Related Manuals for Dogtra EF-3500
Summary of Contents for Dogtra EF-3500
- Page 1 E-FENCE 3500 UNDERGROUND E-FENCE SYSTEM Owner's Manual Please read this manual thoroughly before operating the Dogtra E-FENCE 3500.
-
Page 2: Table Of Contents
CONTENTS OVERVIEW ......................MAIN FEATURES OF THE E-FENCE 3500 ............. SAFETY FEATURES ....................PACKAGE CONTENTS ..................DESCRIPTION OF TRANSMITTER PARTS ............DESCRIPTION OF RECEIVER PARTS ............... RECEIVER FITTING ....................ADAPTOR ........................ CHARGING THE RECEIVER ................CHANGING THE CONTACT POINT LENGTH ..........TESTING THE SYSTEM PRIOR TO INSTALLATION ........ -
Page 3: Overview
OVERVIEW The Dogtra E-FENCE 3500 system gives you the ability to allow your dog the freedom he wants within your specified boundaries. Dogtra’s containment system contains your dog without the use of conventional fencing that can be chewed through, jumped over or dug under. -
Page 4: Main Features Of The E-Fence 3500
· 2-hour rapid charge lithium polymer batteries SAFETY FEATURES · Dogtra’s E-FENCE 3500 system uses state-of-the-art microcomputer technology. The receiver has an automatic control that limits the stimulation to eight seconds. · Dogtra’s filtering system prevents accidental activation from outside sources other than your transmitter. -
Page 5: Package Contents
PACKAGE CONTENTS Wall-Mount Receiver 20ga Underground Transmitter Fence Wire (500 feet) Boundary Training Owner's Training Flags (50 each bundle) Manual Book Transmitter Ground Wire Receiver Power Adaptor (green) Charger (5-volt 1A) (24-volt 500mA) Test Lamp Plastic Anchors Transmitter (2 ea.) Mounting Screws (2 ea.) Wire Splices... -
Page 6: Description Of Transmitter Parts
DESCRIPTION OF TRANSMITTER PARTS On/Off Boundary Wire Indicator Light Continuity Light Field Width Adjustment Knob On/Off & Function Selection Switch Connector for Ground Wire Power Jack Boundary Wire Connector Tabs E-FENCE 3500 Transmitter... - Page 7 On/Off & Function Selection Switch The On/Off & Function Selection Switch has three functions. When the toggle switch is in the up position, the unit will give the dog a Pager vibration followed by stimulation. When the toggle switch is in the down position, only a Pager vibration occurs (no stimulation).
- Page 8 Boundary Wire Continuity Light When the wires are connected properly, the boundary wire continuity light will be on. In the event that the E-FENCE 3500 wire becomes damaged or disconnected, the light will automatically turn off and the warning beep will sound. Wire Connector Tabs The easy-to-use push-release wire connectors let you instantly connect...
- Page 9 Power Jack Plug the 120-volt adaptor into a 120-volt wall outlet and insert the adaptor plug into the power jack of the transmitter. Wall-Mount Transmitter Use the (2) included screws to mount the transmitter to a wall securely near an outlet.
-
Page 10: Description Of Receiver Parts
DESCRIPTION OF RECEIVER PARTS Collar Strap Contact Points Battery Charging Receptacle & Rubber Plug LED Indicator Light Stimulation Selection Dial E-FENCE 3500 Receiver... - Page 11 Stimulation Selection Dial The stimulation level is adjustable from each individual dog’s receiver so that Stimulation Selection Dial it is easy to accomodate to each dog’s different personality and temperament. The stimulation levels range from level 1 to level 8 (1 being the lowest and 8 being the highest).
-
Page 12: Receiver Fitting
If the receiver is too loose, the contact will not be consistent and cause the corrections to be inconsistent. Dogtra uses medical grade stainless steel contact points and anti-microbial plastic to protect the dog’s skin. -
Page 13: Adaptor
ADAPTOR Transmitter Receiver Adaptor Adaptor (5Volt 1A) (24Volt 500mA) The battery charger is designed for a 120-volt wall outlet. -
Page 14: Charging The Receiver
Dogtra e-collars. This will prevent any damage that can be incurred from attempting to use a different charger. NOTE 2: The unit has a partial charge when it leaves the Dogtra facility. Upon receipt of the system, be sure to give it a full 2-hour initial charge before the first use away from any flammable substances. -
Page 15: Changing The Contact Point Length
CHANGING THE CONTACT POINT LENGTH The Dogtra E-FENCE 3500 comes equipped with standard 5/8” contact points that can be extended to 3/4” contact points, for use with dogs with longer coats. To increase the contact point length from 5/8” to 3/4”, follow the steps below. -
Page 16: Testing The System Prior To Installation
TESTING YOUR SYSTEM PRIOR TO INSTALLATION 1. To ensure that your E-FENCE 3500 system is working properly, connect the power adaptor into the transmitter power jack and then plug the power adaptor into a household outlet. Switch the stimulation knob to Pager/ Stimulation or Pager Only. -
Page 17: Installation
INSTALLATION Fence Wire The e-fence boundary wire must make a continuous loop around your property for the system to operate. The signal is delivered from the terminal of the transmitter, through the fence wire, back to the other terminal on the transmitter. When this is accomplished, the wire continuity light will emit a constant red indicator. - Page 18 Common Boundary Designs *The diagrams below are indicated for a rectangular layout. House House Front Boundary Only Fence Front Yard Only House House Front or Back Access Basic Loop with Garden twisted wire neutral House House zone passage Front Boundary with Existing Fence Double Loop with Passage...
- Page 19 * Please note the diagrams are not drawn to scale. The E-FENCE 3500 system includes 500 feet of boundary wire and 50 training flags. Additional flags and wiring can be purchased through the Dogtra Company. The estimated requirements are as follows: Fence Wire(500ft./spool)
- Page 20 Additional Parts 20ga Underground Fence Wire Boundary Training Flags (500 feet) (50 each bundle) Actual flag/wire requirements may vary depending on the layout you’ve chosen. You will want to keep a signal field (area where the dog will receive stimulation) at least 6-8 feet on each side of the wire.
- Page 21 Creating a Neutral Zone in the Boundary You must create a neutral zone from the fence transmitter to the beginning of the fence so the signals do not cross over to any existing utility wires. Start by twisting the two pieces of fence wire so they are braided from the beginning of the neutral zone area to the end.
- Page 22 IMPORTANT Bury the fence wire after you have tested the system and are sure it is working properly. Do not nick or scrape the fence wire during installation as it may result in an intermittent signal or no signal. Make gradual turns at the corners with a radius of at least 3 feet.
-
Page 23: Wire Splicing
WIRE SPLICING The wire connection must be waterproof. Do not use electrical tape, or soldered/twisted wire nuts in this type of connection as it will cause an intermittent signal or disarm the system. The waterproof splices included in the E-FENCE 3500 system are designed to provide a sealed connection between the wires. - Page 24 Connecting the Fence Wire to the Transmitter Splice the two ends of the twisted wire to each of the two ends of the fence wire. Drill a hole through the exterior wall or window/door sill or run the fence wire through an existing utility line hole.
-
Page 25: Optional Accessories
OPTIONAL ACCESSORIES The following items may be purchased separately. To purchase accessories, please visit Dogtra's online store at www.dogtra.com or call customer service at (888) 811-9111. Transmitter Power Receiver Charger Adaptor (24Volt 500mA) (5Volt 1A) · European Adaptor for 220-volt outlets... - Page 26 Connecting a Lightning Surge Protector Transmitter Adaptor Transmitter Loop Transmitter Fence wires Transmitter Wires Plug the lightning protector into a grounded (3-wire) 120V AC outlet within five feet of where you want to locate the transmitter. Cut the e-fence wires near the protector and strip all four ends back ¼...
-
Page 27: Troubleshooting Guide
TROUBLESHOOTING GUIDE 1. My dog is not reacting to the receiver. – Make sure the receiver and transmitter are turned on. – Make sure the collar strap is tight enough so both contact points are touching the dog’s skin. – The contact points may be too short for the dog. To place an order for longer contact points that are more appropriate for your dog, please call (888) 811- 9111. - Page 28 Finding a wire break using an Underground Cable Wire Locator* E-FENCE boundary wire 1. Go to the E-FENCE 3500 wall-mounted transmitter and disconnect the two boundary wire leads from the red connector tabs. 2. Get the Underground Cable Wire Locator transmitter: - Connect the red alligator clip to the end of one of the E-FENCE 3500 boundary wires.
-
Page 29: General Maintenance Tips
GENERAL MAINTENANCE TIPS Your system requires very little maintenance. The receiver for the E-FENCE 3500 system is fully waterproof. To remove dirt, simply wipe with soap and water. The wall transmitter is not waterproof and must be protected from the elements in a shed, garage or carport. -
Page 30: Warranty And Repair Information
No dealer of Dogtra products, nor any employee or agent of Dogtra, is authorized to make any additions, changes, or extensions to the Warranty. Dogtra, at its sole discretion and at any time, reserves the right to modify the Warranty. - Page 31 (see below for contact information). Upon approval of your warranty work, Dogtra will repair or replace (at Dogtra’s election) your product without charge for labor or parts. You are responsible for shipping, including cost, of your product to Dogtra for warranty service. Dogtra will handle shipping, including cost, of the repaired or replaced product back to customers in the USA.
- Page 32 The device has been approved for use in EU countries and is therefore provided with the CE All necessary documentation is available on the website: www.electric-collars.com mark. Changes to technical parameters, properties and printing errors reserved. Service center and distribution Reedog, sro Sedmidomky 459/8 101 00 Prague 10...
Need help?
Do you have a question about the EF-3500 and is the answer not in the manual?
Questions and answers