Teaching Mode; Threshold Value Fine Adjustment Function; Output Channel Switching; Keylock Function - Panasonic Ls-400 Series Instruction Manual

Procedures for switching the NAVI mode
RUN mode
Procedures for switching the display in RUN mode'.
TEACH
mode
Press
Refer to '

TEACHING MODE '.

L/D
mode
Press
Turn
TIMER
mode
Press
Turn
CUSTOM
mode
Press
Turn
PRO
Press
mode
Press
Procedures for switching the display in RUN mode
Incident light
Threshold
intensity
value Threshold value Incident light intensity
Press
Press
In Window comparator mode or
Hysteresis mode
Press
Threshold
value 2
Incident light intensity
Incident light intensity
Automatic
Threshold
Automatic
value 1
Incident light intensity Incident light intensity
Press
"
Note : Can be displayed if the display switching
PRO mode.

THRESHOLD VALUE FINE ADJUSTMENT FUNCTION

crease / decrease the threshold value.
mode is selected after the adjustment or any switch op-
eration is not carried out within a certain period of time.
Turn
increase or decrease after the output 1"
8

OUTPUT CHANNEL SWITCHING

Press the MODE key for more than 2 seconds when in NAVI mode. If Output 1
9

KEYLOCK FUNCTION

If the jog switch and MODE key are press down simultaneously for more than
locked.Press down for more than 3 seconds again to unlock the key.
<Key locked>
Dark ON No display
No display Light ON
No timer
OFF delay Timer period
ON delay Timer period
ONE-SHOT delay Timer period
" "
timer cannot be set.
11
Response Refer to ' PRO MODE / PRO1
mode setting'.
time selection
Refer to ' 11 PRO MODE / PRO1
M.G.S.
mode setting'.
Refer to ' 11 PRO MODE / PRO1
Emission halt
mode setting'.
Data bank Refer to ' 11 PRO MODE / PRO3
mode setting'.
loading
11
Refer to ' PRO MODE / PRO3
Code setting
mode setting'.
Press
Blinking Incident light intensity
by turns
Changed intensity
Threshold value Changed intensity
Incident light intensity
Blinking by turns
" " "
is set to to enable the display switching in PRO2 of
-
-
Turn Automatic
" or the output 2" " is displayed.
" is displayed, the following will be displayed.
Automatic Change Automatic
Select 1 indicator
Select 2 indicator
<Key unlocked>
TEACHING MODE
When teaching in Window comparator mode or Hysteresis mode, a setting has to
1. Press the MODE key once to select ' TEACH mode '. Press the
jog switch in the object present condition.
Press
2. Press the jog switch in the object absent condition. The MODE
Press
3. A threshold is set between 1 and 2.
In case stable sensing is possible: "
or
In case stable sensing is not possible: "
1. Press the MODE key once to select ' TEACH mode '. Press the
jog switch in the object absent condition.
2.
Press
3.
Turn
Automatic
4. In case stable sensing is possible:
" " blinks in the red digital display.
or
In case stable sensing is not possible:
" " blinks in the red digital display.
1. Press the MODE key once to select ' TEACH mode '. Run the
work piece on the line and hold down the jog switch.
2. " " is displayed on the green digital display and when the
Press
work piece passed through, release the jog switch. The MODE
Automatic
3. In case stable sensing is possible:
" " blinks in the red digital display.
or
In case stable sensing is not possible:
" " blinks in the red digital display.
This is the method to set the shift value to the desired value and set the threshold
range by using the single-point teaching.
<Window Comparator mode>
Set to de-
Set to de-
sired value
sired value
1_SL P-1 2_SL
1. Press the MODE key once to select 'TEACH mode'. "
displayed on the green digital display.
Blinking
2.
by turns
Press
In case stable sensing is possible:
Blinking
" " blinks in the red digital display.
by turns
In case stable sensing is not possible:
" " blinks in the red digital display.
or
mode. Furthermore, 'digit' or 'percent' can be selected. For setting method, refer to
P R O M O D E / P RO 6 m o d e s e t t in g' .
'
11
Blinking
by turns
<Window Comparator mode>
2_SL
1_SL
1. Press the MODE key once to select 'TEACH mode'. "
displayed on the green digital display. Press the jog switch in
Blinking
by turns
Press 2. " " blinks in the green digital display. Press the jog switch in the
object present condition for the second point.
Press
3.
Blinking
In case stable sensing is possible:
by turns
" " blinks in the red digital display.
In case stable sensing is not possible:
or
" " blinks in the red digital display.
Blinking
sensitivity will be set.
by turns
.
" blinks in the red digital display.
" blinks in the red digital display.
1
1
<Hysteresis mode>
Set to de- Set to de-
sired value sired value
1_SL P-1 2_SL
" is
-
-
-
<Hysteresis mode>
1_SL 2_SL
" is