Table of Contents
Advertisement
12
nn
10
1
00,08,09,0A
28,29,2A,2B,
2C,2D
TOTAL
SIZE
01
If data other than the above is received, 0:stereo out will be selected.
Note: In the case of OUTPUT SELECT, if the received value exceeds the number that can be supported, the parameter value will be 0.
n:Audio Part number( 0 - D )
< Table 1 - 8 >
MIDI Parameter Change table ( Audio Part Configuration )
Address
Size Data
(H)
(H)
(H)
11
0n
00
1
00 - 01
TOTAL
SIZE
01
11
0n
01
3
00 -
00 -
00 -
TOTAL
SIZE
03
n:Audio Part number( 0 - D )
< Table 1 - 9 >
MIDI Parameter Change table ( DRUM SETUP )
Address
Size Data
(H)
(H)
(H)
3n
rr
00
1
00 - 7F
01
1
00 - 7F
02
1
00 - 7F
03
1
00 - 7F
04
1
00 - 7F
05
1
00 - 7F
06
1
00 - 7F
07
1
00 - 7F
08
1
00 - 01
09
1
00 - 01
0A
1
00 - 01
0B
1
00 - 7F
0C
1
00 - 7F
0D
1
00 - 7F
0E
1
00 - 7F
0F
1
00 - 7F
TOTAL
SIZE
10
3n
rr
20
1
00 - 7F
21
1
00 - 7F
22
1
23
1
24
1
04 - 28
25
1
1C - 3A
26
1
27
1
28
1
29
1
2A
1
2B
1
2C
1
2D
1
TOTAL
SIZE
0E
3n
rr
40
1
00,08,09,0A
28,29,2A,2B,
2C,2D
TOTAL
SIZE
01
When data other than the above is received, 0:stereo out will be selected.
3n
rr
50
1
00 - 7F
51
1
TOTAL
SIZE
02
3n
rr
60
1
30 - 50
61
1
30 - 50
TOTAL SIZE
02
n:Drum Setup Number(0 - 3)
rr:note number(0D - 5B)
In the following cases, the SW1000XG will initialize all Drum Setups.
XG SYSTEM ON received
GM SYSTEM ON received
DRUM SETUP RESET received (when in XG mode)
OUTPUT SELECT
Parameter
Stereo/Monaural
Input Category
Input Sub Category
Input Serial Number
Parameter
PITCH
COARSE
PITCH
FINE
LEVEL
ALTERNATE
GROUP
PAN
REVERB
SEND
CHORUS
SEND
VARIATION SEND
KEY ASSIGN
Rcv NOTE
OFF
Rcv NOTE
ON
LOW PASS FILTER
CUTOFF
FREQUENCY
LOW PASS FILTER
RESONANCE
EG
ATTACK RATE
EG
DECAY1 RATE
EG
DECAY2 RATE
EQ BASS GAIN
EQ TREBLE GAIN
NOT USED
NOT USED
EQ BASS FREQUENCY
EQ TREBLE FREQUENCY
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
OUTPUT SELECT
HIGH PASS FILTER CUTOFF FREQUENCY
NOT USED
VELOCITY SENSE PITCH
VELOCITY SENSE LPF CUTOFF
0:stereo out, 8:indiv1+2, 9:indiv3+4, 00
10:indiv5+6,40:indiv1,41:indiv2,42:indiv3,
43:indiv4, 44:indiv5,45:indiv6
Description
Switch between Stereo and Monaural 00
(Effective only for even numbered
parts)
Indicate input type,
depending on the shape of
the connector.
0:No Connection
1 63:Connection to external device
1:Analog,others: Reserve
64 126:Connection to internal Bus
64:PCI,others: Reserve
127:Reserve
Indicate input sub-type.
Not used at present. Set to 0.
Serial number in the same
input category.
Description
-64...0...+63
-64...0...+63[cent]
0...127
OFF,1...127
RND,L63...C...R63
0...127
0...127
0...127
SINGLE , MULTI
OFF , ON
OFF , ON
-64...0...63
-64...0...63
-64...0...63
-64...0...63
-64...0...63
-12 - +12[dB]
-12 - +12[dB]
32...2.0k[Hz]
500...16.0k[Hz]
0:stereo out, 8:indiv1+2, 9:indiv3+4, 00
10:indiv5+6,40:indiv1,41:indiv2,42:indiv3,
43:indiv4, 44:indiv5,45:indiv6
-64...0...63
-16...0...16
-16...0...16
81
Default value
(H)
00
00
00
Default value
(H)
40
40
depend on the note
7F
00
depend on the note
01
40
40
40
40
40
40
40
—
—
0C
36
—
—
—
—
—
—
—
—
40
—
depend on the note
Advertisement
Table of Contents
