Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Riester K-L.E.D.
Summary of Contents for Riester K-L.E.D.
- Page 1 Operating Manual K-L.E.D. System with charger Binocular loupes...
-
Page 2: Table Of Contents
INTRODUCTION Thank you for purchasing the Riester K-L.E.D. Headlamp. The product has been designed and manufactured to ensure that you will enjoy many years of trouble free and safe use. Please follow the User Instructions to ensure optimum performance. The headlamp has been designed to be used in dental and surgical environments, to illuminate areas under examination by the user. -
Page 3: Safety
FDA: Class I Carefully read this Instruction Section before using your Riester product. For your own safety and that of your customers observe all cautionary information provided in this section. The following information is intended to highlight potential safety hazards that can be associated with misuse, or damage. - Page 4 Use only genuine Riester approved parts and accessories or device safety and performance may be compromised. Use only Riester approved batteries, chargers and power supplies as per the accessories listed in section 11. Ensure the equipment is positioned in such a way that it can be disconnected from the mains easily.
-
Page 5: K-L.e.d. Headlamp With Single Battery Pack
3. K-L.E.D. HEADLAMP WITH SINGLE BATTERY PACK DESCRIPTION OF THE PRODUCT A Rechargeable Battery Pack B Power Supply and Adaptors C Battery Charger adlamp with Single Battery P ack D LED Light Source D. Headlamp with Single Battery P ack E Connector Headlamp with Single Battery P ack Product... -
Page 6: Charging The Single Battery Pack
CHARGING THE SINGLE BATTERY PACK The battery pack can be used at any time during the charging cycle and will automatically resume charging when replaced in charging well. The battery pack can be left in the charger storage unit when it is not being used. The charger will automatically stop charging the battery pack when fully charged. - Page 7 4. FITTING THE K-L.E.D. HEADLAMP TO YOUR LOUPE FRAME 1. To remove the loupes from the frame, hold the loupe bar between your thumb and forenger of one hand and pull away from the hinge held in your other hand. 2.
- Page 8 4. If the LED light is to be used on its own without loupes, attach the Light to the Spacer bar as shown. 5. Attach the cable to the frame sides using the cable clips provided. 6. Connect the LED light lead into the connector port on top of the battery pack.
-
Page 9: Cleaning Instructions
5. CLEANING INSTRUCTIONS Only manual non-immersion cleaning as described should be used for this light source. Do not autoclave or immerse in cleaning fluids. Do not autoclave or immerse in cleaning fluids. Always disconnect power supply from source before cleaning. a Wipe the external surface with a clean absorbent, nonshedding cloth dampened with a water / detergent solution (2% detergent by volume) or water / isopropyl alcohol solution (70% IPA by volume). -
Page 10: Annex I - Emc Statement And Guidelines
The Riester K-LED is considered to be inherently EMC benign¹, and therefore is not covered by the statements in this section ¹ Refer to section 1.1.4 of the Guide for the EMC Directive 2004/108/EC (published 21st May 2007). - Page 11 RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the Riester K-LED / charger is used exceeds the applicable RF compliance level above, the Ries- 19 ...
- Page 12 Rudolf Riester GmbH | P.O. Box 35 | Bruckstraße 31 | DE - 72417 Jungingen | Germany Tel.: (+49) +7477-9270-0 | Fax.: (+49) +7477-9270-70 | E-Mail: info@riester.de | www.riester.de...
Need help?
Do you have a question about the K-L.E.D. and is the answer not in the manual?
Questions and answers