Table of Contents
Advertisement
Quick Links
SERVICE BULLETIN
Document ID:
SB254
Title:
Receiver Retrofit for Programmable
Remote
Affected machinery: RailRider Pro
Distribution: Customers upon order
Applies to: All machines with frequency-specific remotes and matching receivers built before
April 2022
CAUTION:
MiTek recommends printing
this manual in high resolution
using color ink. Many of the
graphics may be unclear and
may create an unsafe condition
if this recommendation is not
followed.
MiTek Automation
Phone: 800-523-3380
Fax: 636-328-9218
www.mitek-us.com
®
Copyright © 2024 MiTek
. All rights reserved.
®
Floor Truss Press
Part # and Rev.
Print Date
Revision Date
Revised By
Orig. Release Date
Created By
Approved By
SB254 rev. A
2024 January 31
2024 January 31
A. McIntire
2022 December 9
A. McIntire
R. Tucker
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mitek RailRider Pro
Summary of Contents for Mitek RailRider Pro
- Page 1 Document ID: SB254 Title: Receiver Retrofit for Programmable Remote ® Affected machinery: RailRider Pro Floor Truss Press Distribution: Customers upon order Applies to: All machines with frequency-specific remotes and matching receivers built before April 2022 CAUTION: Part # and Rev.
-
Page 2: Purpose And Scope
SB254 REV. A Purpose and Scope This service bulletin instructs how to install new receivers on the RailRider Pro to enable compatibility with new remote (transmitter) types. It also covers how to program a remote to a specific receiver. If the package containing the receiver and remotes... -
Page 3: Electrical Lockout/Tagout Procedure
Installing the New Receivers This section covers how to install one or more new receivers for a RailRider Pro. 1. With the power locked out as previously described, access the stand- alone electrical enclosure and see sub-steps to determine which wiring... - Page 4 SB254 REV. A b) If you have a machine with pushbuttons and a remote (see Figure 2) disconnect the wires shown in Table 4 for the single receiver. Figure 2: Pushbutton Example Table 3: Wiring Chart for Receivers 1 and 2 (remotes only setup) Wiring Chart for Receiver 1 Wiring Chart for Receiver 2 Cable...
- Page 5 SB254 REV. A 2. Remove receivers 1 and 2 (4 bolts each) from each side of the enclosure and retain all bolts for a later step. • Note that some setups may have only 1 receiver. Figure 3: Receivers on Electrical Enclosure Receiver 2 Receiver 1 3.
- Page 6 1. Disconnect power to one of the receivers by removing the fuse from the RailRider Pro main electrical enclosure (see Figure 4). Make note which fuse is pulled as the other fuse must be pulled to pair the second pair of remotes to the other receiver.
- Page 7 SB254 REV. A See Figure 5 for a depiction of the remote buttons to be used during the pairing procedure. Figure 5: Remote Pairing Buttons STOP • All references to the buttons in the following instructions refer to only the remote.
- Page 8 SB254 REV. A 7. Disconnect power to the receiver via fuse. 8. Reconnect power to the receiver via fuse. 9. In quick succession, press SET and then F1, holding both until the receiver LED stops flashing. 10. In quick succession, release F1 and then SET. 11.
- Page 9 SB254 REV. A 13. Repeat the pairing process for the other receiver (and 2 remotes) if necessary. Operating the Hand-Held Remote and Keypad This procedure applies to both the hand-held remote and the keypad located on the receiver. They both transmit a signal to the receiver. CAUTION A hand-held remote should only be used within line-of-sight of the machine and at a maximum distance no greater than 100 ft.
- Page 10 SB254 REV. A 2. Press the yellow button Figure 7: Operating the Remote that corresponds to the desired action, using Indicator these rules: Light • Press once and release. Press again Power Off Power On within 5 seconds and hold for 1 second, then Eject Up Eject Down the operation will...
Need help?
Do you have a question about the RailRider Pro and is the answer not in the manual?
Questions and answers