Advertisement
7.
10.
Detail Level Selection Switch
(DTL, LEVEL-HIGH/LOW/OFF)
The
detailfaperiure
level can
be selected
by this
switch in three steps. Set this switch to the desired
position while observing the sharpness of the picture.
Auto White/Auto Black Set Switch
(AWC/HOLD/ABC)
This switch sets the white balance and black balance
automatically as follows.
AWC : This position is used for setting the white bal-
ance
when
the White Balance Selection
Switch .
(10) is set to the A or B position of the White
Balance
Selection
Switch
(10). White
balance
adjustment
is required when
the Auto Warning
Indicator on this unit lights.
HOLD : In this position, the white and black balances
set at the AWC or ABC position can be heid fixed,
if so desired, for at least one year.
ABC : This position is used for setting the black bal-
ance even if the White Balance Selection Switch
(10) is set to any position. Black balance adjust-
ment is required when the Auto Warning Indicator
on this unit lights.
Notes :
1. While the black balance adjustment is being per-
formed
the
picture
will flash
on
the
monitor
screen.
This flashing indicates that the adjust-
ment is currently being performed and will cease
once the adjustment is completed.
2. If the Lens tris Selection Switch is set to MAN
position, Auto Black Balance
may be not per-
formed correctly.
Auto Warning Indicator (AUTO)
This indicator blinks while the white balance or black
balance is being automatically set. it.goes out once
the white and black balances have been correctly set.
This indicator lights when the white or black balance is
set improperly.
In this case, carry out the automatic
setting procedure for white and/or black balance.
White Balance Selection Switch (ATW/A/B)
This switch is used to select the auto white balance
modes as foliows.
.
ATW
: The white balance
is continuously
adjusted
automatically
A : The white balance can be set automatically by
pressing the Auto White/Auto Black Set Switch(8).
B : Similar to A, but the setting is stored in memory B.
Note : Two white balance setting, one each for differ-
ent lighting conditions such as indoor and out-
door, may be stored in the two memories, A and
B.
When
this switch is set to A or B position, the
white balance can be adjusted automatically by
using the Auto White/Black Set Switch(8).
11.
12.
13.
14.
15.
When
PAINTING
in Page No.1 of the Initial set
menu is set to the ON position, fine adjustment of
white
balance
and
R/B
pedesta!
level can
be
acheived
by using
the
Red
and
Blue
Gain
_ Controls (11) or Red
and Blue Pedestal
Level
Controls (12).
l
When this switch is set to the ATW position, white
balance can be continuously adjusted automati-
cally.
Red and Blue Gain Controls (R GAIN/B GAIN)
These controls are used to manually adjust the fine
level of white balance.
These
controls only work when
the White
Balance
Selection Switch (10) is set to A/B position and PAINT-
ING in Page No.1 of the Initial set menu is set to the
ON mode.
Turn these controls clockwise to increase the red and
blue signal levels, and counterclockwise to decrease
these levels,
Note : As these conirols employ Digital Processing,
the Red and Blue signal levels will be changed in
discrete steps.
Red and Blue Pedestal Level Controls (PED, R/B)
The fine adjustment of black balance can be set man-
ually by these controls.
These
controls only work when
the White
Balance
Selection Switch(10) is set to A/B position and PAINT-
ING in Page No.1 of the Initial set menu is set to ON
mode,
Turn these controls clockwise to increase the red and
blue
pedestal
levels,
and
counterclockwise
to
decrease the levels.
Note
: As this control employs
Digital processing,
these levels are changed in discrete steps.
Total Pedestal Level Control (TOTAL PEDESTAL)
This control can adjust the pedestal level of the video
signal(luminance)
for
matching
the
black
levels
between two or more cameras in a system. Turn this
control clockwise to increase the pedestal level, and
counterclockwise to decrease the level.
Note : As this control employs Digital Processing, this
level may be changed in the step.
Scene File Selection Switch (SCENE FILE) .
This switch is used to select the most suitable camera
preset conditions, depending on scene conditions, to
obtain the best picture possible.
Refer to the Operating Instructions of the WV-E550 for
details.
Electronic Shutter Selection Switch
(OFF/100/500/1000/ S/S/ELC)
This switch is operative only when a camera featuring
the electronic shutter function is connected with this
unit.
Advertisement
