Panasonic WV-RC550 Operating Instructions Manual page 6

16.
17.
18.
19.
20.
21.
22.
OFF : Set this switch to this position when recording
normally with standard shutter speeds.
100/500/1000 : Choose the suitable .shutter speed
from these when recording high speed action.
S/S : Shutter speed can be adjusted to the desired
position using SYNCRO-SCAN in Page No.3 of
the Initial set menu so that horizontal bar noise will
be reduced when this switch is set to this posi-
tion.
ELC : The ELC position makes the electric control for
the luminance with the shutter.
Note : The smear may be appeared with the high light
objects. l
Lens tris Selection Switch (IRIS, MANU/AUTO)
AUTO : The iris level of the lens is controlled automati-
cally.
Note : Be sure to set the Iris Control Selection Switch
on the zoom lens to AUTO position.
MANU : The iris level of the lens is controlled manually
by turning the Iris Level Control.
Iris Level Control
This control is used to adjust the lens iris level. The iris
level which had been automatically set, can be con-
trolled fine using this contro! when the Lens Iris
Selection Switch (16) is set to the AUTO position and
AUTO IRIS in page No.2 of Initial set menu of the WV-
E550 is set to the ADJ ON position.
Down Switch (DOWN)
This switch is used to decrease the set value of the
item pointed out by the cursor in a menu.
Up Switch (UP)
This switch is used to increase the set value of the
desired item pointed out by the cursor in a menu.
Item Switch (ITEM)
This switch is used to choose the item in the set-up
menus.
Page Switch (PAGE)
This switch is used to select the desired set-up menu
from the available menus.
Setup Switch (OFF/1/2)
This switch selects Encorder output from the Video
Output Connector and whether the User Set Function
is available as follows.
OFF : Switch set to position #1 :
Encorder is output from the Video Output
Connector on this unit and the Setup function is
not available.
ome
23.
24.
25.
26.
27.
28.
29.
30.
1/2 : Switch set to position #2 :
Encoder is output from
Connector on this unit
function is available.
the Video Output
and the Setup
Chroma Gain Fine Control (ADJUST CHROMA)
This control allows for fine adjustment of the chroma
signal level for matching the chroma levels of alt the
cameras in a system.
Adjust this control only after having set the Cable
Length Compensation Switch (25) and the Luminance
Gain Fine Control (24) to the correct position.
Luminance Gain Fine Control (ADJUST Y)
This control allows for fine adjustment of the tumi-
nance signal level for matching the levels of all cam-
eras in a system. Adjust this control only after having
set the Cable Length Compensation Switch(25) to the
correct position.
Cable Length Compensation Switch
(COARSE, 1/2/3/4)
This switch is used to compensate for extensive cable
length used with the 26-pin studio cable between this
unit and the camera.
1. Use for cable length of less than 225ft(75m)
Use for cable length of 225-450ft(75-150m)
Use for cable length of 450-690ft( 150-230m)
Use for cable length of 690-900ft(230-300m)
"A OU N
Subcarrier Phase Fine Control for Gen-lock
(SC FINE)
This control allows for adjustment of the camera signal
subcarrier phase from 0 to 360 ,to match the phase
with that of the burst signal at the Gen-lock Input
Connector in a system configuration.
Subcarrier Phase Coarse Control for Gen-lock
(SC COARSE)
The Coarse control adjusts the subcarrier phase from
0° to 360° in 90° steps, while Fine contro! allows for
continuous fine adjustment over a range of 90°.
Horizontal Phase Control for Gen-lock(H PHASE)
The horizontal phase of the camera signal can be
adjusted to much the horizonta! phase of the signal at
the Gen-lock Input Connector.
Intercom Level Control (INTERCOM, LEVEL)
Use this control to adjust the volume level in the head-
set connected to the Intercom Jack.
Intercom Jack (INTERCOM)
This jack is used for communications between the
camera operator and the Remote Control Unit opera-
tor in a system configuration with a Special Effects
Generator. (Only connection with WV-F500 or WV-
F700 series)