Maintenance - Black & Decker BCSS20D1 Manual

For best results when using this accessory, hold the appli-
u
ance at an angle of 45° and pull it slowly towards you.
ENGLISH
u
there is any liquid in the bowl, do not turn the unit upside
down, sideways, point the nozzle upward, or shake the
Use the trimmer only for cutting normal shrubbery around
vac excessively.
houses and buildings.
After picking up liquid substances clean the appliance and
To turn the tool "ON", shift the lock off switch (2) and squeeze
u
the trigger switch (1) . Once the unit is running, you may
not properly cleaned after wet pickups.
release the lock off switch.
Before charging, be sure to empty all liquid contents and
To turn the tool "OFF", release the trigger.
u
dry thoroughly, to avoid damage to your appliance.
Hints for optimum use (Figs. E, F, G, H, I)
Optimising the suction force
Trimming grass (Fig. E, F )
cleared regularly during use.
Warning! Blades coast after turn off.
In order to achieve optimum cutting results, only cut
u
Emptying and cleaning the product.
dry grass.
Hold the tool as shown in Fig. G. Keep your other hand
u
well away from the blade. Maintain a stable working
Warning!
position so that you do not slip. Do not overreach.
regularly.
When cutting long grass, work in stages from the top. Take
u
Press the bowl release button (2) and pull the dust bowl
small cuts.
u
(3) straight off.
Keep the tool away from hard objects and delicate plants.
u
While holding the dust bowl over a bin or sink, pull out the
If the tool starts running slowly, reduce the load.
u
u
To make a closer cut, slightly tilt the tool.
u
To replace the dust bowl, place it back onto the handle
u
Trimming hedges (Fig. G, H, I)
Warning!
Warning! Blades coast after turn off.
Slightly tilt the tool (up to 15° relative to the line of cut) so
u
that the blade tips point slightly towards the hedge. This
G
will cause the blades to cut more effectively.
Place the foam insert (6) into the centre of the wet/dry
Start by trimming the top of the hedge.
u
u
7
Hold the tool at the desired angle and move it steadily
u
Warning! Never use the appliance for wet applications without
along the line of cut. The double-sided blade allows you
to cut in either direction.
In order to obtain a very straight cut, stretch a piece of
u
string along the length of the hedge at the desired height.
Use the string as a guide line, cutting just above it.
In order to obtain flat sides, cut upwards with the growth.
u
Younger stems move outwards when the blade cuts
downwards, causing shallow patches in the hedge.
Take care to avoid any foreign objects.
u
Especially avoid hard objects such as metal wire and
railings, as these could damage the blades.
Regularly oil the blades.
u

Maintenance

Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
8
(Original instructions)
ever worn or damaged.
dealer.
Warning! Before performing any maintenance on the tool,
Maintenance
switch off the tool. Unplug the charger before cleaning it.
Your BLACK+DECKER corded/cordless appliance/tool has Regularly clean the ventilation slots in your tool and
u
been designed to operate over a long period of time with a charger using a soft brush or dry cloth.
minimum of maintenance. Continuous satisfactory operation Regularly clean the motor housing using a damp cloth.
u
depends upon proper tool care and regular cleaning. Do not use any abrasive or solvent-based cleaner.
Warning! Before performing any maintenance on corded/ After use, carefully clean the blades. After cleaning, apply
u
cordless power tools: a film of light machine oil to prevent the blades from
rusting. Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
Storage
tool if the appliance/tool has a separate battery pack.
When the tool will not be used for several months, ideally leave Or run the battery down completely if it is integral and then
u
the battery connected to the charger. Otherwise proceed as switch off.
follows: Unplug the charger before cleaning it. Your charger does
u
Fully charge the battery. not require any maintenance apart from regular cleaning.
u
Store the tool in a secure and dry location. The storage Regularly clean the ventilation slots in your appliance/tool/
u u
temperature must always remain in the range of +5 °C to charger using a soft brush or dry cloth.
+40 °C. Regularly clean the motor housing using a damp cloth. Do
u
Before using the tool after prolonged storage, fully charge not use any abrasive or solvent-based cleaner.
u
the battery again.
Protecting the environment
Protecting the environment
Z
Separate collection. Products and batteries marked
Separate collection. Products and batteries
-
with this symbol must not be disposed of with normal
marked with this symbol must not be disposed of
household waste.
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions.
Technical data
Voltage
Blade Length (shear)
Blade gap (shear)
Blade Length (trimmer)
Blade gap (trimmer)
Weight
Batteries
Vdc Weight
Cat# Ah
Kg
BL1518 18 1.5 0.38
BL1518ST 18 1.5 0.38
BL2018 18 2.0 0.39
BL2018ST 18 2.0 0.39
BL2518 18 2.5 0.43
BL4018 18 4.0 0.64
V
cm
mm
cm
mm
kg
Charger (minutes)
Cat# N588726* N517388* BDC1A
Amps 400mA 1A 1A
BL1518 225 90 90
BL1518ST 225 90 90
BL2018 300 120 120
BL2018ST 300 120 120
BL2518 380 150 150
BL4018 600 240 240
-
BCSS20
18 (20 Max)
10
23
20
8
0.84
7
BDC2A BDC2A36
2A 1.35A
25 X
45 X
60 X
60 X
75 X
120 X