Baroness GM2810A Owner's Operating Manual

Baroness GM2810A Owner's Operating Manual

5-unit rotary mower
Hide thumbs Also See for GM2810A:
Table of Contents

Advertisement

Quick Links

5-Unit Rotary Mower
Owner's Operating Manual
Serial No.
GM2810A:11374-
"Required reading"
Read this manual before using the machine.
Original Instructions Ver.1.7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GM2810A and is the answer not in the manual?

Questions and answers

Summary of Contents for Baroness GM2810A

  • Page 1 5-Unit Rotary Mower Owner's Operating Manual Serial No. GM2810A:11374- "Required reading" Read this manual before using the machine. Original Instructions Ver.1.7...
  • Page 2 GM2810A Regulations California Proposition 65 EU Regulations (For California, USA) (For EU) This product complies with all relevant EU Regulations. WARNING: For more information, please refer to the Operating, servicing and maintaining Declaration of Conformity attached. a passenger vehicle or off-road EU Emission Control (StageⅤ)
  • Page 3 GM2810A Greeting Thank you for purchasing the Baroness product. QR Code This manual describes the proper handling, adjustment, and inspection of your product. A QR code label is affixed on the machine. We hope you will use the product safely, and take advantage of its best performance.
  • Page 4 The operator is responsible for operating the product properly and safely. Maintenance service for this machine should be performed by a mechanic with expertise. If you have any questions concerning maintenance or genuine parts, please contact a Baroness dealer or Kyoeisha.
  • Page 5 When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies. Prior to use, carefully read the following manuals to thoroughly understand the contents for safe and correct operation.
  • Page 6 GM2810A Introduction...
  • Page 7: Table Of Contents

    GM2810A Contents Safety .............. Page 1-1 Maintenance ........... Page 6-1 Safe Operating Practices .......Page 1-2 Precautions for Maintenance ......Page 6-2 Jacking Up The Machine ....... Page 6-2 Disposal ............Page 2-1 Greasing ............Page 6-3 Recycle and Waste Disposal ......Page 2-2 Lubrication .............
  • Page 8 GM2810A Contents...
  • Page 9: Safety

    GM2810A Safety Safe Operating Practices ...... Page 1-2 Training ..........Page 1-2 Preparation ..........Page 1-2 Operation ..........Page 1-3 Maintenance .......... Page 1-4 Storage ..........Page 1-5 Page 1-1...
  • Page 10: Safe Operating Practices

    GM2810A Safety Failure to adequately follow these safety Never allow children or people unfamiliar precautions may cause an accident resulting in with these instructions to use or service the injury or death. machine. Local regulations may restrict the age of the Danger operator.
  • Page 11: Operation

    GM2810A Safety Add fuel before starting the engine. Never operate the machine with damaged Never remove the cap of the fuel tank or guards, shields, or without safety protective add fuel while the engine is running or devices in place.
  • Page 12: Maintenance

    GM2810A Safety Do the following before leaving the Maintenance operator's position. Never allow untrained personnel to service Stop on level ground. machine. Disengage the all drives. Implement the following work before Set the parking brake. adjusting, cleaning or repairing. Stop the engine.
  • Page 13: Storage

    GM2810A Safety Check whether line connectors in the Swallowing engine coolant can cause injury hydraulic system are properly tightened. or death; keep out of reach from children and Before applying hydraulic pressure, check pets. the connections of the hydraulic pressure lines and the condition of the hoses.
  • Page 14 GM2810A Safety Page 1-6 Safe Operating Practices...
  • Page 15: Disposal

    GM2810A Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1...
  • Page 16: Recycle And Waste Disposal

    GM2810A Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations.
  • Page 17: Product Overview

    GM2810A Product Overview Specifications ........Page 3-2 Specifications .........Page 3-2 Sound Pressure Level ......Page 3-3 Sound Power Level ....... Page 3-3 Vibration Level ........Page 3-3 Carbon Dioxide (CO2) Emissions ..Page 3-3 Names of Each Section ......Page 3-4 Regulation Decals ........Page 3-5...
  • Page 18: Specifications

    GM2810A Product Overview Specifications Specifications Model GM2810A Name 5-Unit Rotary Mower Total length 370 cm 145.67 in During 300 cm 118.11 in operation Total width During Dimensions 230 cm 90.55 in transport Roof 230 cm 90.55 in Total height Steering 165 cm 64.96 in...
  • Page 19: Sound Pressure Level

    GM2810A Product Overview Battery 105D31R Engine plug The factory default maximum engine rpm is 2,600 rpm. Sound Pressure Level Sound Pressure Level This machine was confirmed to have a continuous A-weighted sound pressure level of 90dB by measuring identical machines in accordance with the procedure specified in ISO 5395-1:2013.
  • Page 20: Names Of Each Section

    GM2810A Product Overview Names of Each Section Seat Steering handle Tilt lever Diff-lock switch Parking brake lever Brake pedal Forward pedal Reverse pedal Mower deck up/down lever Throttle knob Knife rotation switch 2WD/4WD selector switch Fuel tank Hydraulic tank 11,12...
  • Page 21: Regulation Decals

    GM2810A Product Overview Regulation Decals Specification Decal (For EU) Positions of Regulation Decals The Specification decal indicates the model and weight, etc. B,C,D I,J,K 8804A96B Positions of Regulation Decals_001 450597AD Serial number plate Specification Decal_001 Specification decal CE Mark CE mark...
  • Page 22 GM2810A Product Overview Noise Emission Decal ROPS Compliance Decal (For EU) The ROPS compliance decal indicates the The noise emission decal indicates the sound manufacturer, model, etc., in accordance with power level determined by measuring International Standard ISO 21299:2009. identical machines in accordance with the procedure specified in the regulations of EU or UK.
  • Page 23 GM2810A Product Overview Recycle Decal California Proposition 65 Decal (Riding Type) Recycle Decal illustrates Recycle Mark in (For the State of California, USA) accordance with local regulation. California Proposition 65 decal describes the (For EU) warning messages as required by California Proposition 65.
  • Page 24: Safety Signs And Instruction Signs

    A0D6B73C Positions of Safety Signs and Instruction Signs_002 Part numbers for decals that need to be replaced are listed in the parts catalog. Order them from a Baroness dealer or Kyoeisha. Positions of Safety Signs and Instruction Signs 6iul4h-183...
  • Page 25 GM2810A Product Overview 6iul4h-055 6iul4h-184 Positions of Safety Signs and Instruction Signs_006 Positions of Safety Signs and Instruction Signs_010 Operation decal Engine start/stop decal Caution to mutilation decal Caution for high temperatures decal Caution to injury decal Caution to rotating object decal...
  • Page 26: Description Of Safety Decals And Instruction Decals

    Turn the key to the "ON (GLOW)" Warning position, and then wait for the logo "BARONESS" to be turned off. Apply the parking brake, stop the engine, Turn the key to the "START" position. remove the ignition key, and then leave the machine.
  • Page 27 GM2810A Product Overview Caution to Mutilation Decal Caution to Injury Decal K4205001600 K4205001580 DECAL, CAUTION TO MUTILATION Decal, caution to injure Warning Caution May cut your hand or leg - Stop the cutter May pinch - There is a risk of being pinched.
  • Page 28 GM2810A Product Overview Hydraulic Oil Icon Fire Prohibited Decal K4209000980 K4205001940 Hydraulic oil icon Decal, fire prohibited Read the Owner's Operating Manual. Warning Keep away from fire. i77xz6-001 Hydraulic Oil Icon_001 Diesel Fuel Icon r653fo-001 K4209001000 Fire Prohibited Decal_001 Diesel fuel icon Caution for Mower Lock Decal Use diesel fuel.
  • Page 29 GM2810A Product Overview Caution for Spouting Coolant Decal Caution to Flying Object Decal K4205001970 K4205001650 Decal, caution for spouting coolant Decal, caution to flying object Caution Caution Caution for spouting coolant - Do not open Caution to flying object - Be sure that people while hot.
  • Page 30 GM2810A Product Overview Caution Exhaust Gas Decal Maintenance Decal K4205001950 K4209001940 Decal, caution exhaust gas Maintenance decal The maintenance decal indicates the Warning necessary inspection and maintenance items for this machine. Caution for exhaust gas kvwx52-001 Caution Exhaust Gas Decal_001...
  • Page 31 GM2810A Product Overview 2WD/4WD Selector Important Decal Indicating Diesel Fuel Decal K4205002330 K4209001530 DECAL, IMPORTANT 2WD/4WD SELECTOR DECAL, INDICATING DIESEL FUEL Indicating diesel fuel decal describes the type Important of fuel to be used. Use Ultra Low Sulfur Diesel Fuel (sulfur-free Be sure to operate the 2WD/4WD selector diesel).
  • Page 32: Operation Decals

    GM2810A Product Overview Operation Decals Key switch decal Knife rotation mark Positions of Operation Decals Traction assist mark 2WD/4WD selector mark DPF regeneration mark (EN) Mower deck up/down mark Light switch mark Engine rotation mark Tilt Steering decal Parking brake decal...
  • Page 33: Description Of Operation Decals

    GM2810A Product Overview Description of Operation Decals Traction Assist Mark Key Switch Decal Traction assist mark It illustrates Activate/ Deactivate of the Decal, key switch traction assist. This indicates the key switch positions. O F F krtths-002 v2e27i-071 Traction Assist Mark_001...
  • Page 34 GM2810A Product Overview DPF Regeneration Mark (EN) Light Switch Mark Note: DPF regeneration mark (EN) Depending on the specifications, this function This indicates the changeover of DPF may not be available. regeneration. Light switch mark It illustrates ON/OFF of the light.
  • Page 35 GM2810A Product Overview Differential Lock Decal Parking Brake Decal K4203001420 K4203001340 Decal, differential lock Parking brake decal This indicates the positions for engaging or This shows how to lock and release the releasing the differential lock. parking brake. 3ujqne-001 kgtxi7-002...
  • Page 36 GM2810A Product Overview BACKWARD Decal K4203001440 Decal, BACKWARD This indicates backward travel. BACKWARD kqca3e-002 BACKWARD Decal_001 BRAKE Decal K4203001450 Decal, BRAKE This indicates brake. BRAKE 7elqr2-001 BRAKE Decal_001 Page 3-20 Operation Decals...
  • Page 37: Description Of Functions

    GM2810A Description of Functions Proximity Sensors ......... Page 4-2 DPF ............Page 4-40 Relays ............. Page 4-2 Knife Rotation Switch ......Page 4-3 2WD/4WD Selector Switch ....Page 4-3 DPF Auto Regeneration Inhibit Switch ............. Page 4-4 DPF Parked Regeneration Switch ..Page 4-5 Light Switch ...........
  • Page 38: Proximity Sensors

    GM2810A Description of Functions Proximity Sensors There are two proximity sensors on mower arm fulcrums #4 and #5. These sensors detect the raised or lowered positions of mower decks #4 and #5. The information is related to controlling rotation and stop of the rotary knives.
  • Page 39: Knife Rotation Switch

    GM2810A Description of Functions Knife Rotation Switch Caution When traveling, be sure to stop the rotation of Caution the rotary knives and raise the mower decks. Set the knife rotation switch to the "Rotation" position immediately before starting cutting Important work.
  • Page 40: Dpf Auto Regeneration Inhibit Switch

    GM2810A Description of Functions In "Auto regeneration inhibit mode" PM DPF Auto Regeneration Inhibit Switch accumulates in the DPF and PM accumulation level increases. Caution Unless the operator implements regeneration on his own will, regeneration is not performed. Normally, set the DPF auto regeneration inhibit switch to "Auto regeneration mode".
  • Page 41: Dpf Parked Regeneration Switch

    GM2810A Description of Functions DPF Parked Regeneration Switch Light Switch Note: Danger Depending on the specifications, this function may not be available. Do not perform DPF regeneration in a location where fires may occur since it will become Caution extremely hot around the exhaust outlet during DPF regeneration.
  • Page 42: Traction Assist Switch

    GM2810A Description of Functions Traction Assist Switch The traction assist switch is located in the operation panel. This switch is effective to increase climbing ability when this machine is in cutting operation (4WD). ・ The cylinders are pressurized even with the switch set to the "OFF"...
  • Page 43: Throttle Knob

    GM2810A Description of Functions Mower deck up/down lever Raise Neutral Lower Throttle Knob The throttle knob is located to the right of the driver's seat and enables you to adjust the engine rpm. Move the throttle knob toward the "High speed"...
  • Page 44: Brake Pedal

    GM2810A Description of Functions Change of Braking Method Brake Pedal Follow the procedure below to change the Warning braking method from linked to independent. Swing up the pedal link bar, and then pull it Link the brake pedals, except when operating the machine.
  • Page 45: Parking Brake Lever

    GM2810A Description of Functions Parking Brake Lever Important When you restart the engine after the safety Caution device stops the engine, be sure to return the ignition key to the "OFF" position first, and Never park the machine on a slope.
  • Page 46: Engine Warning Lamp

    GM2810A Description of Functions Hydraulic Oil Level Warning Buzzer If the oil level in the hydraulic tank declines from the specified level by approximately 2.0 (2.0 L), a buzzer will sound. (continuous tone) When the buzzer sounds, stop the engine immediately, and then inspect the machine and perform any necessary maintenance.
  • Page 47: Monitor (Pv380)

    GM2810A Description of Functions Monitor (PV380) Fault detected Recovery The monitor displays various information about Blinking the machine, such as the operating status and Lighting fault conditions. The information of desired items can be Monitor LED confirmed according to operation of the keys.
  • Page 48: Opening Screen

    GM2810A Description of Functions Three seconds after activating the monitor, Opening Screen GAUGE screen appears. Set the ignition key to the "ON" position. One or two seconds after activating the monitor, LOGO screen appears. 753B785E Opening Screen_001 ENGINE SPEED HOUR METER...
  • Page 49: Gauge Screen

    GM2810A Description of Functions Gauge Screen Gauge screen appears after the monitor activation. It shows the status of the engine and the vehicle. Move to another screen or page with pressing the arbitrary button. ・ "Button 5": Move to another page of GAUGE screen.
  • Page 50 GM2810A Description of Functions The first page (displayed when the monitor The third page activated) DPF ACTIVE REGEN DOC TEMP INACTIVE ENGINE SPEED HOUR METER DPF INTAKE TEMP DPF OUTLET TEMP COOLANT TEMP FUEL LEVEL 8C29AC98 83ABD857 Gauge Screen_004 Gauge Screen_002 The second page %...
  • Page 51: Menu Screen

    GM2810A Description of Functions The fourth page Menu Screen Note: If "Button 5" is pressed on the fourth page, MENU screen displays a variety of information the first page appears in the screen. like the engine and vehicle status, etc. and the setting menu.
  • Page 52 GM2810A Description of Functions Press the button 3 to move to MENU User Settings screen and save the setting. If you turn the ignition key to the "OFF" Set an arbitrary item with pressing the button position before moving to MENU screen, of the item.
  • Page 53 GM2810A Description of Functions Press the button 3 to move to MENU Italian ・ screen and save the setting. Portuguese ・ If you turn the ignition key to the "OFF" Dutch ・ position before moving to MENU screen, Press the button 3 to move to MENU the setting will not be saved.
  • Page 54 GM2810A Description of Functions Press the button 3 to move to MENU Units ■ screen and save the setting. If you turn the ignition key to the "OFF" With "UNITS", the units of parameter values position before moving to MENU screen, can be set.
  • Page 55 GM2810A Description of Functions Service Reminders "SERVICE REMINDERS" functions to notify the operator of the appropriate timing of service for the following items. Engine oil: Notification of timely ・ replacement of the engine oil Engine oil filter: Notification of timely ・...
  • Page 56 GM2810A Description of Functions The hours calculated based on the expiry of Service Reminders Reset ■ the setup service interval hours appears as a positive or negative number on the right side With "SERVICE REMINDERS", the of the items in "SERVICE REMINDERS".
  • Page 57 GM2810A Description of Functions Note: The message "Reset complete" appears If the button 4 is pressed while the engine when the setting saved. running, the following message appears. Note: Once the displayed number reset, it appears as calculated based on the "periodical service interval hours".
  • Page 58 GM2810A Description of Functions Press the button 3 to move to MENU Press the button 5 to move to SERVICE screen. REMINDERS SETTING screen. SERVICE REMINDERS SERVICE REMINDERS ENGINE OIL ENGINE OIL ENGINE OIL FILTER ENGINE OIL FILTER HYDRAULIC OIL...
  • Page 59 GM2810A Description of Functions Press the button 5 to determine the setup hours. 50.0 400.0 450.0 400.0 50.0 400.0 450.0 400.0 SERVICE REMINDERS SETTING ENGINE OIL HOUR METER INTERVAL SERVICE REMINDERS 50.0 400.0 SETTING Locked while the Engine is running INSPECTION TIME REMAINING ENGINE OIL 450.0...
  • Page 60 GM2810A Description of Functions The interval hours after configuration Press the button 3 to move to MENU saved appear in SERVICE REMINDERS screen. SETTING screen. Press the button 3 to move to SERVICE REMINDERS screen. 50.0 400.0 450.0 400.0 SERVICE REMINDERS...
  • Page 61 GM2810A Description of Functions Press the button 4 to delete the settings. Service Reminders Setting Deletion ■ With "SERVICE REMINDERS", the setup hours can be deleted. Important 50.0 400.0 The setting of the service reminders can not - - - be changed while the engine is running.
  • Page 62 GM2810A Description of Functions Note: The message "Deletion complete" If the button 4 is pressed while the engine appears when the setting saved. running, the following message appears. 50.0 400.0 50.0 400.0 - - - 450.0 400.0 SERVICE REMINDERS SETTING...
  • Page 63 GM2810A Description of Functions Press the button 3 to move to SERVICE Press the button 3 to move to MENU REMINDERS screen. screen. 50.0 - - - SERVICE REMINDERS SERVICE REMINDERS SETTING ENGINE OIL ENGINE OIL ENGINE OIL FILTER HOUR METER...
  • Page 64 GM2810A Description of Functions The monitor receives the stored fault codes Stored Fault Codes while "RECEIVING" message appears. With "STORED FAULT CODES", the past fault codes can be checked. Once "STORED FAULT CODES" is SPN: 0 FMI: 0 selected, the monitor automatically requests the engine ECU to send the stored fault codes while "REQUESTING"...
  • Page 65 GM2810A Description of Functions The stored fault codes appear after the In case of plural stored fault code reception completed. The arrows of "↓" and "↑" appear in the Note: bottom of the monitor display. Press "Button 5" if you would like to receive Press "Button 1"...
  • Page 66 GM2810A Description of Functions In case of no stored fault code Installed "CONFIGURATION TITLE" "NO STORED FAULT CODES" appears. "Button 3": Move to the MENU screen. ・ SPN: 0 FMI: 0 ******* ***** STORED FAULT CODES VERSION INFORMATION SPN: 0 FMI: 0...
  • Page 67 GM2810A Description of Functions Refuel icon Descriptions of Displayed Icons The icon appears and blinks when the remaining fuel decreases to less than 10 The following icons appear in the GAUGE screen. Cleaning index icon The icon appears when the cleaning index is 50 %, 75 % or 100 %.
  • Page 68 GM2810A Description of Functions Slow blinking (Repeat of lighting up and DPF regeneration icon ・ down every 2 sec): The engine may be The DPF regeneration icon appears with stopped in the end due to decreasing DPF regeneration request or during DPF power output, etc.
  • Page 69 GM2810A Description of Functions Descriptions of Pop-up Messages These pop-up messages appear in the monitor display. SPN: 110 FMI: 3 P0118 High ・ FAULT CODES SERVICE REMINDERS ・ DPF CLEANING ALARM ・ Fault Codes Important When the fault code (DTC) appears in the monitor display, contact your dealer.
  • Page 70 GM2810A Description of Functions SPN: 110 FMI: 3 P0118 High ・  再生禁止 FAULT CODES FAULT CODES SPN: 110 FMI: 3 P0118 Coolant temperature sensor : CAN BUS FAILURE(ENGINE ECU NO High COMMUNICATION)    ・  Regeneration inhibited 3BDCD26B 42059C59 Fault Codes_002 Fault Codes_003...
  • Page 71 GM2810A Description of Functions Follow the instruction from "Recovery from Important error" of "List of Fault Codes." When "SERVICE REMINDERS" and "FAULT Important CODES" or "DPF CLEANING ALARM" are When "FAULT CODES" and "SERVICE advised at the same time, "SERVICE REMINDERS"...
  • Page 72 GM2810A Description of Functions When five items should be advised for The second page ・ example, they appears in two pages. In that case, the arrows "←" and "→" appear in the bottom of the monitor display. You can move to another page with pressing "Button 1"...
  • Page 73 GM2810A Description of Functions Move to GAUGE screen with pressing When the prescribed time of Ash Timer has "Button 3" when the message displayed. elapsed, the pop-up message appears in The service icon appears in GAUGE the monitor display and the yellow LED screen.
  • Page 74 GM2810A Description of Functions When the prescribed time of Ash Timer Cleaning index 75 % ・ has not elapsed yet and the cleaning index is 50 % or more Cleaning index 50 % ・ 75  50  DPF CLEANING ALARM CLEANING INDEX 75 ...
  • Page 75 GM2810A Description of Functions Cleaning index 100 % Move to GAUGE screen with pressing ・ "Button 3" when the message displayed. The cleaning index icon appears in GAUGE screen. 100  DPF CLEANING ALARM CLEANING INDEX 100  CLEANING INDEX is now 100%...
  • Page 76: Engine

    GM2810A Description of Functions Engine Precautions for DPF Handling Emission Control Compliant Engine Danger Important Since it will become hot around the exhaust outlet during DPF regeneration, do not When performing maintenance or repairs on perform DPF regeneration in a location where this engine, only use dedicated replacement fires may occur.
  • Page 77 GM2810A Description of Functions The traveling pedal is in the neutral ・ DPF Regeneration and Replacement position. The DPF is a purifying filter that collects PM The engine rotation speed is minimum ・ (soot) from exhaust gas. or idling speed.
  • Page 78 GM2810A Description of Functions PM Accumulation Level ■ The following table shows the regeneration method and the machine status in each PM accumulation level. PM accumulation DPF regeneration Displayed fault code Monitor LED Engine output limit level method Level 0...
  • Page 79 GM2810A Description of Functions When the conditions for auto The traveling pedal is in neutral. ・ regeneration are met, DPF auto The engine rotation speed is minimum or ・ regeneration starts and DPF idling speed. regeneration icon changes from blinking ・...
  • Page 80 GM2810A Description of Functions In "Auto regeneration inhibit mode" or "Excessive PM3" appears in the monitor ・ when DPF auto regeneration inhibit display. icon appears: SPN: 3701 FMI:15 P3006 PM B046977A DPF Parked Regeneration_002 DPF regeneration icon FAULT CODES DPF auto regeneration inhibit icon...
  • Page 81 GM2810A Description of Functions "Excessive PM4" appears in the monitor DPF Manual Regeneration ■ display. Important You cannot perform DPF manual SPN: 3701 FMI:16 regeneration. P3007 PM Contact your dealer for DPF manual regeneration. The expert performs "DPF Manual regeneration" with the fault diagnostic tool...
  • Page 82 GM2810A Description of Functions Replacement of DPF ■ LED (red) Park this machine in a safe location Note: immediately. This machine features a function of "DPF Cleaning Alarm". Apply the parking brake. When PM and ash accumulate excessively Stop the engine.
  • Page 83 GM2810A Description of Functions Relationship between PM Accumulation Level and DPF Regeneration Important In "Auto regeneration inhibit mode", any DPF regeneration of "Auto", "Parked" and "Manual" is prohibited. Cancel "Auto regeneration inhibit mode" to perform DPF regeneration. In "Auto regeneration mode" or when DPF auto regeneration inhibit icon disappears:...
  • Page 84 GM2810A Description of Functions Page 4-48 Engine...
  • Page 85: Handling Instructions

    GM2810A Handling Instructions Operations Before Service ....Page 5-2 Leaving the machine ......Page 5-22 Move ............Page 5-22 Opening and Closing of Hood ....Page 5-2 Traveling Procedure ......Page 5-22 Opening and Closing of Underseat Cover ............Page 5-3 Cutting Work ........Page 5-23 Inspection and Cleaning .......
  • Page 86: Operations Before Service

    GM2810A Handling Instructions Operations Before Service Rubber catch Catch clip The following sections describe the preparatory works required before performing the services Bolt including inspection, adjustment, cleaning. maintenance and repair. Lift up the hood. Opening and Closing of Hood Hook the hood stay on the receiver on the back side of the hood.
  • Page 87: Opening And Closing Of Underseat Cover

    GM2810A Handling Instructions Opening and Closing of Underseat Inspection and Cleaning Cover Inspect and clean the machine with the goals of the followings. Caution Accident prevention ・ Be careful not to pinch your fingers when you ・ Failure prevention open or close the underseat cover.
  • Page 88: Radiator Cover

    GM2810A Handling Instructions Make sure that there are no cracks or tears Radiator cover between the sail and flat part of the rotary knife. Carefully clean the front and back of the radiator cover with water or compressed air. Radiator...
  • Page 89: Coolant

    GM2810A Handling Instructions Oil cooler Caution Rubber catch Supply coolant after the engine has well Radiator cooled down. Carefully clean the front and back of the radiator with water or compressed air. Caution Coolant The radiator cap is pressurized. If you remove the radiator cap while the...
  • Page 90: Oil Cooler

    GM2810A Handling Instructions Open the reserve tank cap, and then Unlock the rubber catches on the left and supply clean water up to the "FULL" right of the oil cooler, and then tilt the oil mark. cooler. C30D7599 ouuoov-014 Coolant Supply_002...
  • Page 91 GM2810A Handling Instructions Tighten the tank cap securely. Hydraulic Oil Supply Important Do not mix different types of oil. Important Use Shell Tellus S2M46(or equivalent)as hydraulic oil. In the case of using an equivalent, consult Characteristics of Hydraulic Oil and use...
  • Page 92: Hydraulic Hoses

    GM2810A Handling Instructions Check underneath the machine for oil leakage. Install the left tank cover. Hydraulic Hoses Inspection of Hydraulic Hoses and Pipes Warning When checking the hydraulic circuit for pinhole leaks or oil leakage from nozzles, do pd9d4r-010 not use your hands. Use items such as paper...
  • Page 93: Battery

    GM2810A Handling Instructions Inspecting the exterior Outer element Visually inspect the exterior of the battery, Inner element and check that there are no cracks, splits, Clip missing sections, or abnormal deformation Air cleaner cap in the battery case, and that there is no electrolyte leaking.
  • Page 94 GM2810A Handling Instructions Inspecting the electrolyte level and refilling Danger Warning When you supply battery fluid, wear protective Do not allow the battery fluid level to become garments and safety glasses, etc. lower than the LOWER LEVEL (minimum fluid level line).
  • Page 95: Electrical Wiring

    GM2810A Handling Instructions Electrical Wiring Belt Inspection of Electrical Wiring Inspection of Belt Important Warning Electrical short circuit will cause fire, electrical The engine must be stopped when the belt is leakage and malfunction of electrical inspected. equipments. Important Make sure that there is no defacement in wires and terminals.
  • Page 96: Around The Engine

    GM2810A Handling Instructions Position the machine so that the engine will Around The Engine be level, and then insert the oil level gauge all the way to check the oil level. Inspection of Engine/DPF-Associated Parts Caution Implement after the engine and DPF etc. have well cooled down.
  • Page 97: Fuel

    GM2810A Handling Instructions Fuel Supply of Engine Oil Inspection of Fuel Important With the machine on a level surface, check Do not supply too much engine oil. Otherwise, “FUEL LEVEL” in the monitor. the engine may be damaged. If the fuel level is low, supply diesel fuel.
  • Page 98 GM2810A Handling Instructions Fuel Supply Warning Do not supply additional fuel after "FUEL LEVEL" indicates 100 %. If you supply too much fuel, it might overflow from the fuel cap when you travel or work on a slope. Warning Keep fire away while refueling.
  • Page 99: Water Separator

    GM2810A Handling Instructions Air Bleeding of Fuel System Open the hood. Set the key switch to the "ON" position and then start the electromagnetic pump. A priming pump is installed on the feed pump. Repeatedly press the top of the priming pump with your finger until resistance is felt, to bleed air.
  • Page 100: Fuel Filter

    GM2810A Handling Instructions Fuel Filter Float Inspection of Fuel Filter Water drain plug Make sure that there is no fuel leakage. Element Make sure that the filter is not damaged. Air-bleeding bolt Make sure that the filter is not Tighten the water drain plug and air- contaminated.
  • Page 101: Adjustment Before Work

    GM2810A Handling Instructions Adjustment before Work Inspection of Wheel Mounting Bolt Adjustment of Steering Wheel Position Important Tighten the wheel mounting bolts on the Warning specified torque by using a torque wrench. Since it is dangerous, do not adjust the steering wheel while traveling.
  • Page 102: Adjustment Of Seat Position

    GM2810A Handling Instructions Adjustment of Seat Position Adjustment of Cutting Height Cutting Height Table Warning The adjustment range for the cutting height is Do not make an adjustment while traveling 20.0 - 91.5 mm (0.79 - 3.60 in). since it is dangerous.
  • Page 103 GM2810A Handling Instructions To decrease cutting height: Adjustment With Adjusting Collars Remove a lower adjusting collar and insert it above. Adjusting collars are installed at three locations on each mower deck. Important The length of grass cut off at any one time must be no more than 30.0 mm (1.18 in).
  • Page 104 GM2810A Handling Instructions Adjustment With Cutting Height Adjusting Plates Cutting height adjusting plates are installed at three locations on each mower deck. Important The length of grass cut off at any one time must be no more than 30.0 mm (1.18 in).
  • Page 105: Start/Stop Of Engine

    Switch the ignition key to the "ON (GLOW)" result in damage to the machine. position. After the "BARONESS" logo and the yellow and red LEDs go off and the parameters (items and values such as the rotation speed) appear, immediately set the ignition key to the "START"...
  • Page 106: Parking And Stopping

    GM2810A Handling Instructions When the starter starts rotating and the Move engine starts, slowly return the ignition key to the "ON" position. Traveling Procedure Important Caution Be sure to warm up the engine. Under any circumstances drive the machine at...
  • Page 107: Cutting Work

    GM2810A Handling Instructions Set the knife rotation switch to the "Rotation" Cutting Work position to rotate the rotary knives of all mower decks. Cutting Operation Depress the traveling pedal to start cutting work. Caution Note: When working on a slope, be sure to use the During the work, the rotary knives will rotate or machine in 4WD.
  • Page 108 GM2810A Handling Instructions Page 5-24 Transporting...
  • Page 109: Maintenance

    GM2810A Maintenance Precautions for Maintenance ....Page 6-2 Jacking Up The Machine .......Page 6-2 About Jacking Up The Machine .....Page 6-2 Jack-Up Points ........Page 6-2 Greasing ..........Page 6-3 About Greasing ........Page 6-3 Greasing Points ........Page 6-3 Lubrication ..........Page 6-6 About Lubrication ........Page 6-6...
  • Page 110: Precautions For Maintenance

    First, learn well the operations you plan to perform. Important Use tools appropriate for each operation. Important Use Baroness genuine parts for replacement and accessories. Our product warranty may be void if you use non-genuine parts for replacement or accessories.
  • Page 111: Greasing

    GM2810A Maintenance Front right frame Greasing About Greasing Since there may be adhesion or damage due to lack of grease on moving parts, they must be greased. Add urea-based No. 2 grease in accordance with the Maintenance Schedule. Other locations where the specified grease or lubricant is used are indicated in "Greasing...
  • Page 112: Greasing Points

    GM2810A Maintenance Lift arm fulcrum No. of There is one greasing point on the arm Portion Greasing   connected to each mower deck. Points Lower the mower decks before greasing the Mower arm fulcrum lift arm fulcrums. Lift arm fulcrum...
  • Page 113 GM2810A Maintenance Lift arm cylinder fulcrum Rear left wheel This is on each cylinder of the arms connected to each mower deck. Mower decks #1, #4 and #5 There are two greasing points on each cylinder. 8bq62b-033 Greasing Points_010 Rear right wheel...
  • Page 114: Lubrication

    GM2810A Maintenance Traveling pedal shaft fulcrum Lubricating Points There are two locations. Apply lubricant at the following locations every 50 hours of operation. 8bq62b-036 Greasing Points_013 Foot brake 8bq62b-500 There are three locations. Lubricating Points_001 No. of   Location lubricating...
  • Page 115: Adjustment And Replacement

    GM2810A Maintenance Fully insert the grip pin into the locking hole Adjustment and Replacement for maintenance, and then install the clip pin in the grip pin. Swiveling Mower Decks #2 and #3 Caution The rotary knife is an edged tool.
  • Page 116: Change Of Rotary Knife

    GM2810A Maintenance If the edge of the rotary knife becomes chipped Change of Rotary Knife or thin, replace it with a new one. The criteria for replacing the rotary knife are Caution described below. The rotary knife is an edged tool.
  • Page 117 GM2810A Maintenance Mower Deck #1 Start the engine, and then raise the mower decks. Stop the engine, and then remove the key. Lift the mower deck at the front. to41g1-007 Mower Deck #1_003 Square pipe Rotary knife Bolt Spring washer...
  • Page 118 GM2810A Maintenance Remove the cotter pin and hardened Important roundhead pin inserted at a, and then insert them at b. The tightening torque for the knife mounting bolt is 104 - 134 N-m (1,060.49 - 1,366.40 kgf- cm). Install the rotary knife.
  • Page 119: Grinding Of Rotary Knife

    GM2810A Maintenance Follow the steps below to remove the rotary Grinding of Rotary Knife knife. Use the square pipe from the included Caution tools to secure the rotary knife so that it The rotary knife is an edged tool. does not turn.
  • Page 120 GM2810A Maintenance When, after grinding, the blade base of the Important rotary knife does not reach the sail Grind only the top surface of the edge, and be sure to maintain the original angle. By equally grinding the left and right ends of the rotary knife, it can be sharpened without becoming imbalanced.
  • Page 121: Balancing Of Rotary Knife

    GM2810A Maintenance Balancing of Rotary Knife Replacement of Tires Replacement of Front Tires Caution Removing front tires The rotary knife is an edged tool. Follow the steps below to remove the front Take extra care in handling since they could tires: cut your hands or legs.
  • Page 122: Adjustment Of Belt Tension

    GM2810A Maintenance Adjustment of Belt Tension Replacement of Rear Tire Removing rear tires Warning Follow the steps below to remove the rear tire. Be sure to stop the engine before adjusting the belts. Loosen the bolts. Important For the specified value of belt tension, refer to Adjusted Values.
  • Page 123 GM2810A Maintenance Be sure to tighten the bolts A and B Be sure to tighten the bolts A and B securely after adjustment. securely after adjustment. mzdn8n-003 0E85A5FE Adjustment of Fan Belt_001 Adjustment of Fan Belt_002 Fan belt Fan belt...
  • Page 124: Change Of Coolant

    GM2810A Maintenance Change of Coolant LLC concentration Freezing temperature (volume %) Down to -10 °C (14 °F) 20 % Caution Down to -15 °C (5 °F) 30 % Do not touch the radiator or coolant during Down to -20 °C (-4 °F)
  • Page 125: Replacement Of Hydraulic Oil

    GM2810A Maintenance Remove the reserve tank. Important When you change the hydraulic oil, be sure to drain it into a bowl and discard it in accordance with local laws and regulations. Important If the oil emulsifies or if it becomes even slightly less transparent, change the oil immediately.
  • Page 126 GM2810A Maintenance Wind new sealing tape on the drain plug, and then attach it to the hydraulic tank. 0A2C6785 Replacement of Hydraulic Oil_003 k9yr5z-002 Tank cap Replacement of Hydraulic Oil_001 Oil gauge Hydraulic tank Oil filler plug Drain plug Air breather Bushing Remove the left tank cover.
  • Page 127: Change Of Hydraulic Oil Filter

    GM2810A Maintenance Firmly tighten the filter cartridge by hand Change of Hydraulic Oil Filter until the packing contacts the mounting surface. Change of Hydraulic Oil Line Filter And then tighten it with a half more turn. Caution Be careful with hot oil, which could cause burns if it contacts your skin.
  • Page 128 GM2810A Maintenance Install the intake hose joint fitting to the Change of Hydraulic Oil Suction Filter hydraulic tank. Caution Be careful with hot oil, which could cause burns if it contacts your skin. Important When replacing the hydraulic oil filter, be sure to drain the oil into a container and discard it in accordance with local laws and regulations.
  • Page 129: Replacement Of Air Breather Element

    GM2810A Maintenance Install the new element. Replacement of Air Breather Element Important Caution If the seal washer is damaged, replace it with a new one. Be careful with hot oil, which could cause burns if it contacts your skin. Install the top cover of the air breather.
  • Page 130: Change Of Engine Oil

    GM2810A Maintenance Through the oil filling port, supply new Change of Engine Oil engine oil until the oil reaches a level in between the upper and lower limit lines on Caution the oil level gauge. Engine oil quantity is approximately 9.7 dm Be careful with hot oil, which could cause (9.7 L).
  • Page 131: Replacement Of Engine Oil Filter

    GM2810A Maintenance Make sure that there is no oil leakage at the Replacement of Engine Oil Filter sealing surface of the filter cartridge. Check the engine oil level. Caution If it is low, supply engine oil until it reaches Be careful with hot oil, which could cause the specified level.
  • Page 132: Storage

    GM2810A Maintenance Lightly coat the packing of the new Storage location cartridge with fuel, and then firmly hand- Cover the machine and store it in a dry ・ tighten the cartridge, without using the place where it will not be exposed to rain.
  • Page 133: Repair

    GM2810A Repair Precautions for Repair ......Page 7-2 Adjustment and Replacement ....Page 7-2 Adjustment of Brake ......Page 7-2 Adjusting the Neutral Position of the Piston Pump .......... Page 7-4 Replacement of Fuse ......Page 7-4 Towing .............Page 7-5 Towing The Machine in An Emergency ..........Page 7-5...
  • Page 134: Precautions For Repair

    (neutral). For each wheel, fully tighten the adjustment Important bolt on the brake disc side. Use Baroness genuine parts for replacement and accessories. Our product warranty may be void if you use non-genuine parts for replacement or accessories.
  • Page 135 GM2810A Repair Reduce the clearance by loosening the lock Inner wire nut, then tightening the adjustment nut. Adjustment bolt Tighten the adjustment nut until the friction Lock nut material contacts the friction surface of the Connection disc. 1.0 mm (0.039 in)
  • Page 136: Adjusting The Neutral Position Of The Piston Pump

    GM2810A Repair Adjusting the Neutral Position of the Piston Lock nut A (Left-hand thread) Pump Neutral adjustment rod Lock nut B (Right-hand thread) Caution Find the position where the front wheels Make sure not to touch rotating tires. stop, and then tighten the lock nuts.
  • Page 137: Towing

    GM2810A Repair Towing Towing The Machine in An Emergency If the machine does not travel due to engine A B C D E problems, etc., you can move it by towing it. H I J Caution Before towing, check the brake is applied effectively.
  • Page 138 GM2810A Repair Secure the machine with ropes. Turn the needle valve 90 degrees (so that it Front left side is vertical) located beside the hydraulic pump, to open the unload valve. gay3t1-024 Towing The Machine in An Emergency_001 gay3t1-005 Front right side...
  • Page 139: Appended Table

    GM2810A Appended Table Tightening Torques ........Page 8-2 Standard Tightening Torques ....Page 8-2 Principal Tightening Torques ....Page 8-5 Maintenance Schedule ......Page 8-7 List of Adjusted Value ......Page 8-12 List of Fault Codes ......Page 8-13 Page 8-1...
  • Page 140: Tightening Torques

    GM2810A Appended Table Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine.
  • Page 141 GM2810A Appended Table General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49...
  • Page 142 GM2810A Appended Table Hydraulic Hose The tightening torques for union joints and union adaptors with parallel pipe threads (G, PF) are shown in the table below. A union joint or adaptor will not become loose or leak as long as it is tightened by the specified torque.
  • Page 143: Principal Tightening Torques

    GM2810A Appended Table Principal Tightening Torques Tightening Torque by Model GM2810A Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant).
  • Page 144 GM2810A Appended Table Tightening torque Thread locking Location Code Part name adhesive kgf-cm lb-in Bolt, w/hexagon hole, K001A100401 815.76 708.08 ○ M10-40 Joint 458.87 - 398.30 - K0013100352 Bolt, heat-treated M10-35 45 - 76 - 774.97 672.68 530.24 - 460.25 -...
  • Page 145: Maintenance Schedule

    GM2810A Appended Table Maintenance Schedule GM2810A ●・・・Inspect, adjust, supply, clean (first time) ○・・・Inspect, adjust, supply, clean ▲・・・Replace (first time) △・・・Replace Maintenance Item Remarks Check engine oil level ○                              ...
  • Page 146 GM2810A Appended Table Maintenance Item Remarks Replace every 6 cleanings or every year whichever Clean air cleaner outer comes earlier element (Replace the         ○               △       Air cleaner should...
  • Page 147 GM2810A Appended Table Maintenance Item Remarks Initial 50 hours, thereafter every Replace oil filter 400 hours or every       ▲     △           △       cartridge year whichever comes earlier Replace fuel filter *1.*4...
  • Page 148 GM2810A Appended Table Maintenance Item Remarks Check DPF differential *2.*4 pressure pipes and                         ○         hoses *2.*4 Check EGR piping                         ○      ...
  • Page 149 *1: When biodiesel fuel is used, replace the fuel filter cartridge, fuel hose and clamp bands with new ・ ones at intervals half of the usual ones. *2: Consult your local Baroness Dealer or local KUBOTA Dealer for this service. ・ ・...
  • Page 150: List Of Adjusted Value

    GM2810A Appended Table List of Adjusted Value Slack when applying 98 N (10 kgf) force to 10.0 - 12.0 mm (0.39 - 0.47 in) the belt at the middle point Fan belt Adjustment: 237 - 403 N Measurement of belt tension by using a...
  • Page 151: List Of Fault Codes

    GM2810A Appended Table List of Fault Codes 03StageV J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Large phase shift between NE •...
  • Page 152 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Lack of fuel (This error occurs when the engine stalls due...
  • Page 153 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Diagnostic • Open circuit or • Amount of counter = 0 【P0113】Intake...
  • Page 154 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Insufficient output • Worsening • Output exhaust gas • Open circuit or limitation•...
  • Page 155 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Diagnostic • Output counter = 0 • Insufficient • Overheat of limitation•...
  • Page 156 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Diagnostic • Open circuit or (Invalid G signal) counter = 0 short circuit of 【P0341】G...
  • Page 157 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Insufficient • Output output 【P0409】EGR limitation• • EGR position • Key switch turn...
  • Page 158 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Diagnostic • Output counter = 0 【P0602】QR limitation• • QR data read •...
  • Page 159 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Insufficient • Output output limitation• Speed • Worsening 【P0629】 +Battery limitation•...
  • Page 160 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Faulty starting • Output • Insufficient • Sensor supply 【P0652】Sensor limitation•...
  • Page 161 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Diagnostic counter = 0 【P2123】 • Forced Idle• • Battery short Accelerator •...
  • Page 162 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Insufficient output • Engine 【P2147】Ground • Output Vibration short at injector limitation•...
  • Page 163 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Insufficient output 【P2151】 +Battery • Output • Large vibration short at injector limitation•...
  • Page 164 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Insufficient • Output • EGR (DC 【P2415】EGR output (DC motor) limitation•...
  • Page 165 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) 【P3002】 • Engine stops • Engine forcibly Emergency • DOC inlet •...
  • Page 166 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Diagnostic • During counter = 0 regeneration (returns when mode, engine 【P3012】Low...
  • Page 167 GM2810A Appended Table J1939-73 English English LED ON Limp home Behavior P code action by engine DTC recovery Description Detection item During Yellow ECU (System from error Malfunction action) • Diagnostic • Worsening counter = 0 • Regeneration • Coolant...
  • Page 168 GM2810A Appended Table Page 8-30 List of Fault Codes...
  • Page 169 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Aichi-pref, 442-8530 JAPAN Fax : +81 - 533 - 84 - 1220 GM2810A-UM--GBZ/24B-00-S.K...

Table of Contents