Page 1: Table Of Contents
DNE4500-P and DNE4500-S DS3 Network Extenders Installation Instructions Document Number DNE4-A2-GN10-00 August 2005 Contents Software and Firmware License Agreement Product Documentation Online Package Contents Powering Up the DNE4500 Verifying the Switch Configuration Connecting the DS3 Line Connecting the Ethernet Line...
Page 2 The terms and conditions of this License Agreement (the “Agreement”) will apply to the software and/or firmware (individually or collectively the “Software”) incorporated into the Paradyne product (the “Product”) purchased by you and any derivatives obtained from the Software, including any copy of either. If you have executed a separate written agreement covering the Software supplied to you under this purchase, such separate written agreement shall govern.
Page 3: Product Documentation Online
7. The rights granted under this Agreement may not be assigned, sublicensed or otherwise transferred by the Licensee to any third party without the prior written consent of Paradyne. 8. This Agreement and the license granted under this Agreement shall be terminated in the event of breach by the Licensee of any provisions of this Agreement.
Page 4: Powering Up The Dne4500
Switches are numbered from left to right; Switch 1 is on the left and Switch 2 is on the right. Switch 1 is not used on the subscriber unit (DNE4500-S). Clock source configuration for the DNE4500-S is determined by the switch setting on the provider unit (DNE4500-P). Clock Source Switch Configuration Switch 1...
Page 5: Connecting The Ds3 Line
DS3 connection is established and operational. A DS3 network extender subscriber unit (DNE4500-S) must be connected via DS3 line to a DS3 network extender provider unit (DNE4500-P or DNE4500-P-6-AC/DC). A subscriber-to-subscriber or provider-to-provider connection will not function.
Page 6: Led Indicators
LED Indicators Table 1. LED States (1 of 3) State flashing Connection green* solid green illumination Connection illumination solid amber pulsing amber Indication Additional Information DS3 is operational The DS3 connection has been established and traffic is flowing. DS3 link is A connection exists but there is established indication of a problem with the...
Page 7 Table 1. LED States (2 of 3) State Power solid green Fast Ethernet solid green illumination Fast Ethernet pulsing amber solid amber illumination Indication Additional Information Unit is operational If the Power LED is not illuminated, it is likely that the DNE4500 is not receiving power and therefore none of the LEDs will be illuminated.
Page 8 Table 1. LED States (3 of 3) State Fast Ethernet solid green illumination A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a more rapid, less constant rate. Indication Additional Information Ethernet connection If the Fast Ethernet Lnk LED is is established illuminated but not the Fast...
Page 9: Fast Ethernet Connector Pinouts
Fast Ethernet Connector Pinouts Fast Ethernet Port Table 2. Fast Ethernet (RJ45) Port Connection Rx– not used not used Tx– not used not used EMI Notices United States – EMI Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
Page 10: Acta Customer Information
Canada – EMI Notice This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. ACTA Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
Page 11: Ce Marking
CE Marking When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → Technical Manuals → Conformity. Japan Notice Class A ITE This is a Class A product based on the standard of the Voluntary Control Council for interference by Information Technology Equipment (VCCI).
Page 12 7. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement corrective action prior to interconnecting the products.

This manual is also suitable for:

Dne4500-s

Paradyne DNE4500-P Installation Instructions Manual

Quick Links

Software and Firmware License Agreement

Related Manuals for Paradyne DNE4500-P

Summary of Contents for Paradyne DNE4500-P

This manual is also suitable for:

Table of Contents