Sinoboom 1323RD Operation Manual

Hide thumbs Also See for 1323RD:

Maintenance manual (130 pages)

Table Of Contents

100

101

102

103

104

105

106

107

108

page of 108

/ 108
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

Part No.502013100002

Rev: B

Mar. 2022

Operation

Manual

产品说明书

PRODU

C T MAN U AL

1323RD/4389RD

1623RD/5389RD

0608E (2132E)

G T JZ

0808E (2732E)

G T JZ

0808E (2732E)

G T JZ

0808E (2732E)

Table of Contents

Need help?

Do you have a question about the 1323RD and is the answer not in the manual?

Questions and answers

Summary of Contents for Sinoboom 1323RD

Page 1 Operation Part No.502013100002 Rev: B Manual Mar. 2022 产品说明书 PRODU C T MAN U AL 1323RD/4389RD 1623RD/5389RD 0608E (2132E) G T JZ 0808E (2732E) G T JZ 0808E (2732E) G T JZ G T JZ 0808E (2732E)
Page 3 Operating, servicing and maintaining this vehicle or equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle or equipment in a well-ventilated area and wear gloves or wash your...
Page 4 : No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha, Hunan, China Zip Code : 410600 Copyright © Hunan Sinoboom Intelligent Equipment Co., Ltd. All Rights Reserved The final interpretation right of this manual belongs to Hunan Sinoboom Intelligent Equipment Co., Ltd.
Page 5 See the nameplate on your machine to identify the model and serial number. (See Decals/Nameplate Inspection of the Operation Manual for details.) Trade Identification Models Serial Numbers Imperial Metric 0201200100 to present 1323RD 1323RD 4389RD 0201300109 to present 1623RD 1623RD 5389RD NOTE: •...
Page 6 This Page Intentionally Left Blank...
Page 7 This manual covers the basic parts information of one or more products. Therefore, please use this manual according to your needs. If you find problems in the manual or have suggestions for improve- ment, feel free to share your feedback with Sinoboom, and we will address these issues as soon as possible.
Page 8 This Page Intentionally Left Blank...
Page 9: Table Of Contents
Crush Hazards ......3-8 Sinoboom Control System) ... 6-5 Explosion and Fire Hazards.
Page 10 Report ....... . . 9-2 Sinoboom Control System) ..6-13 Major Modification and Repair Record 9-5 Preparation .
Page 11: Introduction
The owner or administrator of the machine shall also provide the manufacturer’s maintenance information to the person responsible for maintaining the machine. If you have any questions, contact Hunan Sinoboom In- telligent Equipment Co., Ltd.. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 13: Machine Specifications
MACHINE SPECIFICATIONS Table 1-1 1323RD specifications 1323RD (METRIC) 4389RD (IMPERIAL) MEASURE DIMENSIONS Max. platform height 13.1 m 42ft 11.7in Max. working height 15.1 m 49ft 6.5in Max. horizontal reach (rear 1.2 m 3ft 11.2in extension platform extended) Max. horizontal reach (front 1.5 m...
Page 14 MACHINE SPECIFICATIONS Table 1-1 1323RD specifications (continued) 1323RD (METRIC) 4389RD (IMPERIAL) MEASURE Max. allowable inclination (side-to- 2°/0.8° side, outrigger retracted/extended) Max. outrigger leveling angle (front- 7° to-back) Max. outrigger leveling angle (side- 12° to-side) Turning radius (inside) 2.2 m 7ft 2.6in Turning radius (outside) 5.3 m...
Page 15 MACHINE SPECIFICATIONS Table 1-1 1323RD specifications (continued) 1323RD (METRIC) 4389RD (IMPERIAL) MEASURE Max. allowable ambient relative humidity Stored at -20℃ to 50℃ (-4℉ to 122℉) in a well-ventilated environment Storage condition with 90% relative humidity (20℃ [68℉]), and away from rain, sun, corrosive gas, inflammables and explosives.
Page 16 720 kPa Max. outrigger load 3200 kg 7055 lb Outrigger contact pressure 91 psi 630 kPa ENVIRONMENT Max. allowable wind speed (indoor) 0 mph 0 m/s Max. allowable wind speed 12.5 m/s 28 mph (outdoor) © Mar. 2022 1323RD&1623RD Operation Manual...
Page 17 The total vibration value of the platform does not exceed 2.5m/s², and the maximum root-mean-square value of the weighted acceleration of the entire machine does not exceed 0.5m/s². g) The hydraulic tank capacity is the maximum volume in the hydraulic tank. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 20 The machine comes in operating/raised position when the platform is raised until the down limit switch disengages. The platform height (from ground to platform floor) is 3±0.3m (9ft 10in±12in) when the down limit switch disengages. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 21: Safety
Failure to notify the manufacturer within SAFETY DEFINITIONS 48 hours of the incident involving the machine of Hunan Sinoboom Intelligent Equipment Co., Ltd. may void the product's warranty. This safety alert symbol appears with most safety statements. It means atten-...
Page 22: Electrocution Hazards
Table 3-1 Minimum Safe Distance Voltage Minimum Safe Distance (Phase to Phase, kV) (m/ft) 0-50 3.05 (10) 50-200 4.60 (15) 200-350 6.10 (20) 350 -500 7.62 (25) 500 -750 10.67 (35) 750 -1000 13.725 (45) © Mar. 2022 1323RD&1623RD Operation Manual...
Page 23 • Do not replace key parts that the platform. affect machine stability with parts of different weights or specifications. • Do not modify or change moving aerial platforms without the manufacturer’s prior written permission. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 24: Work Environment Hazards
Do not lift means other than those specified by Sinoboom, it the platform when the wind speed must be approved or guided by the manufacturer.
Page 25: Unsafe Operation Hazards
47～54 NOTICE Maximum climbing ability or gradeability is suitable for machines with platform retracted. 1323RD gradeablity: 50% (26.6°) 1623RD gradeability: 40% (22°) Gradeability means the maximum allowable tilt angle of the machine when it is on solid ground and the platform is only capable of carrying one person.
Page 26: Fall Hazards
• Do not use the machine as a crane. • Do not use the platform to push other machines or objects. • Do not allow the platform to touch nearby objects. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 27: Collision Hazards
• Maintain good judgment and plan- ning when using the controller on the ground to operate the ma- chine. Maintain proper distance between operator, machine and fixed object. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 28: Crush Hazards
Maintain good judgment and plan- maintenance requirements in the Operation Manual ning when using the controller on and the Maintenance Manual. the ground to operate the ma- chine. Maintain proper distance between operator, machine and fixed object. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 29: Bodily Injury Hazards
During operation, keep the left and right doors of the chassis closed and locked. Only trained service personnel can open the left and right doors to repair the machine. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 30 • Do not tamper with battery system to avoid serious accident. • Cut off the battery main switch if the battery is not to be used for an extended period. © Mar. 2022 3-10 1323RD&1623RD Operation Manual...
Page 31: Welding And Polishing Requirements
5. Block the wheels with the wheel wedges. 6. Charge the battery. NOTICE After using the machine, the power off switch must be disconnected. 1323RD&1623RD Operation Manual 3-11 © Mar. 2022...
Page 33: Jobsite Inspection
Operators must identify and avoid workplace hazards when mov- ing, installing and operating the machine. Unless approved by Sinoboom, never operate the ma- chine in a hazardous site. The following items present danger on the jobsite: •...
Page 35: Pre-Operation Inspection
4. The operator should go through a professional training based on this operation manual, and should be certified as a qualified operator in operation of this machine. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 36: Conducting A Pre-Operation
Before each use or work shift,check the machine for correct positioning and tightness any damaged, improperly installed, loose or missing • Ensure the rails are installed with bolts tightened. parts and unauthorized changes: • Electrical components, wiring,cables and safety ropes © Mar. 2022 1323RD&1623RD Operation Manual...
Page 37: Inspect Hydraulic Oil Level
Table 5-1 recommended to use engine oil equivalent to or higher than CH-4 with viscosity grade of 15W-40. CUSTOMER HYDRAULIC OIL REQUIREMENTS MARK Normal-temperature region L-HM46 0°C to 40°C (32°F to 104°F) Cold region L-HV32 1323RD&1623RD Operation Manual © Mar. 2022...
Page 38: Inspecting Fuel Level
An inappropriate fuel level will bring damage to the engine parts and lead to improper functioning of the machine. 1. Open the rear right door of chassis, and locate the fuel tank. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 39: Inspecting Coolant Level
The dirts or water entering the combustion system can cause severe damage to the fuel pump and injectors. Figure 5-3 1323RD&1623RD Operation Manual © Mar. 2022...
Page 40: Inspecting The Battery
• Ensure the battery connections are not corroded. • Check the battery electrolyte level is proper (for lead-acid battery requiring maintenance). • Check the battery box for accumulated water, if any, clear the water. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 41 NOTE: Add terminal protectors and antiseptic sealants to help eliminate corrosion of the battery terminals and cables. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 43: Pre-Operation Function Test
• Check the work site. NOTICE • Check the safety decals/ name- plate on the machine. All tests on the ground controller should be completed in one cycle. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 44 15. Overload indicator light 4. Key switch (Ground/Platform 10. Engine speed select switch (with 16. Emergency lowering switch select switch) indicator light) 5. Ground position 11. LCD screen 12. Platform up switch 6. Buzzer © Mar. 2022 1323RD&1623RD Operation Manual...
Page 45: Preparation
4. Ensure the LCD screen is lit and reads “SYSTEM • Never operate the machine if any READY”. control handle or switch that controls the platform movement is not returned to the OFF position after being released. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 46: Ground/Platform Select Switch
ON position, and press the engine 3. Press the platform up switch, the platform should start switch, the engine will be normally started. rise. 4. Press the platform down switch, the platform should descend and the alarm sounds. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 47: Emergency Lowering
In case of a regeneration alarm, the regeneration function will not be subject to the restriction. TESTING THE GROUND CONTROLLER (SINOBOOM CONTROL SYSTEM) NOTICE All tests on the ground controller shall be completed within one cycle. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 48 PRE-OPERATION FUNCTION TEST POWER CAUTION Figure 6-3 Ground controller (Sinoboom control system) Table 6-3 7. Neutral position 13. Platform up switch 1. Hour meter 2. Emergency stop button 8. Natural gas switch (not used) 14. Platform up/down enable switch 15. Emergency lowering 3.
Page 49: Preparation
PRE-OPERATION FUNCTION TEST POWER Figure 6-4 Ground controller (Sinoboom control system)-for EU Stage V engines Table 6-4 7. Neutral position 13. Ignition switch 1. Hour meter 2. Emergency stop button 8. Regeneration request switch 14. LED screen 3. Platform control position 9.
Page 50: Ground/Platform Select Switch
2. Pull out the emergency stop button on ground controller to ON position, and press the engine start switch, the engine can be normally started. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 51: Emergency Lowering
50 hours after the previous regeneration operation. But in the event of a regeneration alarm, this restriction is not working. TESTING THE PLATFORM CONTROLLER (DTC SYSTEM) NOTICE All tests on the platform controller should be completed in one cycle. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 52 4. Horn button 16. LCD screen indicator light) 5. Engine speed select switch (with 11. Enable switch indicator light) 6. Hydraulic generator switch (with 12. Drive/lift proportional control indicator light, if equipped) joystick © Mar. 2022 6-10 1323RD&1623RD Operation Manual...
Page 53: Preparation
Note: The switch shall be inoperative after the engine LIGHTING SWITCH (OPTIONAL) is started. Press the lighting switch, the switch should be lit and the lighting turns on. 1323RD&1623RD Operation Manual 6-11 © Mar. 2022...
Page 54: Engine Speed Select Switch
STEER THUMB ROCKER SWITCH Note: The machine is running at low drive speed by default. NOTICE When testing the steer/drive functions, the operator should stand on the platform facing towards the machine steer direction. © Mar. 2022 6-12 1323RD&1623RD Operation Manual...
Page 55: Outrigger Leveling
4. The respective outrigger should retract. AUTO AUTO AUTO POWER Figure 6-6 Platform controller (Sinoboom control system) Table 6-6 1. Individual outrigger level switch 7. Emergency stop button 13. LED screen 2. Outrigger self-level switch 8. Enable switch 14.
Page 56: Preparation
HORN BUTTON POWER Press the ignition switch, the engine should be started smoothly without abnormal noises. Press the horn button, the horn should sound. Note: This switch will be inoperative after engine startup. © Mar. 2022 6-14 1323RD&1623RD Operation Manual...
Page 57: Engine Speed Select Switch
Note: The raising/lowering speed is in direct proportion to the stroke of the joystick. STEER THUMB ROCKER SWITCH NOTICE When testing the steer/drive functions, the operator should stand in the platform facing towards the machine steer direction. 1323RD&1623RD Operation Manual 6-15 © Mar. 2022...
Page 58: Climbing Mode
3. Press the engine start switch on platform controller. 4. Press the platform lift switch. 5. Hold the joystick enable switch and slowly deflect forward the joystick to raise the platform to a height and release the joystick © Mar. 2022 6-16 1323RD&1623RD Operation Manual...
Page 59: Testing The Level Sensor
1.1±0.1Km/h (0.68±0.06mph), or the machine upon the wooden blocks. The wooden drive time for 20m (65.6 ft) is 53～64s. block dimension (L×W×H) is 100×50×70mm (4in×2in×2.76in). With the machine in operating position: 1323RD&1623RD Operation Manual 6-17 © Mar. 2022...
Page 60: Testing The Oscillate Outriggers
The oscillate outriggers enables the machine to drive 3. With the platform raised by about 1m, gradually add on uneven surfaces with 4 tires in close contact with the loads to the platform. © Mar. 2022 6-18 1323RD&1623RD Operation Manual...
Page 61 15℃ (59°F), an alarm failure will occur when the rated load is lower than the standard rated load (the "OL" symbol appears on the platform controller screen or the ground controller screen), please re-calibrate the weighing sensor. 1323RD&1623RD Operation Manual 6-19 © Mar. 2022...
Page 62 PRE-OPERATION FUNCTION TEST This Page Intentionally Left Blank © Mar. 2022 6-20 1323RD&1623RD Operation Manual...
Page 63: Operating The Machine
2. Ensure the red emergency stop buttons on ground rules and instructions in this Operation Manual. and platform controllers are pulled out to ON position. 3. Press the engine start switch. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 64: Emergency Lowering
OFF position after being released. Before operation: 1. Turn the key switch to Ground position. 2. Pull out the emergency stop buttons on ground and platform controllers to ON position. 3. Start the engine. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 65: Selecting Engine Speed
3. Start the engine. Use the color-coded direction arrows on the platform controller to identify the travel direction of the machine. NOTICE Machine travel speed is restricted when the platform is raised. To select drive speed 1323RD&1623RD Operation Manual © Mar. 2022...
Page 66: Driving On A Slope
1. Raise the platform extension locking handle to horizontal. 2. Push the handle to extend the platform to the intended position. Do not stand in the platform extension while attempting to extend the platform. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 67: Operating The Outriggers
When any outrigger is in contact with the ground, the drive and steer functions will be disabled. 1323RD: When the outriggers are retracted, the max lifting height should not exceed 13m (42.65ft). 1623RD: When the outriggers are retracted, the max lifting height should not exceed 9m (29.52 ft).
Page 69: Transporting And Lifting The Machine
3. Use the tie-down points on the chassis for the machine from rolling. anchoring down to the transport surface. 4. Use at least two chains or straps. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 70: Lifting The Machine With A Crane
1. Fully lower the platform. Keep the platform lowered during transportation. 2. Ensure the extension platforms, controllers and chassis components are adequately secured in place. 3. Remove all loose items from the machine. 4. Determine the center of gravity of the machine. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 71: Maintenance
Conduct a quarterly inspection on machines that pany to perform a pre-delivery inspection. have been out of service for a period lasting longer than three months. 2. Follow this procedure each time before delivery. Performing a pre-delivery inspection could reveal 1323RD&1623RD Operation Manual © Mar. 2022...
Page 72: Following Amaintenance Schedule
Every day or every 8 hours maintenance procedure requirements. Every quarter or every 250 hours 2. The Repair & Inspection Report shall include the inspection table of each regular inspection. © Mar. 2022 1323RD&1623RD Operation Manual...
Page 73 A-14 Functional Tests A-15 Perform Maintenance after 30 Days Checklist B Procedures REPAIRED/ YES/Machine is NO/Machine Has Problem Machine Has Items in Good Damage or Description Been Repaired Condition Malfunction B-1 Inspect Electrical Wiring 1323RD&1623RD Operation Manual © Mar. 2022...
Page 74 C-5 Inspect Carbon Brush of Motor C-6 Inspect Raising Limit Switch C-7 Inspect Staged Lowering Checklist D Procedures REPAIRED/ YES/Machine is NO/Machine Has Problem Machine Has Items in Good Damage or Description Been Repaired Condition Malfunction © Mar. 2022 1323RD&1623RD Operation Manual...
Page 75: Major Modification And Repair Record
“Good” condition before company. continuing to use the machine. Table 9-4 Major Modification and Repair Record Model Serial No. Machine Repair- Repairman’s Status Problem Description Modification/Repair Item Date Company and Signature Position ter Change 1323RD&1623RD Operation Manual © Mar. 2022...
Page 77: Decals/Nameplates Inspection
Do not operate the engine if there are missing or badly worn safety decals. 1323RD&1623RD Operation Manual 10-1 © Mar. 2022...
Page 78: Decals/Nameplates(Gb)
DECALS/NAMEPLATES INSPECTION DECALS/NAMEPLATES(GB) Restraint only for one person Restraint only for one person 101016100030 101016100030 © Mar. 2022 10-2 1323RD&1623RD Operation Manual...
Page 79 DECALS/NAMEPLATES INSPECTION Description Qty. Part No. Remarks 102006100015 Decals (GB)-1323RD Decals (GB)-1623RD 102001100013 101048103025 Decal-SINOBOOM 102012103004 Decal-1323RD use requirements 102006100008 Decal-1623RD use requirements 101012100009 Decal 102001103000 Label-D436-L3i-CN3 CODE C3OI36.3 environmental compliance 101012100018 Decal-Crush hazard 101012100029 Decal-Crush hazard 101012100030 Decal-Bulkhead overhaul...
Page 80 Decal-Landyard anchorage point 101056103002 Decal-Main power disconnect switch 101014100034 Decal-Contact information 104011100003 Decal-Hydraulic oil level 104011100010 Decal-Hydraulic oil level 104009100018 Decal-Hydraulic oil 216060000004 Decal–Caution tape, 50mm wide 101014100036 Decal-Warranty 101055103016 Decal-Emergency stop button © Mar. 2022 10-4 1323RD&1623RD Operation Manual...
Page 81: Decals/Nameplates(As)
DECALS/NAMEPLATES INSPECTION DECALS/NAMEPLATES(AS) 1323RD&1623RD Operation Manual 10-5 © Mar. 2022...
Page 82 DECALS/NAMEPLATES INSPECTION Description Qty. Part No. Remarks 102006100014 Decals (AS)-1323RD Decals (AS)-1623RD 102001100012 101048103025 Decal-SINOBOOM 102012103004 Decal-1323RD use requirements 102006100008 Decal-1623RD use requirements 101012100009 Decal 104009100021 Decal-Diesel fuel 101012100018 Decal-Crush hazard 101012100029 Decal-Crush hazard 101012100030 Decal-Bulkhead overhaul 101055103019 Decal-Electrocution hazard...
Page 83 Description Qty. Part No. Remarks 101014100026 Decal-Safety arm 101016100030 Decal-Lanyard anchorage point 101016100031 Decal-Main power disconnect switch 104009100022 Decal-Hydraulic oil 104011100003 Decal-Hydraulic oil level 104011100010 Decal-Hydraulic oil level 216060000004 Decal-Caution tape, 50mm wide 1323RD&1623RD Operation Manual 10-7 © Mar. 2022...
Page 84: Decals/Nameplates(Ce-Imperial)
DECALS/NAMEPLATES INSPECTION DECALS/NAMEPLATES(CE-IMPERIAL) © Mar. 2022 10-8 1323RD&1623RD Operation Manual...
Page 85 DECALS/NAMEPLATES INSPECTION Description Qty. Part No. Remarks 102006100013 Decals (CE-Imperial)-1323RD Decals (CE-Imperial)-1623RD 102013103004 101048103025 Logo-SINOBOOM 102012103004 Decal-1323RD use requirements 102006100008 Decal-1623RD use requirements 101012100009 Decal 104009100021 Decal-Diesel fuel 101012100018 Decal-Crush hazard 101012100029 Decal-Crush hazard 101012100030 Decal-Bulkhead overhaul 101012100005 Decal-Electrocution hazard...
Page 86 DECALS/NAMEPLATES INSPECTION Description Qty. Part No. Remarks 101014100026 Decal-Safety arm 101016100030 Decal-Lanyard anchorage point 101016100031 Decal-Main power disconnect switch 104009100022 Decal-Hydraulic oil 104011100003 Decal-Hydraulic oil level 104011100010 Decal-Hydraulic oil level 101055103015 Decal-Emergency stop button © Mar. 2022 10-10 1323RD&1623RD Operation Manual...
Page 87: Decals/Nameplates(Ce-Metric)
DECALS/NAMEPLATES INSPECTION DECALS/NAMEPLATES(CE-METRIC) 1323RD&1623RD Operation Manual 10-11 © Mar. 2022...
Page 88 DECALS/NAMEPLATES INSPECTION Description Qty. Part No. Remarks 102012103005 Decals (CE-Metric)-1323RD Decals (CE-Metric)-1623RD 102001100014 101048103025 Logo-SINOBOOM 102012103004 Decal-1323RD use requirements 102006100008 Decal-1623RD use requirements 101012100009 Decal 104009100021 Decal-Diesel fuel 101012100018 Decal-Crush hazard 101012100029 Decal-Crush hazard 101012100030 Decal-Bulkhead overhaul 101012100005 Decal-Electrocution hazard...
Page 89 DECALS/NAMEPLATES INSPECTION Description Qty. Part No. Remarks 101014100026 Decal-Safety arm 101016100030 Decal-Lanyard anchorage point 101016100031 Decal-Main power disconnect switch 104009100022 Decal-Hydraulic oil 104011100003 Decal-Hydraulic oil level 104011100010 Decal-Hydraulic oil level 101055103015 Decal-Emergency stop button 1323RD&1623RD Operation Manual 10-13 © Mar. 2022...
Page 90: Decals/Nameplates(Csa)
DECALS/NAMEPLATES INSPECTION DECALS/NAMEPLATES(CSA) © Mar. 2022 10-14 1323RD&1623RD Operation Manual...
Page 91 DECALS/NAMEPLATES INSPECTION 序号部件编号说明数量备注 102006103007 Decals (CSA)-1323RD Decals (CSA)-1623RD 102001103012 101048103025 Logo-SINOBOOM 102006103001 Decal-1323RD use requirements 102001103011 Decal-1623RD use requirements 101012100009 Decal 104009100021 Decal-Diesel fuel 101012100018 Decal-Crush hazard 101012100029 Decal-Crush hazard 101012100030 Decal-Bulkhead overhaul 101040103013 Decal-Electrocution hazard...
Page 92 Decal-Safety arm 101016100030 Decal-Lanyard anchorage point 101016100031 Decal-Main power disconnect switch 104009100022 Decal-Hydraulic oil 104011100003 Decal-Hydraulic oil level 104011100010 Decal-Hydraulic oil level 101040103015 Decal-Annual inspection 216060000004 Decal–Caution tape, 50mm wide 104011100021 Decal-Crush hazard © Mar. 2022 10-16 1323RD&1623RD Operation Manual...
Page 93: Decals/Nameplates(Ansi)
DECALS/NAMEPLATES INSPECTION DECALS/NAMEPLATES(ANSI) Restraint only for one person Restraint only for one person 101016100030 101016100030 1323RD&1623RD Operation Manual 10-17 © Mar. 2022...
Page 94 DECALS/NAMEPLATES INSPECTION Description Qty. Part No. Remarks 102006103008 Decals (ANSI)-1323RD Decals (ANSI)-1623RD 102001103006 101048103025 Logo-SINOBOOM 102006103001 Decal-1323RD use requirements 102001103011 Decal-1623RD use requirements 101012100009 Decal 104009100021 Decal-Diesel fuel 101012100018 Decal-Crush hazard 101012100029 Decal-Crush hazard 101012100030 Decal-Bulkhead overhaul 101040103013 Decal-Electrocution hazard...
Page 95 Part No. Remarks 101014100026 Decal-Safety arm 101016100030 Decal-Lanyard anchorage point 101016100031 Decal-Main power disconnect switch 104009100022 Decal-Hydraulic oil 104011100003 Decal-Hydraulic oil level 104011100010 Decal-Hydraulic oil level 101040103015 Decal-Annual inspection 216060000004 Decal–Caution tape, 50mm wide 1323RD&1623RD Operation Manual 10-19 © Mar. 2022...
Page 96 DECALS/NAMEPLATES INSPECTION This Page Intentionally Left Blank © Mar. 2022 10-20 1323RD&1623RD Operation Manual...
Page 97: Appendix 1: Symbols And Description
Collision hazards-Re- Electrocution hazards Electrocution hazards Keep a safe distance Tip-over hazards-Avoid lease brake on ramp on platform on the ground and from power lines uneven ground platform 1323RD&1623RD Operation Manual © Mar. 2022...
Page 98 Indoor use handle position and down platform Outdoor use The side force Electrocution hazards Wear protective cloth- Battery explosion ing and glasses hazard No smoking No smoking Only professional Improve point Lashing points maintenance © Mar. 2022 1323RD&1623RD Operation Manual...
Page 99 DECALS/NAMEPLATES INSPECTION personnel can start the maintenance Tire to ground load Forklift fork position Platform carrying Carrying capacity of Hydraulic oil filler capacity fixed and extended platform Horn Tool or weight Fast/high speed Slow/low speed 1323RD&1623RD Operation Manual © Mar. 2022...
Page 101: Appendix 2: Prepare The Work Record Before Delivery
2. Use the table to record the results. After each section is complete, mark the appropriate box. 3. Record the inspection results. If any inspection results are "NO", the machine must be stopped, and re-in- spected after repair is completed and the box marked "inspection" must be checked. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 103: Appendix 3: Repair & Inspection Report
30 Days Checklist B Procedures REPAIRED/ YES/Machine is NO/Machine Has Problem Machine Has Items in Good Damage or Description Been Repaired Condition Malfunction B-1 Inspect Electrical Wiring B-2 Inspect Rim, Tire and Fasteners 1323RD&1623RD Operation Manual © Mar. 2022...
Page 104 C-6 Inspect Raising Limit Switch C-7 Inspect Staged Lowering Checklist D Procedures REPAIRED/ YES/Machine is NO/Machine Has Problem Machine Has Items in Good Damage or Description Been Repaired Condition Malfunction D-1 Replace Drive Reducer Gear Oil © Mar. 2022 1323RD&1623RD Operation Manual...
Page 105 4. Record the inspection results. If any inspection item is marked as "NO", the machine must be stopped and re- inspected after repair is completed, and the box marked “REPAIRED” shall be checked. Select the appropriate inspection procedure based on the inspection type. 1323RD&1623RD Operation Manual © Mar. 2022...
Page 106 DECALS/NAMEPLATES INSPECTION This Page Intentionally Left Blank © Mar. 2022 A-10 1323RD&1623RD Operation Manual...
Page 107: Appendix 4: Major Modification And Repair Record
Modification/Repair” in the form will be “Good” and the machine can be used. If either inspection result is “NO”, the machine must be re-inspected after the repair is completed until the machine is in “Good” condition before continuing to use the machine. 1323RD&1623RD Operation Manual A-11 © Mar. 2022...
Page 108 Solution s Alw ays For B et t er A ccess Solution s Always for Better Access Solutions AS/N ZS Hunan Sinoboom Intelligent Equipment Co., Ltd. 长沙市宁乡高新技术产业园区金洲大道东 128 号 No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha, Hunan, China 市宁乡高新技术产业园区金洲大道东...

This manual is also suitable for:

4389rd 1623rd 5389rd

Sinoboom 1323RD Operation Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sinoboom 1323RD

Summary of Contents for Sinoboom 1323RD

This manual is also suitable for:

Table of Contents