Table of Contents
Advertisement
10
About the Remote Setup menu
The Remote Setup mode is set by pressing the number button while pressing RCU SETUP. The different items
on the Remote Setup menu are described below. For their setting procedures, refer to the explanations for the
respective items.
Setting
What it does
Preset codes can be set for the various input functions. The remote control codes of a number of other
Preset recall
devices (including products of other brands) are preset in the remote control to allow these devices to be
operated. See
Selecting preset codes directly
If the desired operations cannot be performed even though you have set the preset codes, the remote control
Code learning
signals of other devices can be learned directly. See
page
84.
This is a setting for changing only the remote control unit's operation screen, without changing the receiver's
Direct function
input, when the remote control unit's input function buttons are pressed. This is convenient for using the
remote control unit for devices not connected to the receiver. See
This function is used to erase remote control codes that have been learned. Codes learned for the different
Erase learning
input functions can be erased individually. See
The backlight lighting pattern can be selected from among four modes, in consideration of convenience and
Back light
battery service life. See
Setting the backlight mode
This is a function for resetting preset codes that have been set. Key resetting can be done for individual input
Reset function
functions. See
Erasing all learnt settings that are in one input function
This is a function for resetting all remote control unit settings you have made to the defaults set upon ship-
All reset
ment from the factory. See
Resetting the remote control settings
If you have multiple Pioneer receivers, amplifiers, etc., this setting can be used to prevent other units from
Change RC
operating simultaneously when the remote control unit is operated. See
mode
83.
Note
! You can cancel or exit any of the steps by pressing RCU SETUP.
! After one minute of inactivity, the remote automatically exits the operation.
Operating multiple receivers
Up to four receivers can be operated discretely using this receiver's remote control when using multiple receiv-
ers, provided they are of the same model as this receiver. The receiver to be operated is switched by inputting the
preset code to set the remote control setting.
! Set the remote modes on the receivers before using this function (see
102).
1
Press and hold RCU SETUP, then press '4' for three seconds.
Release the button after the LED flashes once. The LED continues to flash.
! To cancel the preset setup mode press RCU SETUP.
2
Press the number button for the receiver ("Receiver 1" to "Receiver 4") you wish to
operate.
For example, to operate "Receiver 2", press '2'.
If the LED lights for one second and continues to flash, the setting has been successfully completed.
When the preset code is input, the LED flashes three times to indicate that the setting has failed.
on
page
83.
Programming signals from other remote controls
Direct function
on
page
85.
Erasing one of the remote control button settings
on
page
on
page
85.
on
page
85.
on
page
86.
Operating multiple receivers
on
Remote Control Mode Setup
on
page
Setting the remote to control other components
Most components can be assigned to one of the input function buttons (such as DVD or CD) using the compo-
nent's manufacturer preset code stored in the remote.
However, there are cases where only certain functions may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote control will not work for the model that you are using.
If you can't find a preset code that matches the component you want to control, you can still teach the remote
individual commands from another remote control (see
page
84).
! With the TV CONTROL buttons, the TV can be operated regardless of the input set for the remote control's
operation mode. When using one TV set, we recommend assigning the same TV's preset codes to the
on
TV CONTROL INPUT button and the TV button. When using two TV sets, for better convenience assign the TV
connected to the MONITOR OUT terminals to the TV CONTROL INPUT button, the other TV to the TV button.
! Devices may be assigned to the following input function buttons.
84.
page
Selecting preset codes directly
1
Press and hold RCU SETUP, then press '1' for three seconds.
Release the button after the LED flashes once. The LED continues to flash.
! To cancel the preset setup mode press RCU SETUP.
2
Press the input function button for the component you want to control.
To assign the preset codes of the TV to be operated with the TV CONTROL function, press the TV CONTROL
INPUT button.
The LED blinks once and flashes continuously.
3
Use the number buttons to enter the 4-digit preset code.
See
Preset code list
on
page
128.
If the LED lights for one second and continues to flash, the setting has been successfully completed.
When the preset code is fully input, the LED flashes three times to indicate that the setting has failed. If this hap-
pens, enter the 4-digit preset code again.
83
Controlling the rest of your system
Programming signals from other remote controls
RECEIVER
ALL ZONE STBY
SOURCE
DISCRETE ON
RCU SETUP
BDR
BD
DVD
DVR
HDMI
TV
CD
NET
ADPT
USB
CBL
iPod
SAT
MHL
TUNER
RECEIVER
INPUT SELECT
STATUS
VOLUME
INPUT
TV CONTROL
CH
VOL
MUTE
on
Advertisement
Table of Contents
