FS S3410 Series Hardware Installation And Maintenance Manual
Hide thumbs
Also See for S3410 Series:
- Quick start manual (20 pages) ,
- Configuration manual (7 pages) ,
- Quick start manual (70 pages)
Subscribe to Our Youtube Channel
Related Manuals for FS S3410 Series
Summary of Contents for FS S3410 Series
- Page 1 S3410 Series Switch Hardware Installation and Maintenance Guide V1.0.2307A Innovation · Expertise · Agility...
- Page 2 Safety Statement： To avoid harm to people and equipment, please read the safety • recommendations in the Safety Precautions for FS Switches before installing the FS Switch. • Verify that the requirements described in the Safety Precautions for FS Switches have been met.
-
Page 3: Table Of Contents
Contents 1. Hardware Installation and Parts Replacement 1.1 Installation Procedure 1.2 Installation Preparation 1.3 Installing a Switch 1.4 Installing Modules 1.5 Connecting a Switch 1.6 Post-Installation Checks 1.7 System Commissioning 1.8 Parts Replacement 2. Troubleshooting After Installation 2.1 Troubleshooting Flowchart... -
Page 4: Hardware Installation And Parts Replacement
Hardware Installation and Parts Replacement S3410 series switches are a new generation of secure smart switches launched by FS based on the concepts of network security and easy-to-use management. S3410 series switches are a next-generation intelligent switch that features high performance, high security, multiple services and ease of use to meet the needs of the current networks. -
Page 5: Installation Procedure
Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.1 Installation Procedure Installation Preparation Installing a Switch Installing Modules System Commissioning Post-Installation Checks Connecting a Switch 1.2 Installation Preparation S3410 switch is a relatively complex device, and the installation location, networking method, power supply and alignment of the device should be carefully planned and arranged before installation. - Page 6 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.2.2 Checking the Installation S ite S3410 switch must be installed indoors.The installation site must meet the following requirements Requirement Item The device must be installed in a clean, dry, and well ventilated standard equipment room with Cleanliness controllable temperature.
- Page 7 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Procedure: Plan the available space before installing the cabinet. Maintain a clearance before the front and back doors for maintenance and operation. 2. Install and fasten the cabinet in the specified site as planned. 3.
-
Page 8: Installing A Switch
Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.3 Installing a Switch Precautions: Before installing the switch in a cabinet, please check whether the racks are properly positioned. If the racks are too close to the front door of the cabinet, you may not be able to close the front door after plugging in the Ethernet and fiber cables . - Page 9 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Workbench 1.3.2 Mounting the Switch In most cases, users do not have a standard 19-inch rack. Therefore, the most common method is to place the switch on. Although it is easy and simple, you shall pay attention to the following ：...
-
Page 10: Installing Modules
Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.4 Installing Modules 1.4.1 Installing pluggable Power Module Wear an anti-static wrist strap before the following operations. • 1. Remove the new power module from its packing materials and make sure the input specifications meet requirements. - Page 11 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.4.3 Installing an Optical Module • Before the installation, take ESD protection measures, for example, wear an ESD wrist strap or ESD gloves. • Do not touch the edge connector of an optical module during the installation. •...
-
Page 12: Connecting A Switch
Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.5 Connecting a Switch 1.5.1 Connecting Power Cables • To avoid electric shock, do not connect the power cable while the power is on. • Before connecting cables, take ESD protection measures, for example, wear ESD gloves or an ESD wrist strap. - Page 13 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 2. Lock the AC power cable with the locking strap. 3. Connect the other end of the AC power cable to the external AC power supply system. - Perform the following steps to connect the DC power cables: 1.
- Page 14 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.5.4 Connecting High-speed Cables • Before connecting cables, take ESD protection measures, for example, wear ESD gloves or an ESD wrist strap. • Both ends of an idle high-speed cable must be covered by an ESD cap. •...
- Page 15 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide To remove a high-speed cable, gently push the cable connector and then pull the handle of the connector. Do not directly pull the cable connector with force. See Figure 9. Figure 9: Removing a High-speed Cable 6.
-
Page 16: Post-Installation Checks
Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 1.5.6 Connecting the Console Port Connection Steps: Connect the RJ45 connector of an Ethernet cable to the console port of the switch, and connect the DB9 connector to a network management switch or terminal. •... - Page 17 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Step 1: Connecting the Ethernet Cable Plug the DB-9 connector of the Ethernet cable into the serial port of the PC. 2. Connect RJ45 connector of the Ethernet cable to the console port of the switch. Step 2: Check the Serial Port Number Open Device Manager on the computer and check the serial port number.
- Page 18 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Step 4: Setting Terminal Parameters Parameter requirements: Baud rate is 9600, connection type is Serial, fill in COM port number according to the actual situation. The specific diagram is as follows. Figure 11: Setting Terminal Parameters Innovation ·...
-
Page 19: Parts Replacement
Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Step 5: Once the serial port parameters are set, click <Open> to enter the CLI interface 1.7.2 Powering On the Switch Checklist before Power-On .• The switch is fully grounded. •... - Page 20 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Pull PSM-C150WACthe power module out of the slot gently. • • Install the filler panel in the empty slot to allow for adequate airflow and keep out dust. 1.8.2 Replacing an Optical Module When replacing the optical module, pay attention to the following requirements: •...
- Page 21 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Procedure: Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure that the ESD wrist strap is in close contact with your wrist, and insert the other end into the ESD jack of the device or cabinet/rack. 2.
- Page 22 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide 4. Pull out the optical module, plug the dustproof plug and dispose of it. - There are two types of buckles on the optical module. A pull-rod handle that needs to be turned over to open, as shown in Figure 16.
- Page 23 Hardware Installation and Parts Replacement Switch Hardware Installation and Maintenance Guide Procedures: Before replacing the faulty switch, be sure to clearly mark the corresponding relationship between the network cable and the port. 2. Check whether the business is ready for power-off, and save relevant business information. 3.
-
Page 24: Troubleshooting After Installation
Troubleshooting After Installation Innovation · Expertise · Agility... -
Page 25: Troubleshooting Flowchart
Check the connector of power supply module each module Check the installation of Check the LEDs on the device other modules Check serial port connection Check the cable connection and parameters Contact FS Technical Support Innovation · Expertise · Agility... - Page 26 Fault Symptom The login password is forgotten. Handling Method Contact FS technical support. Fault 2: The AC power module does not work Fault Symptom All LEDs on the front panel are off. The fan status LED is off, and the fan does not rotate. The power supply status LED is off.
- Page 27 Sometimes glitches can appear on these hardware. 5. Contact Vendor Support: If there is still no output on the serial port, please contact FS technical support. Fault 5: The serial port console output is garbled Fault Symptom The serial port console output is garbled.
- Page 28 Troubleshooting After Installation Switch Hardware Installation and Maintenance Guide Check whether the receive and transmit ends are reversed. The transmit end of an optical port must be connected to the receive end at the other end. You can confirm both ends by exchanging the connection order of two fiber cables.
- Page 29 FS has invested resources in product R&D, quality control, intelligent manufacturing, industry-leading experts, professional technical support, and networking solutions. All is to provide customers with higher-performance, lower-power consumption, and the most cost-effective products, promoting clients' network upgrades. For more information and technical support, welcome to contact us at www.fs.com/contact_us...
Need help?
Do you have a question about the S3410 Series and is the answer not in the manual?
Questions and answers