Table of Contents
Advertisement
Quick Links
MICRO LINK™ "PLASMA FRIENDLY" INFRARED RECEIVER
TABLE OF CONTENTS
INTRODUCTION ............................................................................................................................................................. 1
Features ...................................................................................................................................................................... 1
Specifications .............................................................................................................................................................. 1
Installation ............................................................................................................................................................... 2
Placement ................................................................................................................................................................... 2
Mounting...................................................................................................................................................................... 2
Application Wiring ........................................................................................................................................................ 3
Advanced Wiring Configuration .................................................................................................................................... 3
3.5Mm Mini Plug Pinout ............................................................................................................................................... 4
INTRODUCTION
The 490-95 is designed to reject interference from Plasma Displays from entering the IR signal line. These Small IR
Receivers are intended to be mounted in panels, doors, cabinets, etc. for control of A/V equipment behind closed doors or
any IR Repeater System that is in close proximity of a Plasma or LCD Displays. Modeled after the original 490-90, the
490-95 offers the same features as its predecessor but in a smaller mounting frame.
FEATURES
•
Small size; mounts in ¾" diameter hole. 2¾ inches deep (70mm)
•
Quick-Connect 3.5mm Stereo Mini Plug on 7ft. (213.36cm) cable for direct plug-in to Xantech Connecting Blocks
•
Works in normal 3-wire mode (12VDC, IR, GND)
•
Green Talkback LED for System Verification
•
Improved Fluorescent Light rejection (under most conditions) and rejection from LCD Displays
•
Can be used in Direct Sunlight
•
RF Grid included for EMI interference reduction
•
Includes CB12 Connecting Block for easy connection and extension of 7' ribbon cable
•
7 units may be powered by one 781RG power supply
Note: The 490-95 will not operate in 2-wire Phantom Power mode
SPECIFICATIONS
•
Infrared modulation frequency bandwidth: 30 - 100 kHz
•
Reception range: up to 55 feet (17M), depending on local conditions
•
Reception angle: 55 degrees off axis for 50% range reduction
•
Cable requirements: 3-conductor. Use 24 gauge up to 200' (61M), 22 gauge up to 600' (182.5M), 20 gauge up to
1000' (305M), 18 gauge up to 2000' (610KM) -- unshielded OK)
•
Maximum transmission length: One mile using 18 gauge wire (1.6KM)
•
Maximum current output: 100 mA
•
Dimensions: 0.75" diameter x 2.75" deep (19mm x 70mm)
•
Power requirements: 12 volts DC @ 20 mA
INSTALLATION INSTRUCTIONS
MODEL 490-95
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Xantech 490-95
Summary of Contents for Xantech 490-95
- Page 1 INTRODUCTION The 490-95 is designed to reject interference from Plasma Displays from entering the IR signal line. These Small IR Receivers are intended to be mounted in panels, doors, cabinets, etc. for control of A/V equipment behind closed doors or any IR Repeater System that is in close proximity of a Plasma or LCD Displays.
- Page 2 Note: Plasma interference can be reflected off of any item it comes into contact with within approx. 3 ft. from the front of the display. Keeping this in mind, make sure that the 490-95 is free of any obstruction that might reflect back into the receiving eye.
- Page 3 ADVANCED WIRING CONFIGURATION 490-95 may also be used where the 7-foot lead is not long enough. In this case, simply use the CB12 Connecting Block as a “break-out” block. In Figure 4, a 490-95 is extended down to a 789-44 Connecting Block and combined with other Xantech IR Receivers.
- Page 4 This will keep the proper load balance and prevent miscommunication with the Emitters on the 789-44 CB. 3.5MM MINI PLUG PINOUT There might be times when the 490-95 needs to be wired directly to a Terminal Block. In that case you will need to cut off the 3.5mm jack and wire according to Table 1.
Need help?
Do you have a question about the 490-95 and is the answer not in the manual?
Questions and answers