Download Print this page

Message List - Yamaha DME24N Owner's Manual Supplement

Version 1.2
Hide thumbs Also See for DME24N:

Advertisement

Message List

Message
Cannot Select
CAS. In Sync Err
CAS. Out Sync Err
Connecting
Download Success
Downloading
DSP Power Shortage
Duplicate IP Adr.
File Operating
Flash Rom Full
Illegal MAC Adr.
Invalid IP Adr.
Invalid Password
Low Battery
MIDI Port In Use
Network Busy
Network Error
Network Setup
No Battery
No Current Scene
No MAC Adr.
Panel Locked
Panel Unlocked
Param Access Err
Param Set Err
6
Notes for DME64N/DME24N Version 1.2
Content
There is no selectable item in the scene or monitoring
point list.
The word clock input from the [CASCADE IN] terminal is
not synchronized with the DME64N word clock.
The word clock input from the [CASCADE OUT] terminal is
not synchronized with the DME64N word clock.
Searching for DMEs in the network and connecting them.
The DME64N/24N program update or restoration was
successful.
Updating the DME64N/24N program. Do NOT turn off the
power while this display is on the screen.
The audio signal is muted without being input or output,
because the DSP resources are insufficient. This message
may be displayed when a configuration created at 44.1 or
48 kHz is operated at 88.2 or 96 kHz.
An IP address is duplicated.
Scene-related data (configuration, component, etc.) from
the computer is in operation. Do NOT turn off the power
while this display is on the screen.
The flash memory used for saving data has become full.
This is an invalid MAC address.
An IP address is invalid.
The password is incorrect.
Battery capacity is running low.
The USB port being used for communication with DME
Designer has been selected as a host.
Traffic in the network is congested. Communication will
take time.
An error like the following has occurred on the network:
• A cable has become disconnected.
• The power to a connected hub or router is cut off.
• A cable is in an unsuitable condition (such as something
heavy resting on the cable).
(Static electricity may be having an effect.)
Various settings for connecting to the network are being
made.
The battery is exhausted.
There is no current scene.
No MAC address is set.
Panel lock is set, and the panel cannot be operated.
Panel lock has been cleared. Panel operations are
possible.
Cannot display current settings.
Cannot change current settings.
Corrective Action
Data is not registered.Register the data to be used in DME
Designer.
Recheck the settings for using the word clock that
synchronizes the DME64N and external devices.
Recheck the settings for using the word clock that
synchronizes the DME64N and external devices.
To operate with all word clocks, set the word clock in DME
Designer to 96 kHz when creating a configuration.
Change the settings so that there are no duplicate IP
address.
Erase unused data such as configurations, presets, and
audio data.
Since this is likely to be a device failure, contact a Yamaha
electric sound service outlet listed at the end of this
manual (page 79).
Set a valid IP address.
Enter the correct password. If you have forgotten the
password, contact a Yamaha electric sound service outlet
listed at the end of this manual (page 79).
Stop using the unit immediately and contact a Yamaha
electric sound service outlet listed at the end of this
manual (page 79).
Set Host on the utility screen's MIDI page to another port.
Check the devices connected to the network. If there are a
large number of connected devices, reduce their number.
If LinkMode is set to 10BASE-T, traffic speed may improve
if the setting is changed to 100BASE-TX.
Investigate the cause of the error and eliminate it.
When the power is turned OFF, the current settings will be
lost and the unit will return to its initial settings. Stop using
the unit immediately and contact a Yamaha electric sound
service outlet listed at the end of this manual (page 79).
This is displayed when scene data has not been sent even
once. Create data using DME Designer, and synchronize
DME Designer and the DME64N/24N unit.
Since this is likely to be a device failure, contact a Yamaha
electric sound service outlet listed at the end of this
manual (page 79).
Panel lock may have been set by the administrator to
prevent unexpected data changes caused by erroneous
user operations.
To use the panel, hold the [CANCEL] button down for at
least two seconds. This clears the panel lock.
The component version may be old. Update to the latest
component.
The component version may be old. Update to the latest
component.

Advertisement

loading

This manual is also suitable for:

Dme64n