Sealey CP1204 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction
protection
manual
1.

SAFETY

1.1.

GENERAL SAFETY

Maintain the Impact Wrench and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the Impact Wrench is switched off before installing the battery pack.
9
Keep the Impact Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate the work area before using the Impact Wrench e.g. ceilings, floors and enclosures may contain electrical items or water piping
9
Ensure battery pack is correctly inserted into the Impact Wrench handle and latched in place before attempting to switch on Impact
9
Wrench.
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this Impact Wrench does not need to be plugged into the mains power.
9
Keep direction switch in the locked position until the Impact Wrench is required for use.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the Impact Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the Impact Wrench.
8
DO NOT operate the Impact Wrench if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the Impact Wrench operating unattended.
8
DO NOT carry the Impact Wrench with your finger on the power switch. Keep direction switch in the locked position.
8
DO NOT use the Impact Wrench for a task it is not designed to perform.
8
DO NOT operate the Impact Wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the Impact Wrench or battery charger wet or use in damp or wet locations.
8
1.2.

HAND ARM VIBRATION

WARNING! – Risk of Hand Arm Vibration Injury.
‰
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 13.77m/s²
Uncertainty value (k): 1.5m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend
that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user or employer will need to be carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors, such as the operator, the task and the inserted
tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
1.3.

HEALTH SURVEILLANCE

We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be
modified accordingly.
1.4.

PERSONAL PROTECTIVE EQUIPMENT

We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and
dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to the
Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on
the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work.
© Jack Sealey Limited
12V SV12 SERIES 3/8"SQ DRIVE CORDLESS
IMPACT WRENCH BODY ONLY
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
CP1204
Wear a mask
CP1204 Issue 3 (ALL) 13/06/23