Advertisement
5494 Remote Controller
plus Twinax Expansion, Token Ring, and Ethernet Add-In Cards
CUSTOMER
SUPPORT
INFORMATION
Installation Guide
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
T e s t
T e s t
P o w e r
S C T S
X D R T
T X D R
N o rm a
l
5 4 9 4
R e m o te
ll e r
C o n tr o
F
O N /O F
JULY 1998
PC394A-R3
PC394AE-R3
PC394C
PC395C
PC396C
PC397C
D is k
W S
E rr o r
C o m
A c ti v e
R e a d y
L in e
R X C
T X C
T R C D
D S R D
Advertisement
Table of Contents
Related Manuals for Black Box 5494 Remote Controller
Summary of Contents for Black Box 5494 Remote Controller
- Page 1 Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 SUPPORT Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 INFORMATION Web site: www.blackbox.com • E-mail: info@blackbox.com...
-
Page 2: Federal Communications Commission
INSTALLATION GUIDE FEDERAL COMMUNICATIONS COMMISSION INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. - Page 3 5494 REMOTE CONTROLLER INSTRUCCIONES DE SEGURIDAD (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
-
Page 4: Trademarks Used In This Manual
INSTALLATION GUIDE TRADEMARKS USED IN THIS MANUAL is a registered trademark of International Business Machines Corporation. ® Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. -
Page 5: Power Switch
5494 REMOTE CONTROLLER Unpacking the Box Place the packing box containing your Remote Controller in an area with ample room for unpacking. Open the box and remove the contents. Use the checklist below to make sure you have all the items in the box. Keep the box and packing materials in case you need to move or ship the equipment later. -
Page 6: Installing Additional Cards
INSTALLATION GUIDE MPIC Card Optional Ethernet Card Expansion Slots for Additional Cards Lid Release Screw Twinax Card Serial/Ratings Label Lid Release Clip Status LEDs AC Power Connector Figure 2. Back of the Controller. Choose a Site Place the Remote Controller on a desk or table top where you will be using it. Make sure the Remote Controller has at least six inches of clearance (air space) on the top, sides, and back for cooling. - Page 7 5494 REMOTE CONTROLLER To install a card in the Remote Controller: 1. Turn off the power to the Remote Controller. 2. Remove the single screw at the top center of the back cover. 3. Remove the cover. 4. Locate the next available slot in the Remote Controller (if installing additional twinax cards), and remove the slot cover.
- Page 8 INSTALLATION GUIDE Set the DIP Switches You must set the DIP switches on each additional twinax card you install to correspond to the slot number in which the card is installed. 1. Read the label on the back of the Remote Controller, above the slots, to determine the slot number. 2.
- Page 9 5494 REMOTE CONTROLLER Setting Up for Local Attachment The Remote Controller is shipped from the factory set for remote communications. You can also attach the controller locally. If you use your Remote Controller for local communications, you must use one of the communications cables listed below.
- Page 10 INSTALLATION GUIDE Attach the Devices Take the following steps to attach twinax devices to your Remote Controller. 1. Attach a twinax cable to each twinax device you will be connecting to the Remote Controller. 2. Make a note of the cable and cable address on the installation checklist on the next page. 3.
-
Page 11: Installation Checklist
5494 REMOTE CONTROLLER Installation Checklist ___Unpack and choose a site for the Remote Controller. ___Install twinax cards. ___Install Ethernet/Token Ring card (if applicable). ___Set switches on twinax cards for proper slot number. ___Set up for local attachment (if applicable). ___Connect all cables. - Page 12 INSTALLATION GUIDE Device Default Printer Device Default Printer Card #1 Cable Address Description (displays only) Card #2 Cable Address Description (displays only) Display Display Stations: Stations: Printers: Printers: Other: Other: Device Default Printer Device Default Printer Card #3 Cable Address Description (displays only) Card #4 Cable Address...
- Page 13 © Copyright 1998. Black Box Corporation. All rights reserved. 1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746...
Need help?
Do you have a question about the 5494 Remote Controller and is the answer not in the manual?
Questions and answers