IN) This port is plug-and-play. No configuration is required before using this port. IR input port (IR IN) Connects to the IR device.
  • Page 15 LED Controller (P Series) • Quick Start Guide No. Name Description RS-485 port for central control Connects to the RS-485 port of central control device. device To use the hot spot function of the LED controller for the first time: Connect a Wi-Fi antenna to the WIFI AP 2 port, and then enable and configure hot spot on the network configuration page of the web client.

  • Page 16: Chapter 2 Installation

    LED Controller (P Series) • Quick Start Guide Chapter 2 Installation Safety Precautions As a high-precision, system-level electronic product, the device should be installed and maintained by professionals. In order to avoid personal and property injury, please read the safety precautions in this section carefully before installation.

  • Page 17: Install The Device In The Rack

    LED Controller (P Series) • Quick Start Guide  Do not use the working ground together with the grounding device or lightning protection grounding device of power equipment, and keep the two as far away as possible.  Keep away from high-power radio transmitters, radar transmitters, and high-frequency and high-current equipment.
  • Page 18 LED Controller (P Series) • Quick Start Guide Install the Mounting Brackets Use two TWM3 × 6 pan-head screws (4) to install two connecting brackets (3) to the inner sides of two devices with the FRONT surface facing forward. Install the Connecting Brackets 1...
  • Page 19 LED Controller (P Series) • Quick Start Guide Secure the Connecting Brackets 1 Prepare the clip nuts and M5 screws or M6 screws (6) to secure two devices (5) to the rack post (7). Secure Devices to the Rack...
  • Page 20 LED Controller (P Series) • Quick Start Guide If you install multiple layers of devices in the rack, keep at least one rack post hole between each layer of devices. Using Connecting Bracket 2 Use two KM3 × 6 countersunk screws (1) to install one mounting bracket (2) to the left side of the device front panel.

  • Page 21: Connect Cables

    LED Controller (P Series) • Quick Start Guide Secure the Connecting Brackets 2 Prepare the clip nuts and M5 screws or M6 screws to secure two devices to the rack post. If you install multiple layers of devices in the rack, keep at least one rack post hole between each layer of devices.
  • Page 22 LED Controller (P Series) • Quick Start Guide Connect the other end of the grounding cable to the grounding terminal of the device (1) and tighten the screw. Connect the Grounding Cable to the Grounding Row Without Grounding Row Drive an angle steel (4) or steel pipe into the ground (3) of at least 0.5 m.

  • Page 23: Connect The Network Cable

    LED Controller (P Series) • Quick Start Guide The device is connected to the network through networking equipment such as switches. It is recommended to use the CAT 6 Ethernet cable to connect the network port of the device to the network port of the networking equipment.

  • Page 24: Chapter 3 Display Control

    LED Controller (P Series) • Quick Start Guide Chapter 3 Display Control Use the Client  Use the LED batch controller client and LED controller to control the LED display. 1) To download the LED batch controller client, visit https://www.hikvision.com/en/support/tools/hitools/cl47c33f8903447a02/...

  • Page 25: (Optional) Use The Remote Control

    LED Controller (P Series) • Quick Start Guide (Optional) Use the Remote Control You can purchase the remote control to control the LED display. Use the LED batch controller client or the web page of the LED controller to lighten the display.
  • Page 26 LED Controller (P Series) • Quick Start Guide Remote Control Button Description No. Name Description  If the display is on, press the button to enter the sleep mode of the display. Power button  If the display is off, press the button to lighten the display.
  • Page 27 UD37430B-E...

This manual is also suitable for:

Ds-dt60p-02hi04noDs-dt60p-02hi06noDs-dt60p-02hdi20no/uDs-dt60p-02hdi12no/u

Table of Contents