Advertisement
Quick Links
OWNER'S MANUAL
XM14A
P
OWER
C 1
C 2
CAM ERA
C 3
C 4
P 1
P 2
POSITION
P 3
P 4
Cente r
Sweep
.
.
SCAN
A
O
C
.
.
M
.
.
E
.
.
K
G
Normal
Pro gra m
I
CR14A
R
EMOTE
M
VK74A P
'
T
ODEL
AN
N
I
ZC15A P
'
T
B
NCLUDES
AN
N
ILT
, CR14A
(C
POWER SUPPLY
REMOTE
S
UPPLY
C
(
AMERA
SOLD
)
SEPARATELY
ZC15A
P
'
AN
N
T
B
ILT
ASE
C
S
ILT
AMERA
YSTEM
, XM14A
ASE
ADDRESSABLE
)
AMERA SOLD SEPARATELY
Advertisement
Related Manuals for X10 Ninja VK74A
Summary of Contents for X10 Ninja VK74A
- Page 1 OWNER'S MANUAL XM14A OWER UPPLY CAM ERA POSITION Cente r Sweep SCAN Normal Pro gra m CR14A EMOTE ZC15A VK74A P ODEL AMERA ZC15A P , XM14A NCLUDES , CR14A POWER SUPPLY REMOTE AMERA SOLD SEPARATELY AMERA SOLD SEPARATELY YSTEM...
- Page 2 NTRODUCTION The VK74A includes the ZC15A Pan ‘n Tilt Camera Base with XM14A remote controlled power supply, and the CR14A remote control. You attach any XCam2 wireless camera (XX11A or XX13A) or any XCam 2 Instant On Camera (XX16A or XX17A) to the Pan ‘n Tilt Camera Base and then you can remotely control the camera’s position using a CR14A remote...
- Page 3 (supplied). Outdoors Indoors Plug power supply in here. Set the code used to turn on and off from X10 remote controls. XM14A 4 4 4 4 4 VR36A V IDEO ECEIVER Video Out Jack outdoor use). 2.4 GHz...
- Page 4 UICK ETUP Before you continue it is recommended that you follow the steps below to give the system a quick try. Later (pages 7 and 8) you can see how to connect the camera’s cord inside the top of the Ninja so you only need one power supply.
- Page 5 9. Plug the power supply into any 120V AC outlet. 10. Set the Housecode dial to a letter between A and P that matches the Housecode dial on the X10 remote controls you want to use it with. Set the Unit Code dial to a number between 1 and 4.
- Page 6 11. Set the channel switch on the camera to the same setting as the one on the VR31A or VR36A Video Receiver (A, B, C, or D). 12.Adjust the antenna if necessary to aim it in the direction of the TV that you will view the camera on.
- Page 7 EMOTE ONTROL The Remote lets you move the camera from left to right (Pan) and up and down (Tilt). You can store 4 positions for the camera and use the remote to "Sweep" between these positions. Install 4 AAA alkaline batteries (sold separately) in the remote’s battery compartment.
- Page 8 ULTI AMERA YSTEMS STOP! If you only own one Pan 'n Tilt Camera, you don't need to read any further. Important: For a Multi Camera system you will need to install a Transceiver (Model RR501 OR TM751, each sold separately). Set its Housecode to match the CR14A Remote, and XM14A power supplies you've installed.
- Page 9 If you are experiencing interference between X10 Cameras and some other equipment that uses 2.4 GHz, check the other device's owner's manual for the frequencies of each channel that it uses. X10 cameras use the following frequencies: Channel A: 2.411 GHz, Chan B: 2.434 GHz, Chan C: 2.453 GHz, Chan D: 2.473 GHz.
- Page 10 Make sure both match. · Unplug other wireless equipment such as wireless intercoms, 2.4 GHz wireless network connections, and 2.4 GHz wireless phones, that could interfere with the signal from the camera. For more help with setup please visit www.x10.com/support...
- Page 11 PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL. X10 AGREES TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE X10 PRODUCT IF RETURNED TO X10 WITHIN THE WARRANTY PERIOD AND WITH PROOF OF PURCHASE.