Omron VARISPEED L7 Manual page 138

Special Sequence Functions: S3
Name
Param-
eter
Num-
Display
ber
Short-floor Enables or disables the short floor
function selec- operation function
S3-01
tion 0: disabled
1: enabled (Standard)
Short floor sel
2: enabled (Advanced)
Inspection
deceleration
Sets the deceleration time for the
S3-03
time
inspection run.
Dec ramp inspec
Nominal/Level-
Sets the speed level for Nominal/
ing speed detec-
Leveling speed detection when
S3-04
tion level
multispeed inputs are used.
(d1-18=0/3)
Vn/Vl level sel
Nominal speed
Sets the nominal speed value
for short floor
S3-05 which is used for the short floor
calculation
calculation.
Vn@ Short floor
Light load Enables or disables the Light load
search for res- search function for rescue opera-
cue operation tion.
S3-06
0: disabled
LightLoad
1: enabled
Search
2: enabled (for motor 1 only)
Light load
search time
Sets the light load search time for
S3-07
the rescue operation.
LightLd Srch-
Time
Output phase
Sets the output phase order.
order
S3-08
0: Output phase order is U-V-W
1: Output phase order is U-W-V
Exchg Phase Sel
Frequency refer- Enables or disables the frequency
ence loss detec- reference loss detection when d1-
S3-09 tion 18 = 1 and H1-
0: Disabled
FRL selection
1: Enabled
Light load
search fre-
Sets the light load speed for the
quency
S3-10
rescue operation.
LightLd Srch-
Freq
Rescue opera-
tion torque limit Sets the torque limit for the rescue
S3-11
operation.
Rescue OP
TLM
Base Block Sets the behaviour of the inverter
restart selection if a Base Block command is set
during run.
0: Disabled
The Run command must be
S3-12
cycled to restart.
BB Restart
1: Enable
The inverter restarts when the
Base Block signal is released
and the Run signal is still active.
Traction sheave
Sets the diameter of the traction
diameter
S3-13
sheave.
Sheave diameter
Setting Factory
Description
Range
0 or 1
0.0 to
2.0
0.0 to
120.0
0.0 to
120.0
0 or 2
0.0 to
5.0
0 or 1
0 or 1
K83.
0.00 to
3.00 Hz
20.00
0 to 300
0 or 1
100 to
2000
Control Methods
Change
during
Open
Setting Opera-
V/f Loop
tion
Vector
0 No A A
0.0sec No A A
0.0Hz No A A
0.0Hz No A A
0 No A A
1.0 sec No A A
0 No A A
1 No A A
No A A
100 % No - A
0 No A A
400
No A A
mm
MEMO-
Closed
Closed
BUS Page
Loop
Loop
Register
Vector
Vector
(PM)
A A 6BDH 6-17
A A 6BFH 6-11
A A 6C0H 6-6
A A 6C1H 6-16
A A 6C2H 6-80
A A 6C3H 6-80
A A 6C4H 6-63
A A 6C5H 6-8
A A 6C6H 6-77
A A 6C7H 6-77
A A 6C8H 6-50
A A 6C9H 6-65
5
51
5-