Advertisement
Advertisement
Table of Contents
Related Manuals for International Harvester Company 75
Summary of Contents for International Harvester Company 75
- Page 4 LE FT and RIG HT indicate the left and right sides portion of the machine which carries of the riding mower when facing forward in the operator is referred to as the RIDER. The housing driver's seat. under the rider, which does the cutting, is referred to as the MOWER.
- Page 5 This symbol is used to call your attention to instructions concerning your personal safety. Be sure to observe and follow these instructions. Whenever the operator dismounts from the riding mower or leaves the riding mower unattended,disengage Know the controls and how to stop quickly. READ THE OPERATOR'S MANUAL.
-
Page 8: Starting The Engine
NOTE: The rider has an interlock safety starting system and the engine will mower clutch control is in the full disengaged position and the gear selector lever is in neutral. STARTING THE ENGINE Keep hands and feet clear of blade and all moving parts to avoid injury. -
Page 11: Height Of Cut
8e sure blade~ are assembled so the cutting edges are in the direction of rotation with the wind wings pointed toward the deck. To detach the blade, place a large wood block between cutting edge and housing to keep the blade from rotating. - Page 14 ADJUSTING MOWER adjust the mower proceed as follows: CAUTION! Stop the engine, disconnect the high tension wire to the spark plug, and lock the brake before working on the machine. 1. Place the mower height control lowest position. Engage the mower clutch. Put a pencil line on the mower housing in front of the mower front mounting brackets.
-
Page 15: Main Drive Belts
MAIN DRIVE BELTS 1 -Main drive belt 2 -Safety starting switch 3 -Mower clutch control 4 -Oil drain hole 5 -Mower drive belt idler 6 -Clutch-brake pedal return spring Underside of riding mower with mower removed to show mower drive belt, NOTE II A II -Period ically check the transm ission... - Page 18 ADJUSTABLE REAR AXLE DRIVE CHAIN CAUTION! Stop the engine, disconnect the high tension wire to the spark plug, and lock the brake the machine. After 5 hours of operation, or when excessive noise is noted, check the chain tension. The drive chain can be adjusted to compensate for stretch and wear.
-
Page 19: Carburetor Adjustments
This engine is designed to operate on unleaded or low lead gasoline with a 91 minimum (Research Method), The use of unleaded gasoline will plug and valve life, maintain longer, and reduce rust and corrosion while stored. CAUTION! Handle gasoline with care, it is highly flammable: gasoline container. -
Page 20: Spark Plug
The battery is located under the operator's seat. To service or replace the battery remove the seat. Remove the wing nut located under the center backrest of the seat. Lift the back of the seat and pull back to remove seat from front slot of seat mounting bracket. -
Page 21: Electrical System
Remove the spark plug after every 100 hours of operation for cleaning and checking the gap. When adjusting the gap, always bend the outer electrode. Never bend the insulator. electrodes is too great, the engine will misifre and be hard to start. Always use a spark plug wrench when removing or reinstalling... - Page 22 At the end of the mowing season or in the event the riding mower is to be stored for any length of time, (30 days or more) proceed as follows: Drain the fuel tank and run the engine until the fuel is exhausted from the fuel system.
-
Page 23: Engine Oil
ENGINE Oil NOTE: After checking the oil the oil must be fully seated in the filler excessive consumption operation. After the first five hours of operation, change the oil as directed in Lubrication Table. The engine oil must be drained and replaced with new oil every 25 hours engine operation... -
Page 24: Lubrication Guide
Front Wheels Mower Spindle Bearings (3) Rear Discharge Mower See Page 15. Engine Crankcase See Page 13. Mower Spindle Bearings (3) Side Discharge Mower See Page 15. Check Point of Lubrication Hours Crankcase Transmission and Differential LUBRICATION GUIDE Afer Every 10 Hours of Operation -Continued Use IH 251 H EP grease or equivalent No.2 lithium grease and apply one or two strokes of the lubricator to the grease fittings (one fitting on each front wheel). - Page 30 with No accident-prevention program can be suc- cessful without the wholehearted co-operation of the person who is directly responsible for the operation of equipment. To read accident reports from allover country is to be convinced that a large number of accidents can be prevented only by the operator anticipating the result before the accident is caused and doing something about...