Panasonic MC-V9620 Operating Instructions Manual page 14

TROUBLESHOOTING
Review this chart to find do-it-yourself solutions for minor performance problems.
A WAR N I N G Electrical Shock Hazard
Disconnect electrical supply before servicing or cleaning the unit. Failure to do so
could result in electrical shock or personal injury.
PROBLEM
Cleaner won't start.
POSSIBLE CAUSE
1. Unplugged at wall outlet.
2. Tripped circuit breaker/blown
fuse at household service panel.
3. Loose hose electrical connections.
4. Tripped Overfoad Protector
in POWER NOZZLE.
5. On-Off switch not tumed ON.
. Full or clogged dust bag
or airflow blockage.
POSSIBLE SOLUTION
. Plug in firmly, push On/Off switch to ON.
Reset circuit breaker or repiace fuse.
Reconnect hose ends, (page 4}.
. Clean brush and brush supports,
then reset, (pages 9,10,1 1
5. Push On-Off switch to ON.
1. Change bag, (page 8) Clean
airflow passage, (page 4).
Bp
be
Poor job of dirt pick-up.
2. Dirty motor safety filter. 2. Clean filter, (page 8).
3. Wrong pile height setting. 3. Adjust setting, (page 5).
4. Open suction control, 4. Adjust control, (page 7).
5. Hole ín hose. 5. Replace hose.
6. Worn POWER NOZZLE brushes, 6. Change agitator unit, (page 11).
7. Clogged POWER NOZZLE nozzle. 7. Clean POWER NOZZLE air passage.
8. Clogged handle or hose. 8. Clean air passage.
9. Canister hood open. 9. Close and latch hood.
10. POWER NOZZLE not running. 10. Check overload protector button.
Reset POWER NOZZLE, (page 7).
1. Check connections, reconnect
hose ends, (page 4).
2. Remove any iterns that may be
caught or jammed, then reset,
If the cleaner starts and stops
again, clean brush and brush
supports, then reset, (pages 9,10,11).
3. Wait 20 minutes for motor to cool.
4. Change dust bag, (page 8) Clear
airflow blockage, (page 4). Wait
20 minutes for motor to cool.
1. Plug in firmly, (page 5).
2. 8 3. See "BELT CHANGING AND
BRUSH CLEANING." (pages 9,10,11).
4. Check brush area for excessive
lint build-up or jamming. Clean
brush and brush supports, then
reset, (pages 9,10,1 4).
Cleaner picks up movable | 1. Wrong pile height setting. | 1. Adjust setting, (раде 5).
rugs -OR- POWER 2. Suction too strong. 2. Open suction control, (page 7).
NOZZLE pushes to hard.
Light won't work. 1. Bumed out bulb. 1. Change bulb, (page 9).
Cord won't rewind. 1. Dirty power cord. 1. Clean the power cord.
2. Cord locked in cord grip. 2. Remove cord from grip.
3. Cord jammed. 3. Pull out cord and rewind.
Cleaner leaves marks 1. Wrong vacuuming pattern. 1. See "VACUUMING TIPS," (page 7).
on carpet.
49=
Cleaner starts but . Hose or hood electrical
cuts off. connections.
2. Tripped Overload Protector
in POWER NOZZLE.
3. Motor too hot.
4, Fult or cl god dust bag
or airflow blockage.
POWER NOZZLE will not
run when attached.
. POWER NOZZLE connections
unplugged.
2. Worn or broken belt.
3. Dirty brush or brush supports.
4, Tripped Overload Protector
in POWER NOZZLE.