Yamaha QY-70 Supplementary Manual page 45

SOFT PEDAL
NRPN
RPN
PORTAMENT CONTROL
The following data will not change.
PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN.
HARMONIC CONTENT, RELEASE TIME, ATTACK TIME, BRIGHTNESS, DRY SEND LEVEL,
EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3, EFFECT SEND LEVEL 4,
PITCH BEND SENSITIBITY, FINE TUNING, COURSE TUNING
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH , DATA VALUE = 0)
Turns off all notes of the corresponding channel which are on. However if Sustain or Sostenuto are on,
the sound will continue until these are turned off.
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH , DATA VALUE = 0)
Performs the same processing as when ALL NOTE OFF is received. Sets the VOICE RECEIVE CHANNEL
to OMNI OFF and CHANNEL = 1.
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH , DATA VALUE = 0)
Performs the same processing as when ALL NOTE OFF is received. Does not set OMNI ON. Sets the
VOICE RECEIVE CHANNEL to OMNI ON.
(3-2-6) MONO (CONTROL NUMBER = 7EH , DATA VALUE = 0)
Performs the same processing as when All SOUND OFF is received, and if the 3rd byte (mono number) is
in the range 0—16, sets the corresponding channel to Mode 4 (m=1).
If in the VOICE MODE, Mode 2 (m=1) is also possible, according to the VOICE RECEIVE CHANNEL.
(3-2-7) POLY (CONTROL NUMBER = 7FH , DATA VALUE = 0)
Performs the same processing as when ALL SOUND OFF is received, and sets the corresponding
channel to Mode 3.
When in the VOICE MODE, Mode 1 is also possible, according to the VOICE RECEIVE CHANNEL.
(3-3) REGISTERED PARAMETER NUMBER
STATUS
LSB
RPN LSB
MSB
RPN MSB
DATA ENTRY MSB
DATA VALUE
DATA ENTRY LSB
DATA VALUE
First transmit an RPN MSB and RPN LSB to specify the parameter that is to be controlled, then use Data
Entry to set the value of the specified parameter.
RPN D.ENTRY
LSB MSB MSB LSB
00H 00H mmH —
01H 00H mmH llH
02H 00H mmH —
7FH 7FH —
M I D I D a t a
0 (off)
Un-set status. Internal data will not change.
Un-set status. Internal data will not change.
reset
1011nnnn (BnH)
01100100 (64H)
0ppppppp
01100101 (65H)
0qqqqqqq
00000110 (06H)
0mmmmmmm
00100110 (26H)
0lllllll
PARAMETER NAME
PITCH BEND SENSITIVITY
MASTER FINE TUNE
MASTER COARSE TUNE
— RPN RESET
F o r m a t
n = 0 ~ 15 VOICE CHANNEL NUMBER
p = RPN LSB (Refer to the table on the following page.)
q = RPN MSB (Refer to the table on the following page.)
m = Data Value
l = Data Value
DATA RANGE
00H - 18H (0 - 24 semitones)
{mmH,llH} = {00H,00H} - {40H,00H} - {7FH,7FH}
(-8192*100/8192) - 0 - (+8192*100/8192)
28H - 40H - 58H (-24 - 0 - +24 semitones)
Set to a condition in which the RPN number is
unspecified.
Internal settings will not change.
45 45